I-Tech Clip IIIs User manual
(Cover)
i.Tech Clip IIIs
User Guide
(Page 0)
Contents
Bluetooth Buzzer Clip Headset……………..………………………………………2
Getting Started………………..……………..………………………………………3
Charging Your Headset…………………………………………………………….4-5
Nominal Charging Time…………………………………………………………5
Talk & Standby Time………………………………………………………….5
Low Battery……………………………………………………………………...5
Turning Your Headset On and Off…………………………………………………….6
Turning the Built-in Buzzer On and Off………………………………………………6
Pairing Your Headset………..………………………………………………………7-8
Using Your Headset………………………………………………………………9-10
Answering a Call…………………………………………………………………9
Answering a Call when Listening to Stereo Audio………………………………9
Ending a Call……………………………………………………………………..9
Rejecting a Call…………………………………………………………………..9
Dialing from Your Mobile Handset……………………………………………...9
Voice Dialing from Your Headset……………………………………………....10
Last Number Redialing from Your Headset……………………………………10
Listening to Stereo Audio fromYour PC………………………………………..10
Adjusting the Volume………………………………………………………………...11
Resetting / Removing the Pairing …………………………………………………...11
Care and Maintenance……………………………………………………………12-13
Safety Information……………………………………………………………………14
Troubleshooting……………………………………………………...……………….15
Product Specifications………………………………………………………………..16
(Page 1)
Bluetooth Buzzer Clip Headset Overview
Fig. 1
Getting Started
To use your i.Tech Clip IIIs headset (“the headset”), please follow these simple steps:
Charge your headset
Pair your headset with a Bluetooth-enabled mobile handset
Multifunction
Button(MFB)
Earpiece
Built-in rechargeable battery
Earpiece Jet and
removable earpiece for
Stereo
Charging SocketMicrophone
Vo l u m e
Dual LED
Built-in
Buzzer
Page 2
Wearing Your i.Tech Clip IIIs Headset as a Mono Headset
Page 3
Charging Your Headset
Fig. 4
The Headset comes with a built-in rechargeable battery. Prior to using the headset, it
is recommendable to charge the battery fully for the first time.
Page 5
Charging Your Headset
Connect the charger to an AC wall outlet and the charger plug to the headset’s
charging socket (fig.4). The LED will be red while charging.
IMPORTANT Charging indication will be delayed for a few seconds if the
headset has not been used for a long time or the battery is drained.
Nominal Charging Time
Charging the battery fully is normally within 3 hours. When the battery is fully
charged, the LED will turn blue and remains on for 30 minutes. Disconnect the
charger from AC wall outlet and the headset. Press and hold the MFB (fig.1) for 2
seconds to turn the headset on, please refer to “Turning Your Headset On and Off” on
the next page.
Talk & Standby Time
The fully charged battery offers up to 6 hours talk time and up to 150 hours standby
time. When no calls are in progress, the headset remains turned on in standby mode.
Low Battery
When the headset is on and the battery becomes low, the LED flashes red and the
headset emits a beep every 1 minute. Please recharge the battery as described above.
Page 6
Turning Your Headset On and Off
Turning On the Headset
Press and hold the MFB for 2 seconds until you hear a short beep. The LED will
flash blue.
IMPORTANT Press the MFB again each time you turn on the headset to
reactivate pairing so that the connection between the headset and the mobile
handset is resumed. For pairing, please refer to “Pairing Your Headset” on page
7-8.
Turning Off the Headset
Press and hold the MFB for 3 seconds until you hear a long beep. The LED flash
stops.
IMPORTANT To disconnect the Bluetooth connection, please firstly turn of
your headset by pressing the MFB key.
Turning the Built-in Buzzer On and Off
Turning On the Built-in Buzzer
Press and hold the Volume + for 2 seconds until you hear a long beep. The LED
flashes blue.
NOTE The built-in buzzer is set to “ON” when shipped.
Turning off the Built-in Buzzer
Press and hold the Volume – for 2 seconds until you hear 2 short beeps. The LED
flashes red. Now, when there is an incoming call, the ringing tone can be heard
through the earphone only.
Page 7
Pairing Your Headset
Prior to using your Headset for the first time, you must pair it with a
Bluetooth-enabled mobile handset.
The information on the next page describes pairing instruction for typical
Bluetooth-enabled mobile handset. Headset pairing procedure is subject to different
models of mobile handsets.
Page 8
Pairing Your Headset
1. Place the headset and the mobile handset where they are easily viewable by no
more than 1 meter apart.
2. Ensure the headset is OFF.
3. Press and hold the MFB until the headset LED alternately flashes blue and red.
4. Activate your mobile handset’s Bluetooth function by referring to your mobile
handset user guide for details.
5. Set the mobile handset to search for Bluetooth devices within about 1 meter as
instructed in the mobile handset user guide and select “i.Tech Clip IIIs” from the
list.
6. Enter the preprogrammed passkey “8888” and press “OK” to pair your headset
and mobile handset. When the pairing is complete, the headset LED will flash
blue rapidly for 5 times followed by a long beep.
7. Go back to your mobile handset’s main menu. For certain mobile handset models,
a headset icon will be shown on the screen. You should now be able to make and
receive calls using your headset.
IMPORTANT If the pairing cannot be completed within 2 minutes while the
pairing mode is activated, the headset LED flashes purple red with 3 beeps and
the headset is turned off. Please repeat Steps 2 to 7 to pair the headset and the
mobile handset again.
Page 9
Using Your Headset
Answering a Call
When there is an incoming call, you will hear ringing through the earphone and the
built-in buzzer. Press the MFB to accept the call or answer the call via your mobile
handset in the normal way.
If you want to stop the buzzer from ringing, press the Volume Key once. You now
only hear the ringing tone through the earphone.
Answering a Call when Listening to Stereo Audio
Press the MFB once to answer the call and when finished, press the MFB once to
resume stereo audio.
If the other party you are speaking to ends the call, stereo audio will automatically
resume without having to pressing the MFB.
NOTE To receive stereo audio from your mobile handset or PDA, please make
sure they support the Bluetooth A2DP profile.
Ending a Call
Press the MFB to end your call or end the call via your mobile handset in the normal
way.
Rejecting a Call
To reject an incoming call during ringing of the headset, press and hold the Volu me
Key for 2 seconds until you hear 2 beeps.
Dialing from Your Mobile Handset
Simply make calls on your mobile handset in the normal way.
Table of contents
Other I-Tech Headset manuals
