iDevices Wall Outlet User manual
1
INSTALLATION & SETUP GUIDE
iDEVICES SMART HOME SOLUTIONS
2
REQUIRES
• Wi-Fi®2.4 GHz 802.11 b/g/n Compatible Network
• Router Security Settings Supported: WPA, WPA2, Or None
• Free iDevices®Connected App
• 120VAC “Line” (usually black, blue or red) And “Neutral”(usually white) Wires
• Controlling this HomeKit-enabled accessory requires an iPhone, iPad, or
iPod touch with iOS 8.1 or later
• Android™ 4.3+ Device With Bluetooth®Smart Technology
NOTE: 5 GHz networks are not compatible.
TOOLS NEEDED
• Philips Screwdriver
• Flathead Screwdriver
• Pliers
• Wire Cutter/Stripper
• Voltage Detector
RATINGS
Input: 125VAC, 60Hz
Output: 125VAC, 60Hz
Tungsten: 600W (5A)
General Use: 15A
Motor: 1/2 HP
Resistive: 1800W (15A)
3
REQUIRES
• Wi-Fi®2.4 GHz 802.11 b/g/n Compatible Network
• Router Security Settings Supported: WPA, WPA2, Or None
• Free iDevices®Connected App
• 120VAC “Line” (usually black, blue or red) And “Neutral”(usually white) Wires
• Controlling this HomeKit-enabled accessory requires an iPhone, iPad, or
iPod touch with iOS 8.1 or later
• Android™ 4.3+ Device With Bluetooth®Smart Technology
NOTE: 5 GHz networks are not compatible.
• Not intended for critical medical or life support equipment.
• Use caution when using the iDevices®Wall Outlet to control any appliances which produce heat or
mechanical motion, or could create a hazardous condition when operated while unattended.
• The iDevices®Wall Outlet is not user-serviceable. Do not attempt to open the enclosure for any reason.
• The iDevices®Wall Outlet must be installed in a manner that conforms to all applicable national,
state, and local building codes.
• The iDevices®Wall Outlet is intended for dry, indoor use only.
• Ambient operating conditions: 32º F to 104º F (0º C to 40º C), 0-90% humidity, non-condensing.
• The iDevices®Wall Outlet is not a Ground Fault Circuit Interrupt (GFCI) or Arc Fault Circuit Interrupt
(AFCI) protected outlet.
• The iDevices®Outlet should be installed in a circuit with a breaker/fuse rated at no more
than 15 Amps. The total load (both receptacles combined) should not exceed 1800W.
• Notice - Use only copper or copper-clad wire with this device.
RISK OF ELECTRIC SHOCK, SEVERE BURNS, AND FIRE: Your safety is important to us.
Electricity is dangerous and can cause personal injury and property damage if handled improperly.
A working knowledge of electrical installation is required to install this product. If you are not
comfortable working with electricity do not attempt to install the iDevices®Wall Outlet and seek
professional assistance from a qualied electrician.
!
4
BEFORE YOU START
• Read through this Installation Guide in its entirety before starting
installation of your iDevices®Wall Outlet or removal of your old
outlet. Incorrect installation can be dangerous and can damage
your iDevices®Wall Outlet or your home.
• Visit our YouTube channel for tips on installation and setup:
www.YouTube.com/User/iDevicesInc
• Turn OFF the power to the circuit you are working on at your
home’s breaker or fuse panel.
5
• Wherever possible, install the iDevices®Wall Outlet in a non-
metallic gang box and use a non-metallic faceplate, as metal gang
boxes and faceplates can decrease the Wi-Fi®signal strength.
• Check that your mobile device is compatible with the iDevices®
Wall Outlet at iDevicesinc.com/Compatibility
• It is YOUR responsibility to be sure that products are installed in
accordance with applicable building codes. Check with your local
building ofce if you have questions.
• Download the free iDevices®Connected app.
6
GETTING TO KNOW THE
iDEVICES®WALL OUTLET
Top Outlet ON/OFF. Pressing this button will turn the individual outlet
ON or OFF. DEVICE RESET: Press and hold for 10 seconds until LED
blinks red. PAIRING MODE: Press and hold for 3 seconds until LED is
solid blue.
Bottom Outlet ON/OFF. Pressing this button will turn the individual
outlet ON or OFF. DEVICE RESET: Press and hold for 10 seconds until
LED blinks red. PAIRING MODE: Press and hold for 3 seconds until LED
is solid blue.
Status LED/Night Light. Provides setup status and used as a night light
during operation. Refer to LED color codes on page 16.
1
2
3
7
Pull Out Tab. Refer to this
when prompted to enter your
HomeKit™ code during the setup
on a iOS device.
Device Reboot. Pressing this
cycles power to the entire unit. 1
4
4
2
5
5
3
8
INSTALLATION
STEP 1
Take a photo of your existing wiring for future reference. Turn OFF
the power to the circuit at your breaker or fuse panel. If you are
replacing an existing outlet, verify that the outlet no longer has power
before proceeding.*
STEP 2
Wire the receptacle in place of an existing receptacle according to
the adjacent diagram with the provided wire nuts. Ensure the wire
nuts are fastened securely.
*If the outlet is in a multiple-gang box (with two or more switches and/or outlets), make sure that all
circuits in the gang box are turned off at the breaker or fuse panel.
9
GROUND (USUALLY BARE COPPER
OR GREEN)
GROUND
(BARE COPPER)
LINE (USUALLY BLACK)
LINE
(BLACK)
NEUTRAL (USUALLY WHITE)
NEUTRAL
(WHITE)
10
STEP 3
Secure the iDevices®Wall Outlet back into the gang box.
STEP 4
Turn the power back ON at the breaker. If the outlet is connected
properly, you should see the LED indicator rapidly ash blue to
indicate the unit is ready to connect to the app.
Table of contents
Other iDevices Accessories manuals
