imilab CMSXJ33A User manual
Read this manual carefully before use,
and retainit for future reference.
EN FRDE ESIT RURU PL TR
IMILAB
Video Doorbell Set
UserManual
CONTENTS
English 01-11
12-22Deutsche
45-55Español
34-44Italiano
23-33Français
56-66Pусский
67-77Polski
78-88Türkçe
Product overview
Hub
Status LED
MicroSD
Card Slot
Speaker
Reset Button
Power
Getting started
Doorbell
Detaching
Pin
IMILAB
Video Doorbell
Mounting
Bracket
Screw Hole
Positioning Card
15° Mounting
Wedge
For video doorbell & hub installation
Mounting
Screws
and Anchors
Micro-USB
Charging Cable
EN-01
IMILAB
Smart Hub
EN-02
Video Doorbell
Microphone
Light
sensor
Speaker
Camera Lens
Micro USB
Charging Port
Doorbell Button
LED Ring
Motion Sensor
SYNC Button
Setting up the system
Download the app and set up the system
1. Download the Imilab Home APP from the app store (ios devices) or
google play (Android devices).
2. Sign up for a imilab home account , then follow the onscreen instructions to complete
the setup.
EN-03
Mounting the video doorbell
Find a Mounting Spot
Take the video doorbell to your front door and check the live view on the App at the same
time. Find a location where you can get the desired field of view.
Consider the below factors:
1.If you want to place the doorbell close to a side wall, make sure the wall doesn’t show
up in the field of view. Otherwise IR light will be reflected and night vision will become
blurry.
1.2m
(48”)
1m
(40”)
0.3m
(12”)
1.76m
（5‘9”）
2.If you are drilling the mounting holes for the first time, the recommended mounting
height is 48”/1.2 m from the ground.
3.Use the 15°mounting wedge as a supplementary mounting bracket if you wish to see
more on a specific side.
Door Video Doorbell
Without 15° Mounting wedge
(Overlook verb)
Door Video Doorbell
With 15° Mounting wedge
(Overlook verb)
15°
EN-04
Place the Screw Hole Positioning Card against the wall to mark the position.
Mount the Doorbell on a Wooden Surface
If you’re mounting the doorbell on a wooden surface, you don’t need to pre-drill pilot
holes. Use the provided screws to secure the Mounting Bracket on the wall, The Screw Hole
Positioning Card indicates the position of the screw holes. What is required: Screwdriver,
Mounting Bracket, 15° Mounting Wedge , Mounting Screws and Anchors.
Screwdriver
(not provided)
Mounting Bracket 15° Mounting
Wedge
Mounting Screws
and Anchors
Wall Mounting
Bracket
Without 15° Mounting wedge
Wall Mounting
Bracket
Mounting
Wedge
With 15° Mounting wedge
EN-05
Mount the Doorbell on Surfaces Made Out of Hard Materials
1.If you‘re mounting the doorbell on a surface made out of hard materials, like brick,
concrete, stucco, drill 2 holes through the Screw Hole Positioning Card with a 15/64”
(6mm) drill bit.
2.Insert the provided anchors,and then use provided long screws to secure the Mounting
Bracket on the wall.
What is required: Power Drill, 15/64”(6mm) Drill Bit, Mounting Bracket, 15° Mounting
Wedge , Mounting Screws andAnchors.
Power Drill
(not provided)
15/64”(6mm)
Drill Bit
Mounting Bracket 15° Mounting
Wedge
Mounting Screws
and Anchors
1
Wall Mounting
Bracket
Without 15° Mounting wedge
Wall Mounting
Bracket
Mounting
Wedge
With 15° Mounting wedge
2
EN-06
Mount the Doorbell
Align the doorbell on the bottom and then snap it on top.
Press it down until it clicks into place.
You’re all set!
If you want to detach the doorbell or recharge it, please refer to the following sections.
1
2
Charging the doorbell
5V USB Charger
Detach the Doorbell
1.Use the doorbell detaching pin provided if you wish to detach the doorbell from the
Mounting Bracket.
2.Press and hold the hole on the top of the doorbell and then lift its bottom to take it o.
What is required: Doorbell Detaching Pin.
Doorbell
Detaching Pin
1 2
EN-07
Explanations for LEDS
Hub LED Status
Blinking blue
Blue and orange
flashes alternately
Solid blue
Waiting for connection
Network connection is successful / connected
Network connection is failure
Status
Solid orange A firmware update is in progress
Press and hold the button
for 10 seconds, until the
LED blinks blue
During the reset process, the hub will restart
Blinking orange Waiting for doorbell to connect
Power
on/o
You will hear the power-on music
you will hear the power-o music
Press and hold the sync button for 2 seconds
until the blue light becomes to solid
Press and hold the sync button for 8 seconds
until the LED blinks green
Use USB to charge the
doorbell
Solid green
Charging
continuous blinking green
Fully charged
Doorbell
charging
Video Doorbell LED Status Status
Orange blinks once PIR detects motion
PIR continues to detect motionOrange blinks continuously
PIR
detection
sensitivity
adjustment
Press the doorbell button, then doorbell
indicator light will blink blue
Both the outdoor doorbell
and the indoor hub will ring
Doorbell
function
EN-08
This manual suits for next models
1
Table of contents
Languages:
