Hunter Norway 20490 Instruction manual

Type 2 ModelsType 2 ModelsType 2 Models

Form# 45025-01

20081119

For Your Records and

Warranty Assistance

For reference, also attach your receipt or a copy

of your receipt to the manual.

__________________________________________

Model Name

__________________________________________

Model No.

__________________________________________

Date Purchased

__________________________________________

Where Purchased

Norway

20490

English Español

Owner’s Guide and Installation Manual

45025-01 • 11/19/08 • Hunter Fan Company

Your new Hunter® ceiling fan is an addition to your home or oce that

will provide comfort and performance for many years. is installation

and operation manual gives you complete instructions for installing

and operating your fan.

We are proud of our work. We appreciate the opportunity to supply

you with the best ceiling fan available anywhere in the world.

Before installing your fan, for your records and warranty assistance,

record information from the carton and Hunter nameplate label

(located on the top of the fan motor housing).

Cautions and Warnings

•READ THIS ENTIRE MANUAL CAREFULLY BEFORE BEGINNING

INSTALLATION. SAVE THESE INSTRUCTIONS.

• Use only Hunter replacement parts.

• To reduce the risk of personal injury, attach the fan directly to the

support structure of the building according to these instructions,

and use only the hardware supplied.

• To avoid possible electrical shock, before installing your fan,

disconnect the power by turning o the circuit breakers to the

outlet box and associated wall switch location. If you cannot lock

the circuit breakers in the o position, securely fasten a prominent

warning device, such as a tag, to the service panel.

• All wiring must be in accordance with national and local electrical

codes and ANSI/NFPA 70. If you are unfamiliar with wiring, use a

qualied electrician.

• To reduce the risk of personal injury, do not bend the blade

attachment system when installing, balancing, or cleaning the fan.

Never insert foreign objects between rotating fan blades.

• To reduce the risk of re, electrical shock, or motor damage, do not

use a solid-state speed control with this fan. Use only Hunter speed

controls.

Welcome

Table Of Contents

1 • Getting Ready......................4

2 • Installing the Hanger Bracket . . . . . . . 5

3 • Assembling and Hanging the Fan ...6

4 •Wiring the Fan......................8

5 • Installing the Canopy and Canopy

Trim Ring .........................9

6 • Assembling the Blades . . . . . . . . . . . . .10

7 • Completing Your Installation With a

Bowl Light Fixture . . . . . . . . . . . . . . . .11

8 • Operating and Cleaning Your Ceiling

Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

9 • Troubleshooting . . . . . . . . . . . . . . . . . 14

45025-01 • 11/19/08 • Hunter Fan Company

Understanding Mounting and Installer’s Choice®

Hunter’s patented 3-position mounting system provides you maximum

installation exibility and ease. You can install your Hunter fan in one

of three ways, depending on ceiling height and your preference: Low

Prole, Standard, or Angled mounting. e steps in this manual include

instructions for all three Installer’s Choice mounting methods.

Considering Optional Accessories

Consider using Hunter’s optional accessories, including a wall-mounted

or remote speed control. To install and use the accessories, follow

the instructions included with each product. For quiet and optimum

performance of your Hunter fan, use only Hunter speed controls.

For ceilings higher than 8 feet, you can purchase

Hunter extension downrods. All Hunter fans use

sturdy 3/4” diameter pipe to assure stability and

wobble-free performance.

Standard Mounting hangs from the

ceiling by a downrod (included).

Angled Mounting recommended for a

vaulted or angled ceiling

Support Brace

Standard

Mounting

Style

Ceiling

Outlet Box

Support Brace

Ceiling

Outlet Box

Angled

Mounting

Style

Low Proﬁle Mounting ts close to the

ceiling, recommended for ceilings less

than 8 feet high

Support Brace

Low Prole

Mounting

Style

Ceiling

Outlet Box

CAUTION: To

reduce the risk of

personal injury, attach

the fan directly to the

support structure of

the building according

to these instructions,

and use only the

hardware supplied.

