IBM TotalStorage NAS 100 User manual
IBM TotalStorage NAS 100
Rack Installation Instructions
IBM TotalStorage NAS 100
Rack Installation Instructions
First Edition (August 2002)
© Copyright International Business Machines Corporation 2002. All rights reserved.
US Government Users Restricted Rights – Use, duplication or disclosure restricted by GSA ADP Schedule Contract
with IBM Corp.
IBM TotalStorage
™
NAS 100 Rack Installation Instructions
Checking the rack installation kit
Items that you find in the kit:
vTwo telescopic slide rails
vFour brackets
vTwo mounting ears
vOne cable spiral wrap and eight cable ties
vAssorted hardware, including cage nuts, clip nuts, screws, nuts, and washers
vOne Rack Installation Instructions (this manual)
Items that you provide:
vOne Phillips #2 screwdriver
vOne flat-blade screwdriver (if you are using cage nuts)
vOne nutdriver or pair of pliers
© Copyright IBM Corp. 2002 1
Attaching the brackets
The following procedure explains how to attach the brackets to the telescopic slide
rails.
1. Extend the inner server slide rail as far as it will go.
2. Pull the white spring tab on the server slide rail towards its open end and
remove the server slide rail. Set it aside for attaching to the NAS 100 later.
1 Server slide rail
2 Spring tab
3 Telescopic slide rail
1
2
3
2NAS 100 Rack Installation Instructions
3. Attach the first bracket to the front end (the white end) of the telescopic slide
rail:
a. Locate the alignment screw hole on the front end of the outer telescopic
slide rail and align the bracket with it. The alignment screw hole establishes
where each screw will go in relation to the bracket. For most installations,
the alignment screw hole and bracket alignment will be the one illustrated in
the following figure.
1 Alignment screw hole
2 Bracket
3 Outer telescopic slide rail
Note: You will have to slide the inner ball-bearing slide rail and the inner
telescopic slide rail back and forth to align the oval cutout with the
screw hole so that you can insert the screw.
b. Insert an M4 screw through the bracket and in the alignment screw hole,
fasten a washer and an M4 nut to it, and firmly tighten them. Repeat this
step with three more screws in the remaining holes.
4. Extend the slide rails fully.
A
A
1
2
3
IBM TotalStorage
™
NAS 100 Rack Installation Instructions 3
5. Loosely attach the next bracket to the back end of the telescopic slide rail with
four more M4 screws, washers, and nuts, as shown in the following figure.
1 Telescopic slide rail
2 Bracket
Note: Do not completely tighten these screws until you install the slide rail into
the rack. This will make attaching the slide rail to the rack much easier.
After the slide rail is attached to the rack, you can tighten the screws on
the back bracket.
6. Hold the slide rails with the attached brackets up to the rack and check that the
slide rails and brackets will fit in the rack. Make any necessary adjustments to
the back end of the slide rail and its bracket.
7. Repeat this process with the other telescopic slide rail and brackets.
Note: Make sure that you install the screws in the other telescopic slide rail in
exactly the same places that you installed them in the first telescopic
slide rail.
1
2
4NAS 100 Rack Installation Instructions
Mounting the slide rails on the rack
The following procedure explains how to attach the telescopic slide rails to the rack.
1. Determine where on the rack you want to mount the NAS 100.
2. Depending on your rack type, use a screwdriver to insert the cage nuts or slide
the clip nuts into the appropriate holes. You will install two nuts on each side of
the back of the rack and three nuts on each side of the front of the rack (the top
nut is used for the mounting ear on the front of the NAS 100).
Note: Make sure that you insert each of the bottom nuts at the same height on
the rack so that the installed NAS 100 will be level.
1 Cage or clip (shown) nut
2 Front bracket
3 Back bracket
4 Left/right front mounting template
5 Left/right back mounting template
1
2
3
45
IBM TotalStorage
™
NAS 100 Rack Installation Instructions 5
3. Secure the front end of the slide rail to the front of the rack with three M6
screws.
4. Secure the back end of the slide rail to the back of the rack with two M6
screws.
5. Tighten the rear bracket M4 screws of the telescopic slide rail.
6. Repeat this procedure with the other telescopic slide rail and brackets.
6NAS 100 Rack Installation Instructions
Table of contents
Other IBM Storage manuals
IBM
IBM DS3500 User manual
IBM
IBM Travelstar 15GN User manual
IBM
IBM 1 GB Microdrive Storage Card User manual
IBM
IBM XIV Gen3 Series Technical manual
IBM
IBM FlashSystem 9150 Manual
IBM
IBM FlashSystem 710 User manual
IBM
IBM Storwize V5000 Gen2 User manual
IBM
IBM DMDM-10340 User manual
IBM
IBM SAN768B-2 User manual
IBM
IBM Storwize V7000 User manual
IBM
IBM N3240 Manual
IBM
IBM SAN Volume Controller Owner's manual
IBM
IBM Travelstar 10E Operating instructions
IBM
IBM 7212 102 User manual
IBM
IBM IC35L040AVVN07-0 - 40GB IDE Deskstar 120GXP 7200RPM UATA-100... User manual
IBM
IBM Slicestor 2212A User manual
IBM
IBM Ultrastar 36Z15 User manual
IBM
IBM FlashSystem 820 User manual
IBM
IBM 4002-C2A User manual
IBM
IBM 7212 Model 102 User manual
