Ikelite SLR-DC Housing User manual
Thank you for your purchase of Ikelite equipment. Please read this
instruction manual completely before attempting to operate or dive
with this product. Please refer to the back page of this manual to
register your Ikelite product.
IKELITE
SLR-DC Housing
Instruction Manual
6812.81 for the Nikon D810
2
Table of Contents
Specifications ..............................................................P. 3
Package Contents ........................................................P. 4
Preparation ..................................................................P. 4
Attach External “Tray with Handles” to Housing ............P. 4
Parts of the Housing - ront/Side View ..........................P. 5
Parts of the Housing - Back View ..................................P. 6
Initial Camera Setup........................................................P. 7
Opening the Housing ......................................................P. 7
Housing Conversion Circuitry..........................................P. 8
Setting the Conversion Circuitry Strobe ID Switch..........P. 8
Using the Conversion Circuitry........................................P. 9
lash Mode and Compensation Dial ..............................P. 9
Using Non-Ikelite or Ikelite Non-DS Strobes ..................P. 9
DS50 and DS125 Strobe Compatibility ..........................P. 10
Attaching the lash Connection for External Strobes ....P. 10
Attach Camera to Housing Tray ......................................P. 11
Installing Camera in Housing ..........................................P. 11
Closing the Housing ........................................................P. 12
inal Check ....................................................................P. 12
Attaching a Sync Cord to the Housing ............................P. 13
Turn Camera On..............................................................P. 13
Zoom Clamp & Gear Sleeve Installation ........................P. 14
Manual ocusing ............................................................P. 18
Installing the Port ............................................................P. 19
Lens Ports ......................................................................P. 20
Attaching an Ikelite Strobe Arm to the Housing Handle..P. 21
Table of Contents - continued
Usage ............................................................................P. 22
Pre-Dive Your System ....................................................P. 22
Lubricants ........................................................................P. 22
Troubleshooting ........................................................P. 23
Recommended Accessories ....................................P. 25
Accessory Mounting Points ............................................P. 25
EV-Controller Use............................................................P. 25
Maintenance..................................................................P. 26
Storing the Housing ........................................................P. 29
Spare Parts ..................................................................P. 29
Photo Tips ....................................................................P. 29
Customer Support........................................................P. 30
Limited Warranty ........................................................P. 31
Returning Products for Service ................................P. 31
Product Registration ..................................................Back Cover
3
Specifications
- Controls ............All important camera functions are accessible.
Controls are not provided for lash Compensation (provided in the
conversion circuitry only), Diopter Adjustment Control, Eyepiece Shutter
Lever, ocus Selector Lock.
- Width ................10 in (250 mm) including controls
- Height ..............6.9 in (175 mm) including controls
- Depth ................6.5 in (165 mm) including controls
- Weight ..............5.4 lb (2.4 kg) without tray & handles
- Buoyancy ..........Slightly negative in freshwater
- Depth Rating ....200 ft (60 m)
- Tray Mounting ..12-24 thread with 3 in spacing (76 mm)
4
- SLR-DC Housing
- Bag containing tray
installation hardware,
maintenance kit, and extra
control end tips.
- Aluminum Tray & Dual Handles
Package Contents
- Silicone Lubricant
- 5509.27 Standard Zoom Clamp &
Sleeve Set
- 5509.28 Large Diameter Zoom
Clamp & Sleeve Set
This product has been water pressure tested at the factory and is depth
rated to 200 ft. (60 m). Thoroughly inspect and immerse the empty
housing completely in water before installing a camera. If any fogging
occurs or droplets of water enter the housing, do not install a camera.
Clean the housing main o-ring and retest to make sure that it is
watertight. Refer to the Troubleshooting section, page 23.
We suggest that you read this instruction booklet thoroughly before use
to have a full understanding of where each camera control is located,
and what function each control provides. Please read your camera
manual thoroughly to have a full understanding of each camera function.
If you are new to underwater photography, be sure to read the Photo
Tips section.
Due to the power required to operate the camera and LCD screen, start
each dive with a fully charged camera battery.
Preparation
Attach External “Tray with Handles” to Housing
Use hardware and instructions
located in the clear Ikelite bag to
attach the “Tray with Handles” to
your Ikelite housing.