Installer’s Choice and Optional Accessories

45025-01 • 11/19/08 • Hunter Fan Company

To install a ceiling fan, be sure you can do the following:

• Locate the ceiling joist or other suitable support in ceiling.

• Drill holes for and install wood screws.

• Identify and connect electrical wires.

• Lift 40 pounds.

If you need help installing the fan, your Hunter fan dealer can direct

you to a licensed installer or electrician.

Gathering the Tools

You will need the following tools for installing the fan:

• Electric drill with 9/64” bit

• Standard screwdriver (magnetic tip recommended)

• Phillips-head screwdriver (magnetic tip recommended)

• Wrench or pliers

• Ladder (height dependent upon installation site)

Checking Your Fan Parts

Carefully unpack your fan to avoid damage to the fan parts. Refer to

the included Parts Guide. Check for any shipping damage to the motor

or fan blades. If any parts are missing or damaged, contact your Hunter

dealer or call Hunter Technical Support Department at 888-830-1326.

Preparing the Fan Site

Before you begin installing the fan, follow all the instructions in

the pullout sheet called “Preparing the Fan Site.” Proper ceiling fan

location and attachment to the building structure are essential for

safety, reliable operation, maximum eciency, and energy savings.

Installing Multiple Fans?

If you are installing more than

one fan, keep the fan blades and

blade irons (if applicable) in sets,

as they were shipped.

1 • Getting Ready

45025-01 • 11/19/08 • Hunter Fan Company

2-1. Drill two pilot holes into the wood support structure through the

outermost holes in the outlet box. e pilot holes should be 9/64”

in diameter.

Note: Your fan comes with four pre-installed neoprene noise

isolators.

2-2. read the lead wires from the outlet box down through the hole

in the middle of the hanger bracket.

2-3. Align the slotted holes in the hanger bracket with the pilot holes

you drilled in the wood support structure. For proper alignment

use slotted holes directly across from each other. If you are

installing the fan on an ANGLED ceiling, be sure to orient the

hanger bracket as shown in Illustration 2-3 (left or right view).

Note: e isolators should be ush against the ceiling.

2-4. Place a at washer on each of the two 3” screws and pass the

screws through the slotted holes in the hanger bracket into the

pilot holes you drilled.

Tighten the screws into the 9/64” pilot holes; do not use lubricants

on the screws. Do not over tighten.

Flat Washer

3” Screw

Steps 2-2 – 2-4

Hanger

Bracket

Isolator

Step 2-3 (Angled Ceiling Only)

Ceiling Peak Ceiling Peak

Large

Opening Large

Opening

LEFT RIGHT

2 • Installing the Hanger Bracket

45025-01 • 11/19/08 • Hunter Fan Company

You can assemble your fan for standard or angled mounting as shown

in steps 3-1 – 3-3. For low proﬁle mounting (ceilings less than 8 feet

high), go to steps 3-6 – 3-9 on the next page.

3-1. To assemble fan to hang down from a at or angled ceiling, place

the canopy and canopy trim ring around the adapter so that they

rest on the fan assembly.

3-2. Feed the wires from the fan through the downrod.

Note: Make sure all the wires are on the same side of the metal

dowel pin inside the dowrod.

3-3. Using the provided Allen wrench, loosen the setscrew on the

adapter to install the pipe and ball assembly. Note: When the

pipe and ball assembly is fully installed, 2-3 threads on the pipe

will still be visible; this is normal. Use the Allen wrench to securely

retighten the setscrew.

CAUTION: e adapter has a special coating on the threads. Do

not remove this coating; the coating prevents the downrod from

unscrewing. Once assembled, do not remove the downrod.

WARNING: Do not carry or lift fan by canopy.

3-4. Raise the fan and place the ball into the hanger bracket.

3-5. Align the notch on the ball with the indent in the hanger bracket.

(Rotate the fan until you hear the notch pop into place.)

Go to 4 • Wiring the Fan.

WARNING: Fan may fall if not assembled as directed in these

installation instructions.

