IKEA NUTID HF274 User manual
NUTID
HF274
GB
FR
DE
IT
ENGLISH 4
DEUTSCH 16
FRANÇAIS 28
ITALIANO 46
ENGLISH 4
Beforerstuse
Your safety and that of others is paramount.
Remove cardboard protection pieces,
protective lm and adhesive labels from
accessories.
Check the appliance for any transport
damage.
To avoid any damage do not place any
weights on the appliance. Do not expose
the appliance to atmospheric agents.
This manual and the appliance itself provide
important safety warnings, to be read and
observed at all times.
This is the attention symbol, pertaining
to safety, which alerts users to potential
risks to themselves and others.
All safety warnings are preceded by the
attention symbol and the following terms:
DANGER: indicates a hazardous
situation which, if not avoided, will
cause serious injury.
WARNING: Indicates a hazardous
situation which, if not avoided, could
cause serious injury.
All safety warnings give specic details
of the potential danger/warning present
and indicate how to reduce risk of injury,
damage and electric shock resulting from
improper use of the appliance. Carefully
observe the following instructions.
Precautionsandgeneral
recommendations
• The electrical installation and the
electrical connection must be carried
out by a qualied technician according
to the manufacturer’s instructions and
in compliance with the local safety
regulations. Do not repair or replace any
part of the appliance unless specically
stated in the user manual.
• The appliance must be disconnected
from the power supply before carrying
out any installation work.
• Earthing of the appliance is compulsory.
(required only for class I).
• The power cable must be long enough
for connecting the appliance, once
tted in its housing, to the power supply
socket.
• Do not pull the power supply cable in
order to unplug the appliance.
• The electrical components must not be
accessible to the user after installation.
• Do not touch the appliance with any wet
part of the body and do not operate it
when barefoot.
• The appliance is not intended for use
by persons (including children) with any
physical, sensory or mental impairment,
or without experience and knowledge
of the appliance, unless supervised or
previously instructed in its use by those
responsible for their safety.
• Do not repair or replace any part of the
appliance unless specically indicated
in the manual. All other maintenance
services must be carried out by a
specialised technician.
• Children must be supervised to ensure
they do not play with the appliance.
• When drilling through the wall pay
attention not to damage electric
connections and/or pipes.
Safetyinformation 4
Productdescription 7
Controlpanel 7
Cleaningandmaintenance 9
Whattodoif... 11
Technicaldata 12
Environmentalconcerns 13
IKEAGUARANTEE 13
SafetyInformation
Contents
ENGLISH 5
• Air vents must always discharge to the
outside.
• The manufacturer rejects all
responsibilities for any damage caused
by improper use or wrong settings.
• Appropriate maintenance and cleaning
ensure the good working order and
the best performance of the appliance.
Regularly clean all stubborn surface dirt
to avoid grease build up. Remove and
clean or change the lter regularly.
• Never ame cook food (ambé) under
the appliance. Using free ames might
cause re.
• Failure to observe the instructions for
cleaning the hood and replacing the
lters may result in a re.
• Exhaust air must not be vented through
a ue used for removal of fumes
produced by gas combustion appliances
or other combustible materials, but must
have a separate outlet. All national
regulations governing extraction of
fumes must be observed.
• There shall be adequate ventilation if
the hood is being used at the same time
as other appliances using gas or other
combustible materials. The negative
pressure of the room must not exceed 4
Pa (4x 10-5 bars). For this reason ensure
that the room is well ventilated.
• Do not leave frying pans unattended
when frying, as the frying oil may catch
re.
• Before touching the light bulbs, ensure
that they are cold.
• Do not use or leave the hood without
the light bulb correctly tted, as this may
cause electric shock.
• The hood is not a work surface, therefore
do not place any objects on top of it or
overload it.
• During all installation and maintenance
operations wear appropriate working
gloves.
• This appliance is not suitable for outdoor
use.
WARNING: when the hob is in use,
accessible parts of the hood may
become hot.
Installationandconnection
After unpacking the appliance, check for
any transport damage. In the event of
problems, contact the After-sales Service.
To prevent any damage, only remove
the appliance from its polystyrene foam
packaging at the time of installation.
Preparingforinstallation
WARNING: this is a heavy product; the
hood should only be lifted and
installed by two or more people.