IKELITE
5
IKELITE
Parts of the Housing - ront View
Quick Release
Strobe Arm Mount
Handle
Port
pening
Gear Sleeve
Drive Gear
Shutter
Release
Power Switch
Lid
Snap
Aluminum Tray
Fn unction / Pv Button
Lens
Release
Zoom
Camera Mounting Bolt
Side View
Tray Adjustment Screw (factory set)
Bracket
Gear
Sleeve
Optional
Port
Port O-ring
Camera Tray
Movie-record
AE- /A -L
Lock
Sub-command
Dial
Lid
Snap
Shutter-release
Main Housing O-ring
Hotshoe (slide on
ca era ount)
Mode Button
6
10
2
3
4
12
13
14
7 8
18
19 20 21
22
27
1
TTL
1
-1
-1
F
-2
-3
MAN
9
5
16
11
17
6
24 25
26
23
15
Back View
1. Quick Release Button
2. Top Push Button Cluster
3. Release Mode Dial Lock Release
4. A -mode Button
5. ocus-mode selector
6. Release Mode Dial
7. Playback Button
8. Delete/format button
9. MENU Button
10. / ?Button
11. External Strobe Connector & Cap
12. Playback/Zoom in
13. Playback/Zoom out
14. OK Button
15. Super-eye Optical Viewfinder
16. AF- N Button
17. Main command dial
18. Move Cursor Up
19. Cancel and return to previous
20. Select highlighted item
21. Display sub-menu
22. Move Cursor Down
23. i Button
24. Live View Selector
25. Live View Button
26. (info) Button
27. lash Mode & Compensation Dial
WB
IS
METERING
QUAL
pening the Housing
Lid Snaps have a Lock. To open, push Lid Snap
Lock forward and lift as shown. Keep pressure
on the Lid Snap so it does not fly open quickly.
Lid Snaps have a lot of spring tension once they
go over center, so have a firm grip on the Lid
Snap. Lid Snaps may be opened one at a time.
7
Lift
Push orward Lid Snap
Lock
Initial Camera Setup (before placing camera in housing)
- Insert a fully charged battery.
- Insert a high capacity SD or Compact lash memory card.
- Set the Shooting Mode to “A” Aperture or “M” manual for shutter speeds
faster than 1/60th second.
- Set Time Zone and Date.
- Set ISO sensitivity to “200” and Meter to “Center-weighted.”
- In “M” Manual, set shutter speed to 1/60th second or 1/125th second for
fast moving subjects. Maximum shutter speed of 1/250th second
recommended to allow full power flashes from strobes.
- Set aperture to 8 for general photography or 22 for close-ups.
- Set Image Quality to “JPEG fine.”
- Set Active D-Lighting, HDR, Auto Distortion, and Long Exposure to “Off.”
- Set Multiple exposure and Interval timer shooting to “Off.”
- Set ocus mode to “A -S.”
- Set White Balance to “Auto1.” Use Preset Manual for best results and
reset for each working depth.
- In Custom Shooting menu bank A, set A -assist illuminator to “Off.”
- Make sure Red-Eye Reduction is “Off.”
* These initial camera settings are a good starting point for shooting most
underwater photos. Adjustments may be needed based on the shooting
environment and lighting conditions . Camera functions not mentioned
should be set to the shooters preference.
On the housing back is a switch
for setting the DS Strobe ID. Set
the switch to the Model of DS
Strobe being used.
When using dual strobes of
different models such as a
DS51 and a DS161, set the ID
switch to DS51 or the smaller
strobe.
8
DS DS
125
50
51
160
161
ikelite
Set DS Substrobes
to TTL Mode
200
Setting the Conversion Circuitry Strobe ID Switch
Strobe ID
Switch
Housing Conversion Circuitry
This housing contains Ikelite designed and patented Conversion
Circuitry. Once attached, turn the strobe on first before turning on the
camera.
When used with Ikelite DS Strobes the Conversion Circuitry provides
real Nikon iTTL flash exposure with over and underexposure
compensation from +1 1/3 to - 1 1/3 f-stops in 1/3 stop increments.
The Conversion Circuitry also offers Manual exposure control with 3 1/2
f-stops of underexposure control in 1/2 stop increments.
The Conversion Circuitry is powered by the Ikelite DS Strobe when
connected to the housing with the 4103.51 single or 4103.52 dual sync
cord. When using two strobes with the dual sync cord, the primary
strobe connected to the cord without the red band, must be turned on to
power the Conversion Circuitry. Always keep both strobes connected to
your dual sync cord underwater. Do not exchange your secondary
strobe for a dust cap which may not be waterproof.
