ILiving ILG8W24-51EC User manual

WALL / CEILING MOUNT AIR

CIRCULATOR

MODEL: ILG8W24-51EC

115V 60Hz 0.26HP

24” continuous variable

speed adjustment

Owner’s Manual

PLEASE READ AND

SAVE THESE INSTRUCTIONS

TABLE OF CONTENTS

Important Instructions………………………………………. 3

Specifications……………………..………………………….. 5

Installing Instructions……………………….…………..… 6-7

Operating Instructions……………………….………....… 8-9

Maintenance and Cleaning………………………………. 10

Troubleshooting……………………………………………. 11

IMPORTANT INSTRUCTIONS

CAUTION: Please read and save these instructions. Read carefully before attempting

to assemble, install, operate or maintain the product described. Do not use the fan if

any part is damaged or missing.

Protect yourself and others by observing all safety information. Failure to comply

with instructions could result in personal injury and/or property damage!

Retain instructions for future reference.

WARNING: To reduce the risk of electric shock, do not expose the fan to water or

rain. To reduce the risk of fire or electric shock, do not use this fan with any solid

state speed control device. This appliance has a grounded plug. To reduce the risk of

fire or electric shock, this plug is intended to fit in an outlet only one way. If the plug

does not fit into the outlet, contact a qualified electrician. Do not attempt to bypass

this safety feature.

General Safety Information

NOTE: To comply with UL507, air circulator is not to be used in

unattended areas.

1. Ensure that the power source conforms to the electrical requirements of the fan.

2. Where a two-prong wall receptacle is encountered, it must be replaced with a

properly grounded three prong receptacle installed in accordance with the United

States National Electrical Code (NEC) and all applicable local codes and ordinances.

This work must be done by a qualified electrician, using copper wire only.

3. Where possible, avoid the use of extension cords. If they must be used, minimize

the risk of overheating by ensuring that they are UL Listed and of the proper gauge

and length. Never use a single extension cord to operate more than one fan.

4. Do not kink the cord or allow it to contact oil, grease, chemicals, hot surfaces, or

sharp or abrasive objects.

5. This fan is to be operated ONLY with its OSHA compliant guards in place to prevent

persons and/or objects from contacting the revolving propeller. Any other use voids

warranty and may create unsafe conditions.

6. Fan is intended for general air circulation ONLY. It must NOT be used in potentially

dangerous locations such as flammable, explosive, chemical-laden, or wet

atmospheres. Do not use fan in or near a window, since rain may create an electrical

hazard. Do not attach ductwork to the fan.

7. Fan motor is equipped with an automatically resetting control circuit that will

disconnect power if the motor overheats. Always unplug fan before removing guard,

as motor may restart unexpectedly.

8. Do not operate any fan with a damaged cord or plug. Discard fan or return to an

authorized service facility for examination and/or repair.

9. Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or

similar coverings. Do not route cord under furniture or appliances. Arrange cord

away from traffic area and where it will not be tripped over.

10. Disconnect the fan when moving it from one location to another.

11. Make sure the fan is on a stable, flat surface while it is in operation.

12. Disconnect the fan when removing the guards for cleaning.

WARNING: Use of a three-prong to two-prong adapter is not

recommended. Improper connection may create the risk of electrocution.

Use of such adapters is prohibited in Canada.

WARNING: Do not depend on any switch as the sole means of

disconnecting power when installing or servicing the fan. Failure to do so

may result in fatal electrical shock.

WARNING: Do not insert fingers or foreign objects into the fan. Do not

block or tamper with the fan in any manner while it is in operation.

WARNING: Do not touch motor. May be hot enough to cause injury.

WARNING: Unplug prior to servicing unit.

WARNING: To reduce the risk of fire or electric shock, do not use this fan

with any speed control device.

SAVE THESE INSTRUCTIONS

SPECIFICATION

Model: ILG8W24-51EC

115V 60Hz 0.26HP

A: FRONT GRILLE

B: PROPELLER

C: NUTS & WASHER FOR REAR GRILLE

D: REAR GRILLE

E: THE EC MOTOR

F: INDICATOR

G: PULL CHAIN SWITCH

H: POWER CORD

I: SPEED ADJUSTMENT KNOB

J: SWIVEL BRACKET BOLT

K: NUTS & WASHER FOR SWIVEL BRACKET BOLT

L: SWIVEL BRACKET

M: HEXAGONAL BOLT

N: NUTS & WASHER FOR HEXAGONAL BOLT

O: TRIANGLE BOLT

P: NUTS & WASHER FOR TRIANGLE BOLT

Q: MOUNTING BRACKET

R: MOUNTING SCREWS

INSTALLATION INSTRUCTION

Grille/Motor Assembly:

1. Place the motor on a flat level surface with the motor shaft facing up.

2. Unscrew the 4 nuts and washers from the motor. Arrange the rear

guard in its proper position. Secure the rear guard to the motor by

inserting and tightening the 4 nuts and washers to the motor (through

the eyelets on the guard). Apply 32-40 in. lbs. of torque to motor mount

nuts.

3. Insert the propeller into the motor shaft until it reaches a stopping

point and the set screw is in line with the flat groove on the motor shaft.

NOTE: Make sure the propeller’s set screw is facing the motor. You may

need to loosen the set screw at the rear of the blade to slide it onto the

shaft.

Secure propeller on the flat of the motor shaft with the set screw. Apply

90-120 in. lbs. torque to propeller set screw.

CAUTION: Do not alter the angle of the blades.

4. Place front guard on rear guard with decal facing away from propeller.

Position guard hooks between ribs of rear guard. Use a large screw driver

to pry guard hooks into place. When assembled, the guard hooks should

be located between the largest, outermost ring and the second

outermost ring. Make sure that all hooks are engaged before operating

fan.

