IKA Mini MR standard User manual

20000009672

IKA®Mini MR standard

Mini MR standard_032018

Page

Safety instructions 8

Operator’s control 9

Unpacking 9

Correct use 9

Installation 10

Maintenance 10

Accessories 10

Warranty 10

Technical data 11

Contents

Safety instructions

For your protection

•Read the operating instructions in full before starting up and

follow the safety instructions.

• Keep the operating instructions in a place where they can be accessed

by everyone.

• Ensure that only trained staff work with the appliance.

• Follow the safety instructions, guidelines, occupatinal health and save-

ty and accident prevention regulations.

• Caution - Magnetism! Effects of the magnetic ﬁeld have to be taken

into account (e.g. data storage media, cardiac pacemakers ...).

• Wear your personal protective equipment in accordance with the haz-

ard category of the media to be processed.

Otherwise there is a risk from:

- splashing and evaporation of liquids

- ejection of parts

- release of toxic or combustable gases.

• Use only the AC adapter supplied.

• Set up the appliance in a specious area on an even, stable, clean, non-

slip, dry and ﬁreproof surface.

• The base plate must be clean and intact.

• Check the appliance and accessories before hand for damage each

time you use them. Do not use damaged components.

• Reduce the speed if

- the medium splashes out of the vessel because the speed is too high

- the appliance is not running smoothly

- the container moves on the base plate.

• Beware of hazards due to:

- ﬂammable materials

- combustible media with a low boiling temperature

- incorrect container size

- overﬁlling of media

- unsafe condition of container.

• The appliance may heat up when in use.

• Process pathogenic materials only in closed vessels under a suitable

extractor hood. Please contact IKA if you have a questions.

• Do not operate the appliance in explosive atmospheres, with hazard-

ous substances or under water.

• Only process media that will not react dangerously to the extra energy

produced through processing. This also applies to any extra energy

produced in other ways, e.g. through light irradiation.

• Safe operation is only guaranteed with the accessories described in

the “Accessories” chapter.

• The centre of gravity of the assembly must lie within the surface on

which it is set up.

• The appliance must only be disconnected from the mains supply by

pulling out the plug-in power supply unit.

• The socket for the the plug-in power supply unit must be easely ac-

cessible.

• The appliance starts up again atomatically following a cut in the pow-

er supply.

• Abrasion of the dispersion equipment or the rotating accessories can

get into the medium you are working on.

• Whem using the PTFE-coated magnetic bars, the following has to be

noted: Chemical reactions of PTFE occur in contact with molten or dis-

solved alkaline and alkaline-earth metals, as well as with ﬁneparticeld

Operator’s control

Unpacking

Correct use

powders of metals of the 2. and 3. group of the periodical system at

temperatures above 300-400 °C. Only elementary ﬂuorine, chlorine

triﬂuoride and alkaline metals do attack PTFE, halogen hydrocarbons

have a reversible swelling effect.

(Source: Römpps Chemie-Lexikon and „Ullmann“ Bd.19)

To the protetion of the equipment

Attention: The appliance must not be overpoured with ag-

gressive media! Never put the appliance under water!

• The voltage stated on the nameplate must correspond to the mains

voltage.

• Do not cover the device, even partially e.g. with metallic plates or ﬁlm.

This results in overheating.

• Protect the appliance and accessories from bumps and impacts.

• Ensure that the base plate is kept clean.

base plate connector socket

rotating knob

• Unpacking

- Please unpack the device carefully

- Inthe case of any damage a fact report must be set immediately

(post, rail or forwarder)

• Delivery scope

- Magnetic stirrer

- Plug-in power supply

- Operating instruction

• Use

- for mixing liquids

• Range of use

- Laboratories - Schools

- Pharmacies

Starting up Accessories

Warranty

Maintenance

- Set the knob to the left stop

- Place a magnetic rod in a vessel which is penetrable for magnetic ﬁeld

lines and ﬁll the vessel with the medium to be processed.

- Place the vessel on the centre of the base plate.

- Connect the appliance to a socket (the voltage stated on the name-

plate must correspond to the mains voltage).

- Set the speed using the knob

The appliance is maintenance-free.

Cleaning

Only use cleansing agents which have been

recommended by IKA.

Use to remove:

Dyes Isopropyl alcohol

construction materials water containing tenside,

isopropyl alcohol

Cosmetics water containing tenside,

isopropyl alcohol

Foodstuffs water containing tenside

Fuels water containing tenside

- Do not allow moisture to get into the appliance when cleaning.

- Wear protective gloves during cleaning the devices.

- Before using another than the recommended method for cleaning or

decontamination, the user must as certain with IKA that this method

does not destroy the instrument.

IKA - stirring bars:

TRIKA®25

IKAFLON®20 (recommendation)

IKAFLON®30

Stirring bar remover

In accordance with IKA warranty conditions, the warranty period is 24

months. For claims under the warranty please contact your local deal-

er. You may also send the machine direct to our factory, enclosing the

delivery invoice and giving reasons for the claim. You will be liable for

freight costs.

The warranty does not cover worn out parts, nor does it apply to faults

resulting from improper use, insucient care or maintenance not car-

ried out in accordance with the instructions in this operating manual.

Technical data

Number of stirring positions 1

Stirring quantity max. per stirring position

(H2O)

Motor rating output W2

Direction of rotation right

Speed control turning

knob

Speed min. rpm 0

Speed max. rpm 2500

Stirring bar length min. mm 20

Stirring bar length max. mm 40

Set-up plate material polyester

Set-up plate dimensions mm 115x115

Automatic reverse rotation no

Intermittent mode no

Viscosity trend measurement no

Break detection stirring bar no

Timer no

pH measurement no

Graph function no

Programs no

Sensor in medium detection (Error 5) no

Weighing function no

Set-up plate illuminated no

Width mm 115

Depth mm 129

Height mm 37

Weight kg 0.25

Permissible ambient temperature min. °C 5

Permissible ambient temperature max. °C 40

Permissible relative humidity %80

Protection class according to DIN EN 60529 IP 42

USB interface no

RS 232 interface no

Analog output no

Voltage V100-240

Frequency Hz 50/60

Power input W3

DC Voltage V12

Current consumption mA 300

Subject to technical changes!

Other manuals for Mini MR standard

Other IKA Laboratory Equipment manuals

Popular Laboratory Equipment manuals by other brands

Qiagen

Qiagen DML 3000 user manual

Queensgate

Queensgate NANOSCAN OP400 Quick start instructions

Conviron

Conviron GEN1000-GE Operator's manual

Parr Instrument

Parr Instrument 4560 Operating instructions manual

Integra

Integra DOSE IT operating instructions

Agilent Technologies

Agilent Technologies 5800 ICP-OES user guide

Endress+Hauser

Endress+Hauser Cleanfit CPA875 operating instructions

NI PXI-5422 CALIBRATION PROCEDURE

Collomix

Collomix Aqix operating instructions

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series operating manual

Ocean Insight

Ocean Insight FLAME-NIR+ Installation and operation manual

Parker

Parker ALIGN-MG-NA Installation, operation and maintenance manual

BD 644787 user guide

DENTAURUM

DENTAURUM Compact Megaplus Instructions for use

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 instruction manual

VWR

VWR SAS Super IAQ instruction manual

illumina

illumina MiSeqDx reference guide

Yamato

Yamato BM510 instruction manual