Before installation also check the minimum
distances stated in the manual of the cooker.
If the installation instructions for the cooker
specify a greater distance between cooker
and hood, this distance must be observed.
Electricalconnection
Make sure the power voltage specied on
the appliance rating plate is the same as
the mains voltage.
This information can be found on the inside
of the hood, under the grease lter.
Power cable replacement (type H05
VV-F) must be carried out by a qualied
electrician. Contact an authorized service
centre.
If the hood is tted with an electric plug,
connect the plug to a socket complying with
current regulations, located in an accessible
place.
If no plug is tted (direct wiring to the
mains), or if the socket is not located in an
accessible place, a qualied electrician
should install a standardised double pole
power switch that will enable complete
isolation from the mains in case of category
III overvoltage conditions, in accordance
with wiring rules.
ENGLISH 6
Use
The hood has been designed to be installed
and used either as a “Exhausted model”, or
as a “Recirculation model”.
Exhaustedmodel(seesymbol in
installationbooklet)
Cooking steam is sucked and channelled
outside the house through a discharge duct
(not supplied), tted to the hood steam
outlet.
Ensure that the discharge duct is correctly
tted to the air outlet, unit using an
appropriate connection system.
Important:If already installed, remove the
charcoal lter/s.
Recirculationmodel(seesymbol in
installationbooklet)
The air is ltered through one or more the
charcoal lters, and then resent into room.
Important:Ensure appropriate air
circulation around the hood.
Important:If the hood is supplied without
charcoal lters, these must be ordered and
tted before the hood can be used.
The hood should be installed away from
particularly dirty areas, windows, doors and
heat sources.
The hood is sold with all necessary
components for installation on most types of
walls or ceilings. However, ask a qualied
technician to check that the items supplied
are suitable for the type of wall/ceiling.
Keep this booklet for future consultation.
ENGLISH 7
Productdescription
1 Control Panel.
2 Grease lter.
3 Light.
4 Inside light.
5 Steam deector.
6 Aesthetic pattern.
7 Support cables.
8 Interconnection cable.
9 Boss.
46
1
2
8
33
5
Controlpanel
Extractionspeed(power)control
A Led.
B Extractor power selection button.
C Light switch.
9
7
A
C
B
Preliminary information for correct use of the
hood:
Use the highest speed in case of particularly
concentrated cooking steam. It is advisable
to switch the hood on 5 minutes before
starting to cook and leave it running for
another 15 minutes at the end of cooking.
Automaticswitchingonfunction
The hood is equipped with a temperature
sensor that activates the motor at extraction
speed (power) 1 when the temperature in
the area around the hood exceeds 70°C.
The user can in any case switch off or
change the extraction speed (power) (see
section “Extraction speed (power)
control”).
ENGLISH 8
Extraction speed (power) selection is cyclic
according to the speed sequence
therefore every time the “extraction power
selection” button is pressed, the extraction
speed (power) increases by one level
and switches off (Stand-by) if the button
is touched again when the hood is on
extraction speed (power) 4.
Note: Extraction speed (power) 4 remains
on for 5 minutes, after which the extraction
motor switches to speed 2.
By pressing it again the extraction motor
switches off (Stand-by).
The hood can also be switched off (Stand-
by) when it is on any speed, by prolonged
pressing (more than 3 seconds) of the
button.
The control panel has a led that changes
colour according to the extraction speed
(power), therefore hood extraction speed
(power) can be determined as follows:
Hood on stand-by: LED OFF
extraction speed
(power) 1: Led GREEN
extraction speed
(power) 2: Led ORANGE (amber)
extraction speed
(power) 3: Led RED
extraction speed
(power) 4: Led RED FLASHING
Controlofbottomlamps
The bottom light can be switched on or off
by pressing the “light button”.
Controlofinsidelamps
The inside lights can be switched on or
off by PROLONGED pressing of the “light
button”.
As well as as switching on and off,
PROLONGED PRESSING also allows the
brightness of the lamps to be adjusted.
Note: the switching on and off (and
adjustment) functions alternate.
Reset and conguration of lter saturation
signalling
Switch the hood on at any speed (see
section above “Extraction speed (power)
control”)
Resetgreaseltersaturationsignalling
(GREENLEDFLASHINGoncontrolpanel)
Firstly carry out lter maintenance as
described in the relevant section.
