ICP DAS USA VPD-173N User manual
VPD-173 Quick Start, version 1.0 Last Revised: May 2015 Page: 1
Thanks for buying a VPD-173N device.
1. What’s in your package?
VPD-173N /
VPD-173N-64
Quick Start
2.4mm screw driver
2. Pin Assignments
VPD-173N / VPD-173N-64
Quick Start Version 1.0
VPD-173 Quick Start, version 1.0 Last Revised: May 2015 Page: 2
Power :
No
Mode
Description
0
F.G.
Frame Ground. F.G. is connected to the inside
EMI or ESD suppression circuits. Make sure
that F.G. is connected to the Earth
1
PWR
DC input Voltage (range: +12V ~ +48V)
2
GND
Connected to the power supply’s ground pin
Serial ports :
No
Mode
Description
0
D+
The positive data line of the RS-485 network
1
D-
The negative data line of the RS-485 network
2
GND
The common ground of the RS-232
3
Rx
The pin of received data of the RS-232
4
Tx
The pin of transmitted data of the RS-232
The definition of the rotary switch:
No
Mode
Description
0
Run
&Update
Run or update the program. This mode is
used in the development phase.
1
Force
Update
If TPD has a serious crash, force TPD to
update the program.
2
Run Only
Only run the program.
VPD-173 Quick Start, version 1.0 Last Revised: May 2015 Page: 3
3. Appearance
4. First Use of VPD-173N series
1. Connect wires as the
figure and set the rotary
switch to zero.
2. Turn on the power
supply to the VPD, and
then you can see the
default program run on
it.
VPD-173 Quick Start, version 1.0 Last Revised: May 2015 Page: 4
5. Creating First Project
To create your first project of the VPD series, install the free
development tool, HMIWorks and then refer to
<<TouchPAD_getting_started.pdf>>, which can be found on the
FTP:
ftp://ftp.icpdas.com/pub/cd/touchpad/document/english/getting_st
arted
Additional Links
TPD/VPD series product page:
http://www.icpdas.com/root/product/solutions/hmi_touch_monitor/touchpad/tou
chpad_selection.html
Documents, such as the user manuals, the API references, etc.:
ftp://ftp.icpdas.com/pub/cd/touchpad/document/english/
Free development software, HMIWorks v2.09.15 or above:
ftp://ftp.icpdas.com/pub/cd/touchpad/setup/
If you have any problem, feel free to contact us.
E-mail: service@icpdas.com
VPD-173 Quick Start, version 1.0 Last Revised: May 2015 Page: 5
感謝您購買 VPD-173N 系列產品。
1. 檢查包裝内含物品
VPD-173N /
VPD-173N-64
產品須知
2.4mm 螺絲刀
2. 接腳定義
VPD-173N / VPD-173N-64
產品須知 版本 1.0
VPD-173 Quick Start, version 1.0 Last Revised: May 2015 Page: 6
電源 :
No
Mode
Description
0
F.G.
機架接地，F.G. (連接到內部的 EMI 或ESD 保護電
路)，請接到大地
1
PWR
直流電壓輸入 (範圍：+12V ~ +48V)
2
GND
連到電源的接地端
通訊介面 :
No
Mode
Description
0
D+
RS-485 網路的正訊號線
1
D-
RS-485 網路的負訊號線
2
GND
RS-232 共同的接地點
3
Rx
RS-232 的接收資料腳位
4
Tx
RS-232 的傳送資料腳位
旋轉開關定義:
No
Mode
Description
0
Run
&Update
執行或是更新程式，是程式開發階段使用的。
1
Force
Update
當TPD 上面的程式嚴重毀損時，強制更新程
式。
2
Run Only
僅執行程式。
VPD-173 Quick Start, version 1.0 Last Revised: May 2015 Page: 7
3. 外觀
4.第一次使用 VPD-173N
1. 如圖所示，將電源和接地線連
接完成。然後將旋轉開關
(rotary switch)轉到零。
2. 打開供電給 VPD 系列的電
源，接著可以看到 VPD 系列
執行出貨預附的程式如圖所
示。
VPD-173 Quick Start, version 1.0 Last Revised: May 2015 Page: 8
5.建立第一個軟體專案
在建立 VPD 系列的第一個專案之前，請先安裝免費的開發軟體 HMIWorks。
然後參考<<TouchPAD_getting_started.pdf>>這份文件，一步一步地完成。
該份文件可以在下列 FTP 上找到：
ftp://ftp.icpdas.com/pub/cd/touchpad/document/chinese/getting_started
下面的連結有更多的資訊
TPD/VPD 系列產品的網址：
http://www.icpdas.com/root/product/solutions/hmi_touch_monitor/touchpad
/touchpad_selection.html
文件，如使用手冊、API 函數手冊等。
ftp://ftp.icpdas.com/pub/cd/touchpad/document/chinese/
免費的開發軟體，HMIWorks (版本 2.09.15 或以上版本)：
ftp://ftp.icpdas.com/pub/cd/touchpad/setup/
如果您有什麼問題，歡迎來信連繫。
電子郵件：ser[email protected]
Other manuals for VPD-173N
1
This manual suits for next models
1
Table of contents
Other ICP DAS USA Touchscreen manuals
Popular Touchscreen manuals by other brands
Elecro Engineering
Elecro Engineering Poolsmart Plus Installation & operating manual
Johnson Controls
Johnson Controls IQ4 HUB installation manual
Elo TouchSystems
Elo TouchSystems ET2270L user manual
Elo TouchSystems
Elo TouchSystems ET1002L user manual
Elo TouchSystems
Elo TouchSystems 3201L user manual
Duratec
Duratec S15 user manual
