Ikelite 6910.63 User manual
Product Registration
Please register your product at ikelite.com within 15 days of purchase.
Our product registration database is the best way for us to get a hold
of you in the event of a product update or recall.
Underwater Housing for
Sony Alpha A6300
Product Number 6910.63
2
About this Product
Thank you for your purchase of Ikelite equipment. Please read this
instruction manual completely before attempting to operate or dive
with this product. Please visit ikelite.com to register your product to
receive information on any updates, notices, or recalls pertaining to
your equipment.
Included in the Box
• Housing
• Waterproof bulkhead cap
• Silicone lubricant
• Control + push button tip assortment
3
Important Notices
»This housing requires a compatible Lens Port for waterproof
operation. The housing is not waterproof without a Lens Port
attached.
»To prevent salt build-up and sticking controls, submerge the
empty housing in clean, freshwater. Operate the controls
several times each while underwater to ush out any residue.
»Never leave a housing in a rinse tank, even if it is the only
system in the tank. Most catastrophic oods happen when the
user walks away from a housing while it is in the rinse tank.
»Do not use alcohol, cleaning agents, spray lubricants, Rain-X,
or other solvents on the housing or lens port. Use of an
incompatible chemical compound can damage the plastic and
o-rings, and may result in leaking.
4
Contents
Product Registration 1
About this Product 2
Included in the Box 2
Important Notices 3
Getting to Know Your Housing 5
Setting Up Your Camera 7
Pre-Installation Checklist 7
Setting Up Your Housing 7
Opening the Housing 7
Inserting the Camera 8
Attaching the Hotshoe 9
Closing the Housing 9
Attaching the Lens Port 10
Final Check 11
Entering the Water 11
Setting Up An External Strobe 13
About the Built-In Flash 13
About Sync Cords 13
Attaching a Sync Cord 13
About Fiber Optic Cords 14
Attaching a Fiber Optic Cord 15
Maintenance 15
Post-Dive 15
Travel and Storage 16
Troubleshooting 16
Limited Warranty 18
Service and Repairs 19
Contact Us 20
5
Getting to Know Your Housing
Shutter
button
Power ON/OFF
Custom 1 (C1)
Electrical
bulkhead
Fiber optic ports
Tray mounts Lens port
mount
Lid
snap Lens
release
6
MENU
Fn
START/STOP
DISP
ISO
C2
MENU
Fn
START/STOP
DISP
ISO
C2
O-Ring
Control dial
Camera
Mounting
Plate
Control
wheel
AE/MF/
AEL
Flash pop
up
Fn
Custom 2 (C2)
Playback
Mode dial
Menu
Start/Stop
Control
wheel Up/
down/left/
right/center
7
Setting Up Your Camera
Pre-Installation Checklist
1. Insert a fully charged camera battery.
2. Insert a properly formatted memory card.
3. Set Smile/Face Det. to OFF.
4. Set FINDER/MONITOR to Monitor.
5. Set ISO to ISO AUTO or a specic ISO setting. Do not use ISO
AUTO Multi Frame NR setting if using a ash. This setting will
prevent the ash from ring.
ISO
Multi Frame Noise Reduct.
ISO
AUTO
AUTO
100
200
400
ISO
AUTO
Setting Up Your Housing
Opening the Housing
1. Push the lid snap lock forward and start to lift the curved end away
from the housing.
8
2. Lid snaps are designed to provide enough force to compress the
o-ring for a proper seal. Keep rm pressure against the lid snap
while lifting it away.
Lid Snap Lock
3. Repeat with remaining lid snaps.
4. Remove the housing back.
Inserting the Camera
1. Remove any lanyard or neck strap which may be attached to the
camera.
2. Check to see whether the camera’s lens will t through the port
opening of the housing. If not, the lens will need to be removed
from the camera body and re-attached AFTER the camera body is
insalled in the housing.
