Hyundai H-CCR8104F User manual

USB/SD-МЕДИАПЛЕЕРUSB/SD MEDIA PLAYERРуководство по эксплуатации Instruction manualH-CCR8104F

Contents2Dear customer!Thank you for purchasing our product. For safety, it is strongly recommended to read this manual carefully before connecting, operating and/or adjusting the product and keep the manual for reference in the future.111111111111121212Table of contents Before you start Utilization of the product Important safeguardsInstallation/ConnectionInstallationGeneral notes1. DIN front-mount (Method A)Trim frame installation2. DIN rear-mount (Method B)Dismantling the unitConnectionConnection diagramUsing the ISO ConnectorOperationControl elementsLCD layoutGeneral operationsTurning on/offMode selectionVolume controlMute functionPreset equalizer modesClockAUX inputRadio operationsBand selectManual/Automatic tuningStoring and recalling stationsUSB/SD/MMC operationsConnecting a USB/memory cardPlaybackTrack selectFast forward/rewind233344444456668899999991010101010101111111111PauseIntro playbackRepeatRandomGeneral informationTroubleshooting guideCleaning the unit body AccessoriesSpecification

Before you start3If you want to dispose this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery and recycling.Please contact your local authorities for the correct method of disposal. By doing so, you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential negative effects on the environment and human health.Utilization of the productImportant safeguards• Read carefully through the manual to familiarize yourself with this unit.• Keep this manual handy as a reference for operating procedures and precautions. Do not allow persons who have not read through this manual to use this unit.• Do not allow this unit to come into contact with liquids. Electrical shock could result. Also, damage to this unit, smoke, and overheating could result from contact with liquids or dust. Protect this unit from moisture.• Make sure that foreign objects do not get inside the unit; they may cause malfunctions, or create safety hazards such as electrical shock or laser beam exposure.• The beginning of operation is the moment of the unit installation. Before use the device in winter it is recommended to heat up the passenger compartment during 20 seconds or to the operation temperature.• Using the unit with the temperature that goes beyond the operation temperature greatly decreases the operation resource of the screen and other components of the unit and can result in an outage.• Disconnect the vehicle’s negative battery terminal while mounting and connecting the unit.• The unit is designed for negative terminal of the battery, which is connected to the vehicle metal. Please ensure it before installation.• When replacing the fuse, be sure to use one with an identical amperage rating. Using a fuse with a higher amperage rating may cause serious damage to the unit.• Do not allow the speaker wires to be shorted together when the unit is switched on. Otherwise it may overload or burn out the power amplifier.• Make sure you disconnect the power supply and aerial if you will not be using the system for a long period or during a thunderstorm.• Make sure you disconnect the power supply if the system appears to be working incorrectly, is making an unusual sound, has a strange smell, has smoke emitting from it or liquids have got inside it. Let a qualified

Installation/Connection4technician check the system.• Always keep the volume low enough so that you can hear sounds from outside the vehicle.• Should this product fail to operate properly, contact your dealer or nearest service center.InstallationGeneral notes• Choose the mounting location where the unit will not interfere with the normal driving function of the driver.• Before finally installing the unit, connect the wiring and make sure that the unit works properly.• Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle.• Install the unit where it does not get in the driver’s way and cannot injure the passenger if there is a sudden stop, like an emergency stop.• Avoid installing the unit where it would be subject to high temperature, such as from direct sunlight, or from hot air, from the heater, or where it would be subject to dust, dirt or excessive vibration.DIN front-mount (Method A)1. Install the sleeve into the dashboard; ensure it is installed with the correct side and there are no obstacles (wires, dashboard elements, etc) for the unit installation.2. After installing the sleeve into the dashboard, bend tabs fitting to the size of the dashboard to fix the sleeve in place.3. Make the necessary wire connections. Ensure the connections are correct.4. Install the unit into the sleeve until the side locks are fixed.21182531. Dashboard2. Sleeve tab to bendTrim frame installationTo install the trim frame, press it to the unit body and push it to fix it in place. This should be done before installing the front panel; otherwise you are not able to install the trim frame.DIN rear-mount (Method B)For this method, use the screw holes in the lateral sides of the unit. Fix the unit with the help of the factory radio mounting brackets.1. Select a position in which the screw holes of the brackets (3) are aligned with the screw holes in the unit body, and screw in two screws (2) in each side.2. Screw.3. Factory radio mounting brackets.4. Vehicle dashboard.5. Lock (remove this part).

Installation/Connection5225543 The outer trim frame and mounting sleeve are not used for method of installation.Dismantling the unita – Trim frameb – Frame uninstall directionc – Release key insertioncba1. Switch off the unit and detach the front panel.2. Insert your fingers into the groove in the front side of the trim frame (apply some effort to detach the frame). Pull the frame to detach it.3. Insert the supplied release keys into the both sides of the unit body to click, as shown in the picture. To extract the unit from the dashboard, pull the release keys or the unit body to pull it out.