Press (prolonged for more than 3 seconds)
the “extraction power selection” button; the
LED stops ashing to indicate that
signalling has been reset, and the hood
switches off.
Resetcarbonltersaturationsignalling
(ORANGE(amber)LEDFLASHING)
Firstly carry out lter maintenance as
described in the relevant section.
Press (prolonged for more than 3 seconds)
the “extraction power selection” button; the
LED stops ashing to indicate that
signalling has been reset, and the hood
switches off.
Deactivationofcharcoalltersaturation
signalling(forparticularapplications)
Switch off the hood (see section above
“Extraction speed (power) control”)
Press (prolonged for more than 5 seconds)
the “extraction power selection” button; the
LED ashes GREEN (amber) to
indicate that carbon lter saturation
signalling has been deactivated.
To reactivate charcoal lter saturation
signalling, repeat the operation, and the
LED will ash ORANGE.
ENGLISH 9
WARNING:
- Never use steam cleaning equipment.
- Disconnect the appliance from the power
supply.
IMPORTANT: do not use corrosive or
abrasive detergents. If any of these products
accidentally comes into contact with the
appliance, clean immediately with a damp
cloth.
• Clean the surfaces with a damp cloth.
If it is very dirty, add a few drops of
washing up detergent to the water.
Finish off with a dry cloth.
IMPORTANT: do not use abrasive sponges
or metallic scrapers or scourers. Over time,
these can ruin the surface.
• Use detergents specically designed for
cleaning the appliance and follow the
manufacturer instructions.
IMPORTANT: clean the lters at least
monthly to remove any oil or grease
residuals.
Lampmaintenance:
1. Disconnect the hood from the power
supply.
2. Replace the damaged lamp.
3. Only use halogen lamps 20W max GU4
- 12V - Ø 35mm - 30° - taking care not
to touch them with hands.
Replacingtheinsidelamps
First unscrew the screws.
Pull the pattern downwards and unscrew the
damaged lamp; only use 40W max (E14)
olive-shaped lamps.
Greaselters:
The metal grease lter has an unlimited life
and must be cleaned once a month by hand
or in a dishwasher at a low temperature and
with a short cycle.
Cleaning in a dishwasher may cause
discolouring of the grease lter, but its
ltering efciency is unaffected.
Greaseltermaintenance:
1. Disconnect the hood from the power
supply.
2. Remove the grease lter by pulling the
spring release handle.
Cleaningandmaintenance
ENGLISH 10
3. Remove the carbon lter tted on the
grease lter.
Grease lter cleaning required: GREEN led
FLASHING (read the relevant instructions in
“Reset and conguration of lter saturation
signalling”)
Charcoalltermaintenance
The charcoal lter must be cleaned once
a month in a dishwasher at the highest
temperature, using a normal
dishwasher detergent. Wash the lter
separately.
After washing, reactivate the carbon lter by
drying it in the
oven at 100°C for 10 minutes.
Change the charcoal lter every 3 years.
Charcoal lter cleaning or changing
required: ORANGE (amber) led FLASHING
(read the relevant instructions in “Reset
and conguration of lter saturation
signalling”)
Table of contents
Languages:
Other IKEA Ventilation Hood manuals
IKEA
IKEA IHW6530BS0 User manual
IKEA
IKEA UDDEN HW320 User manual
IKEA
IKEA Rytmisk User manual
IKEA
IKEA IHW6362VM0 Product information sheet
IKEA
IKEA IH6362WS0 User manual
IKEA
IKEA 403.921.95 User manual
IKEA
IKEA FINSMAKARE User manual
IKEA
IKEA FRAMTID HW280 User manual
IKEA
IKEA UNDERVERK User manual
IKEA
IKEA FRAMTID HW380 User manual
IKEA
IKEA LUFTIG User manual
IKEA
IKEA IH6242WM0 Product information sheet
IKEA
IKEA FINSMAKARE User manual
IKEA
IKEA FORTROLLA User manual
IKEA
IKEA BEMOTA User manual
IKEA
IKEA UTDRAG User manual
IKEA
IKEA LUFTIG User manual
IKEA
IKEA LAGAN User manual
IKEA
IKEA LAGAN 504.013.83 User manual
IKEA
IKEA SVÄVANDE User manual