Steps 3-4 – 3-5

Indent

Steps 3-1 – 3-3

Downrod

Canopy

Trim

Ring

Setscrew

Adapter

Allen Wrench

3 • Assembling and Hanging the Fan

45025-01 • 11/19/08 • Hunter Fan Company

3 • Assembling and Hanging the Fan (Low Profile Only)

You can assemble your fan for standard or angled mounting as shown

in steps 3-1 – 3-3 on the previous page. For low proﬁle mounting

(ceilings less than 8 feet high), see steps 3-6 – 3-10 on this page.

3-6. Remove the screws from the hanger ball bracket.

3-7. Place the low prole washer from the parts sack into the canopy.

3-8. Place the canopy trim ring and canopy with washer on top of the

fan assembly.

3-9. Align the screw holes in the washer with the holes in the adapter.

Assemble securely with three #8-32 x 3/4” screws.

3-10. Raise the fan and place the hook on the hanger bracket through

the round hole in the rim of the canopy.

WARNING: Fan may fall if not assembled as directed in these

installation instructions.

Step 3-10

Step 3-7 (Detail)

Low Prole Washer

(Not Actual Size)

Steps 3-8 – 3-9

Low Prole Washer

Canopy

Trim Ring

Adapter

#8-32 x 3/4” Screw

Step 3-6

45025-01 • 11/19/08 • Hunter Fan Company

All wiring must be in accordance with national and local electrical

codes and ANSI/NFPA 70. If you are unfamiliar with wiring, use a

qualiﬁed electrician.

Wall switches are not included. Select an acceptable general-use switch

in accordance with national and local electrical codes.

4-1. Before attempting installation, make sure the power is still o.

4-2. To connect the wires, hold the bare metal leads together and place

a wire connector over them, then twist clockwise until tight. For

all these connections use the wire connectors provided.

4-3. Connect the bare or green ground wire (grounded) from the

ceiling to the green ground wire (grounded) from the ceiling plate

and the green ground wire from the fan.

4-4. Connect the white wire (ungrounded) from the ceiling to the

white wire (ungrounded) from the fan.

4-5. Connect the remaining wires as follows:

Dual Switch Wiring:

• e black wire (ungrounded) from the ceiling to the black wire

(ungrounded) from the fan

• e black/white wire (ungrounded) from the fan to the wire

(ungrounded) for the wall switch

Single Switch Wiring:

• e black wire (ungrounded) from the ceiling to the black

(ungrounded) and the black/white wire (ungrounded) from

the fan

CAUTION: Be sure no bare wire or wire strands are visible after

making connections.

4-6. Turn the wire connectors upward and push them carefully back

through the ceiling plate into the outlet box.

4-7. Spread the wires apart, with the grounded wires on one side of

the outlet box and the ungrounded wires on the other side of the

outlet box.

Wire

Connector

4 •Wiring the Fan

45025-01 • 11/19/08 • Hunter Fan Company

5-1. Partially install two canopy screws (about 2 full turns) in the

hanger bracket.

5-2. Raise the canopy over the hanger bracket. Align partially installed

screws with key slots in canopy.

5-3. Twist canopy clockwise to secure.

5-4. Install third & fourth canopy screw in round hole on canopy.

Securely tighten all four screws.

5-5. Using both hands, push the canopy trim ring up to the top of the

canopy.

5-6. Twist canopy trim ring clockwise to secure the canopy.

Should you need to remove the canopy

trim ring, follow these steps:

1. Twist canopy trim ring counter

clockwise until it releases from

canopy.

Steps 5-1 – 5-2

Canopy Trim

Ring

Canopy

Hanger Bracket

Step 5-3

Canopy

Screw

Step 5-4

Step 5-5

5 • Installing the Canopy and Canopy Trim Ring

45025-01 • 11/19/08 • Hunter Fan Company

6-1. Attach each blade to a blade iron using three blade

assembly screws.

Blade Assembly

Screw

Blade Assembly

Screws

Step 6-1

6 • Assembling the Blades

Table of contents

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual

Litex Industries

Litex Industries E-CGL52CB5C1 installation guide

Lindab

Lindab LTDF installation instructions