Installation/Connection6ConnectionConnection diagramRCA output left (white)AntennajackRCA output right (red)ISO connectorFuse (5 A)Using the ISO Connector1. If your car is equipped with the ISO connector, then connect the ISO connectors as illustrated. 2. For connections without the ISO connectors, check the wiring in the vehicle carefully before connecting, incorrect connection may cause serious damage to this unit. Cut the connector, connect the colored leads of the power cord to the car battery as shown in the color code table below for speaker and power cable connections.

Installation/Connection7LocationFunctionConnector AConnector B1Rear right (+) - Purple-2Rear right (-) - Purple-Black-3Front right (+) - Grey-4Front right (-) - Grey-BlackBattery +12V/Yellow5Front left (+) - WhitePower antenna/Blue-White6Front left (-) - White-Black-7Rear left (+) - GreenIgnition/Red8Rear left (-) - Green-BlackGround/Black Power antenna wire is intended for power supply of the antenna and for remote control of an additional amplifier.

Operation8Control elements1. PWR/MOD button2. / buttons3. VOLUME knob/SELECT button4. APS button5. MUT/LUD button. 6. Display7. USB port8. SD card slot9. BND/CLK button10. RESET button (hole)11. 1/ button12. 2/INT button13. 3/RPT button14. 4/RDM button15. 5/ button16. 6/ button17. AUX in1234567891011121314151617

Operation9LCD layout1. Radio band indicator2. Digit display (frequency, track time, etc.)3. FM frequency4. Signal indicator5. Not active6. SD playback indicator7. USB playback indicator8. Stereo signal reception indicator9. Mute indicator10. Intro mode on11. Repeat mode on12. Random playback on13. Not active14. Signal indicatorGeneral operationsTurning the unit on/offPress PWR/MOD button to turn the unit on. Press and hold the button again to turn the unit off.Mode selectionPress PWR/MOD button repeatedly to select between Radio, auxiliary input, USB or Memory Card modes. Modes of operation are indicated on the display. Memory card and USB modes are not available unless a memory card or USB device is connected.Volume controlAdjust volume by rotating VOLUME knob.Mute functionPress MUT/LUD button to switch off the sound; press it again or rotate VOLUME knob to resume the sound.LoudnessPress and hold MUT/LUD button to select loudness ON or OFF (when on, loudness indicator will be displayed). Activating this feature will enhance bass and treble frequencies when listening to music at low volumes.

1234567891011121314

Operation10Audio parameter settingPress SELECT button repeatedly to select a parameter: BAS (bass) => TRE (treble) => BAL (balance) => FAD (fader) => LOUD ON/OFF => EQ (equalizer) => ST/MONO (stereo or mono). Rotate VOLUME knob to adjust each mode:• Bass/Treble: from -7 to 7;• Balance: L07 (left) to R07 (right);• Fader: from R07 (rear) to F07 (front).• Loudness: see “Loudness” paragraph above.• EQ: select ROCK/POP/CLASS/JAZZ equalizer mode. When equalizer is in any mode except OFF, bass and treble are not adjustable.Preset equalizer modesIN USB/SD playback mode press SELECT button repeatedly until ROCK/POP/CLASS or JAZZ equalizer mode is displayed. Rotate VOLUME regulator to select equalizer mode.ClockPress and hold BND/CLK button to display the time on the screen. Then press and hold this button again; the hour indication will blink. Rotate VOLUME regulator to adjust hours; press BND/CLK button to go to minutes; rotate VOLUME regulator to adjust minutes. To confirm the adjustment, press BND/CLK button or leave the unit idle for several seconds.AUX inputAUX-in jack is intended for connecting an external audio equipment to amplify the sound. If connection is made correctly, the audio signal from the external source will be translated through the acoustics of the head unit. This enables to adjust the volume and quality of the sounding. For example, you can connect an MP3-player to listen to tracks using the car acoustic system.Radio operationsBand selectIn Radio mode press BND/CLK button to select a radio band: F1 (FM1), F2 (FM2), F3 (FM3). 6 stations can be saved in each band.Manual/automatical tuning• Press / buttons repeatedly to adjust the needed frequency manually.• Press and hold or button. The radio will seek to the next down or up strong and clear frequency station.Storing and recalling stations• Press and hold APS button for more than 2 seconds to automatically find and store 6 strongest stations in the current band.• After 6 strongest stations are saved, press APS button; scanning of all stored stations will begin.• Press buttons 1-6 to select saved channels. If you want to save a new station in a preset position, select corresponding station number with 1-6 buttons. Then tune to the needed frequency as described in “Manual/automatical tuning“ above and press