Using the Conversion Circuitry (Set DS Strobe to TTL mode)
-Mode and Compensation Dial (see illustration below)
Note that the TTL compensation values are located in the yellow band.
Manual compensation values are located in the black band. Rotate the
Dial to switch between TTL and Manual Modes.
-TTL Mode compensation values are indicated in the yellow band. Place
the Setting Indicator to TTL for N Compensation. Rotate the Dial either
direction to select +/- compensation. Place the Setting Indicator to the
desired compensation value. Note that in TTL, compensation values are
in 1/3 f-stops.
-Manual Mode compensation values are indicated in the black band.
Rotate the Dial to place the Setting Indicator to the desired compensation
value. Note that in Manual Mode, compensation values are in 1/2 f-stops
from ( ) full power to -3 f-stops.
Set DS Strobe to TTL mode. This will allow the strobe power to be
varied in manual mode.
9
Setting Indicator
DIAL
TTL lash Scale (yellow = 1/3 stops)
Manual lash Scale (black = 1/2 stops)
Flash Mode and Compensation Dial
Using Non-Ikelite or Ikelite Non-DS Strobes (Strobe 50,
100A, 200, 400) with this Housing
The Conversion Circuitry is automatically disabled when used with a
Non-Ikelite or Non-DS Strobe. These Strobes can be used in their manual
mode utilizing any power settings provided on the Strobe.
10
DS50 and DS125 Strobe Compatibility
- Older DS50 Strobes with Serial Number below 63,850 can NOT be
updated to operate correctly with the latest TTL conversion circuitry.
Older DS50 Strobes with Serial Number between 63,850 and 69,999
require upgrade of electronics to operate. Strobe must be returned to
Ikelite for evaluation to provide an estimate of upgrade cost.
- Older DS125 Strobes with Serial Number below 2,500 can NOT be
updated to operate correctly with the latest TTL conversion circuitry.
Older DS125 Strobes with Serial Number between 2,500 and 4,999
require upgrade of electronics to operate. Strobe must be returned to
Ikelite for evaluation to provide an estimate of upgrade cost.
Attaching the Flash Connection for External Strobes
When using an external
strobe, connect the
housing hotshoe connector.
Slide the connector into the
hotshoe mount on the
camera from the back of
the camera as shown.
Slide the connector forward
until it stops. Due to limited
clearance between the
camera hotshoe mount and
the housing back, the
hotshoe connector should
be attached before the
camera is secured with the
mounting bolt. N TE: The camera’s built-in flash is not accessible in the
housing.
Front
D
8
1
0
External Strobe Connector
and Waterproof Cap
Housing Back
Hotshoe
Connector
Other manuals for SLR-DC Housing
12
Table of contents
Other Ikelite Camera Accessories manuals
Ikelite
Ikelite 6430 W-30 User manual
Ikelite
Ikelite 6148.28 for Canon SX280 HS User manual
Ikelite
Ikelite AF35 AutoFlash User manual
Ikelite
Ikelite 200DL User manual
Ikelite
Ikelite 5510.75 User manual
Ikelite
Ikelite 6070 Owner's manual
Ikelite
Ikelite 6146.05 User manual
Ikelite
Ikelite SD630 User manual
Ikelite
Ikelite 6184.7 User manual
Ikelite
Ikelite C-575 Owner's manual
Ikelite
Ikelite 6038.82 Owner's manual
Ikelite
Ikelite 6243.35 Owner's manual
Ikelite
Ikelite Olympus SP-350 Operating and maintenance manual
Ikelite
Ikelite 6060 Owner's manual
Ikelite
Ikelite SLR-DC Housing D700 User manual
Ikelite
Ikelite WD-3 User manual
Ikelite
Ikelite 4103.51TTL User manual
Ikelite
Ikelite Cannon HV-20 Owner's manual
Ikelite
Ikelite 6970.05 User manual
Ikelite
Ikelite Canon EOS 10D User manual
Popular Camera Accessories manuals by other brands
Viltrox
Viltrox EF-NEX Mount instructions
Calumet
Calumet 7100 Series CK7114 operating instructions
Ropox
Ropox 4Single Series User manual and installation instructions
Cambo
Cambo Wide DS Digital Series Main operating instructions
Samsung
Samsung SHG-120 Specification sheet
Ryobi
Ryobi BPL-1820 Owner's operating manual