5. Verify that propeller does not contact the guard set at any point

before connecting fan to power supply.

Mounting Bracket:

1. Mark the drill-hole positions on the wall or ceiling (studding) for the mounting

bracket.

2. Drill the required holes with diameter fit for the anchor provided for

positioning the mounting bracket.

3. Attach the bracket to the wall or ceiling (studding) and secure with mounting

screws, or appropriately sized bolts and nuts if attaching to I-beams.

NOTE: Always install the bracket to a minimum of 2 x 4 studding.

Wall Mount

Ceiling Mount

4. Assemble the swivel bracket as shown. The bracket has three holes; be

sure square hole is specified in the illustration.

Assemble the motor to swivel bracket:

1. Position the swivel bracket in the motor yoke and align the pivot hole

with the round hole in the swivel bracket.

2. Insert the larger diameter bolt in the pivot hole and install the lock

nut, finger-tight.

3. Insert the smaller diameter bolt in the slot in the motor yoke (or

support bracket) and square hole in the pivot bracket and install

triangle knob, finger-tight.

4. While holding the motor at the desired angle, tighten the smaller

diameter bolt.

5. Tighten larger bolt to 200-230 in. lbs. and smaller bolt to 150-160 in.

lbs. being careful to maintain the desired position.

OPERATION INSTRUCTION

TO ADJUST AIRFLOW UPWARD OR DOWNWARD: Loosen the position knob first and

then loosen the pivot screw. Tilt the motor to the desired angle and then firmly

tighten the pivot screw first and then the position knob.

TO ADJUST AIRFLOW LEFTWARD OR RIGHTWARD: Loosen the swivel bracket bolt

nut a little; turn the motor to leftward or rightward to your desired position; tighten

the bolt nut.

Speed Control:

1. This fan employs the latest technology of EC (electronic commutator)

and electronic control.

2. Switch On the fan by pull chain. Pull the chain down will “click” and

fan is ON. To switch off the fan, pull the chain and “click” will switch

OFF the fan.

3. Speed adjustment is continuously variable from 200 (min) to 1200

(max) rpm via the adjustment knob.

4. Turn the knob in clockwise direction will speed up the fan and vice

verse will slow down the fan until stop.

5. Adjust the fan speed to your desire comfortable rate. Turn the knob

slowly as the fan requires time to speed up or slow down.

You can keep the desire speed when you switch off the fan. The next

time you switch on the fan, as long as the knob is at the previous

position, the fan will rotate at this speed.

CAUTION:

Rotation will always have some natural resonance frequency. This fan has

a wide spread of speed adjustment which may have encounter this

resonance at one or two speeds.

At a speed when resonance occurs, the whole fan will vibrate somewhat

vigorously and with shaking noise.

When you notice the fan is vibrating, this may be the resonance. Too

much resonance will damage the fan. Please skip this speed and you will

see the fan ceases vibrating immediately.

Resonance is nature physical phenomenon. Please skip the speed that

will cause the resonance.

MAINTENCE AND CLEANING

WARNING:Parts replacement and troubleshooting to be performed only

by qualified personnel.

WARNING:Do not depend on any switch as the sole means of

disconnecting power when installing or servicing the fan. Failure to do so

may result in fatal electrical shock.

WARNING:Unplug the fan from the wall outlet before servicing or

cleaning.

CAUTION: There is no user maintenance part except regular cleaning as

following description. All other servicing or maintenance should be

performed by qualified service personnel.

To clean the fan, use a soft damp cloth. Wipe down with a dry cloth.

Do not use cleaners that are harmful to paints or plastics.

CAUTION: Do not use gasoline, benzene, thinner, harsh cleaners, etc.,

which are dangerous and will damage the air circulator.

The propeller, guard, and motor should be cleaned periodically to

prevent overheating, and/or operating in an imbalanced condition.

CAUTION: If cleaning requires the removal of a guard, remove only the

front guard and re-install when finished in its originally installed position.

Do not repair propeller if it becomes damaged. The propeller is

accurately balanced at the factory and should be replaced if damaged.

Do not bend the blades.

Motor is permanently lubricated.

Table of contents

Other iLiving Fan manuals

iLiving

iLiving ILG8G14-12T User manual

iLiving

iLiving ILG8E18-15 User manual

iLiving

iLiving ILG8F21 User manual

iLiving

iLiving ILG8SF7V User manual

iLiving

iLiving ILG8WD24-2P User manual

iLiving

iLiving ILG8RX12 User manual

iLiving

iLiving ILG8G14-22ST User manual

iLiving

iLiving ILG8F20 User manual

iLiving

iLiving ILG937 Instructions for use

iLiving

iLiving ILG8SF301 User manual

iLiving

iLiving ILG8MF30-83 User manual

iLiving

iLiving ILG8SF10V(APB-10A) User manual

iLiving

iLiving ILG8SF16V-ST User manual

iLiving

iLiving LG8VF10 User manual

iLiving

iLiving ILG8HVLS72 User manual

iLiving

iLiving ILG8E18-15 User manual

iLiving

iLiving ILG8SF10V-ST User manual

iLiving

iLiving ILG8M24-60DC User manual

iLiving

iLiving ILG8M20-50DC User manual

iLiving

iLiving ILG8CF52B User manual

iLiving

iLiving ILG8MF72-430 User manual

iLiving

iLiving ILG8F12 User manual

iLiving

iLiving ILG8SF10V-T User manual

iLiving

iLiving ILG8P30M User manual

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual

iLiving ILG8W24-51EC User manual

Popular Fan manuals by other brands