3. Remove the camera mounting plate from the housing.
9
4. Line the mounting screw up with the camera’s tripod socket. Use a
coin or at head screwdriver to tighten the mounting plate to the
camera.
BOTTOM SIDE
Mounting screw
1/4-20 thread
Camera tripod
socket
FRONT
5. Pull out on the housing control knobs to move them out of the way.
6. Insert the mounting plate into the slot on the inside bottom of the
housing. Push the camera all of the way forward until the back of
the mounting plate is ush with the back of the housing mount.
Attaching the Hotshoe
1. Make sure the contacts are clean.
2. Slide the hotshoe onto the camera with the LOCK marking towards
the back of the camera.
3. Push the hotshoe forward until it is unable to go any farther. The
hotshoe must be pushed all of the way forward to make proper
contact with the camera and provide TTL operation.
4. Rotate the locking ring clockwise until snug.
Closing the Housing
1. Make sure the o-ring is clean and in its proper location on the back
of the housing. The main o-ring does not require lubricant to make
a seal.
10
2. Place the back onto the housing front.
3. Make sure no controls or wires are interfering with the o-ring or the
back of the housing.
4. Place each lid snap into the corresponding hook on the housing
back.
5. Push the lid snaps towards the housing until they are at against
the housing and the lock has engaged. Close opposing lid snaps at
the same time.
6. Check the o-ring seal. The o-ring should form a uniform, solid line
around the back of the housing. There will be a small, even gap
around the housing between the housing back and the housing
front.
Attaching the Lens Port
A compatible lens port is required for waterproof operation.
Never submerge the housing without a lens port attached.
1. Lightly lubricate the o-ring on the port base. When properly
lubricated, the o-ring should have an even, slightly shiny
appearance. Wipe off any excess lubricant. Lubricant prevents the
o-ring from rolling or extruding; it is not a sealing mechanism.
2. If using a gear sleeve, place it on the port base with the teeth side
outwards.
3. Slide the lens port onto the housing port base and press evenly
down towards the housing until it stops. There should be a very
thin, even gap between the bottom of the port and the housing
front.
4. If using a dome with a shade, rotate the lens port gently so that the
wider extensions are oriented on the top and bottom. If the shade is
misaligned, it may cause vignetting (dark shadows in the corner of
the image).
Table of contents
Other Ikelite Camera Accessories manuals
Ikelite
Ikelite 6214.30 Owner's manual
Ikelite
Ikelite Canon HG-10 Owner's manual
Ikelite
Ikelite Digital Housing User manual
Ikelite
Ikelite 5510.35 User manual
Ikelite
Ikelite DLM 6” Dome Port with Zoom User manual
Ikelite
Ikelite 6950.12 User manual
Ikelite
Ikelite Digital Housing User manual
Ikelite
Ikelite 6146.07 User manual
Ikelite
Ikelite 6843.72 User manual
Ikelite
Ikelite 6242.90 Canon S90 ULTRAcompact Digital... User manual
Ikelite
Ikelite DSC-RX100M3/B User manual
Ikelite
Ikelite 6111.5 User manual
Ikelite
Ikelite 6280.31 Owner's manual
Ikelite
Ikelite DSC-HX20V User manual
Ikelite
Ikelite TG-1 User manual
Ikelite
Ikelite DLM Dome Port with Zoom Extension .375 Quick start guide
Ikelite
Ikelite S3 User manual
Ikelite
Ikelite #6184.80 User manual
Ikelite
Ikelite MD200 Owner's manual
Ikelite
Ikelite 6111.7 User manual
Popular Camera Accessories manuals by other brands
Viltrox
Viltrox EF-NEX Mount instructions
Calumet
Calumet 7100 Series CK7114 operating instructions
Ropox
Ropox 4Single Series User manual and installation instructions
Cambo
Cambo Wide DS Digital Series Main operating instructions
Samsung
Samsung SHG-120 Specification sheet
Ryobi
Ryobi BPL-1820 Owner's operating manual
