Hubbell G040 Instruction Manual

3940 Dr. Martin Luther King Drive

St. Louis, MO 63113

P/N 00901216 FORM NO. K0304 R08/08 ECO-3-029-08 Page 1 of 3

INSTALLATION, OPERATION &

MAINTENANCE DATA SHEET

G040 PUSHBUTTON RESET OPERATORS FOR

CLASS II, GROUPS E, F, & G, & CLASS III HAZARDOUS

LOCATIONS

G040 PUSHBUTTON RESET OPERATORS

CAUTION:

Before installing, make sure you are compliant with area classications, failure to do so may result in bodily injury,

death and property damage. Do not attempt installation until you are familiar with the following procedures. All

installation must comply with the applicable Electrical Code.

Make sure that the circuit is de-energized before starting installation or maintenance.

Verify that the installation is grounded. Failure to ground will create electrical shock hazards, which can cause

serious injury and or death.

Technical information, advice and recommendations contained in these documents is based upon information

that Killark believes to be reliable. All the information and advice contained in these documents is intended for

use only by persons having been trained and possessing the requisite skill and know-how and to be used by

such persons only at their own discretion and risk. The nature of these instructions is informative only and does

not cover all of the details, variations or combinations in which this equipment may be used, its storage, delivery,

installation, check out, safe operation and maintenance. Since conditions of use of the product are outside of the

care, custody and control of Killark, the purchaser should determine the suitability of the product for his intended

use, and assumes all risk and liability whatsoever in connection therewith.

3940 Dr. Martin Luther King Drive

St. Louis, MO 63113

P/N 00901216 FORM NO. K0304 R08/08 ECO-3-029-08 Page 2 of 3

These pushbutton operators are designed for

enclosures which meet the requirements of Article 500

of the National Electrical Code. GO40 devices are to

be mounted in enclosures with walls up to ½” thick.

1. DIRECTIONS FOR INSTALLATION

Be sure to turn OFF the supplying circuit before

beginning installation

1. Using the installation drawings as a guide, drill

and tap a ¾” - 14 NPSM - 2A hole in the

enclosure cover. The hole must be located so

that a at area is available to tighten the locknut

on the inside of the cover and enough room

is allowed for mounting the nameplate on the

outside. For proper electrical clearance, these

devices should be mounted on 2 1/2” centers

and 1 3/4” from any vertical wall.

2. Remove the locknuts and spacer (if so equipped)

from the assembly, place the nameplate

in position on the cover and thread the

assembly into the cover tightening it against the

nameplate. If the optional trim locknut is used, it

must be threaded onto the body before installing

the body in the cover.

3. Tighten the assembly and secure it with the

locknut(s). (The assembly may be staked in

place, if desired).

4. Replace the spacer and/or reset plate (if so

equipped), close the cover and test the button

for operation.

NOTE: All installations must comply with

applicable local and/or National Electrical Code.

2. OPERATIONAL DATA

GO40 operators are designed to operate with

¾” maximum travel of the shaft. Various spacers

and extensions are available to facilitate proper

operation with most any type of equipment.

A protective boot is also available to cover the

pushbutton in wet areas.

3. MAINTENANCE DATA

“GO” Series Pushbutton Operators should be

periodically checked for damage and for proper

operation. The pushbutton shaft should be

lubricated occasionally to prevent binding.

Damaged or worn parts should be replaced

promptly to maintain safe operation. Refer to the

parts Drawing and to the Killark catalog for specic

replacement parts and part numbers.

3940 Dr. Martin Luther King Drive

St. Louis, MO 63113

P/N 00911850 FORM NO. KO687 R01/06 ECO-8-021-04 Page 3 of 3

Table of contents

Other Hubbell Lighting Equipment manuals

Hubbell

Hubbell homeSELECT RMS100 User manual

Hubbell

Hubbell Laredo LMC User manual

Hubbell

Hubbell M-7679 R-PAC User manual

Hubbell

Hubbell KILLARK VSQ Series Owner's manual

Hubbell

Hubbell KILLARK VEB Series Instruction Manual

Hubbell

Hubbell NXP2 Series User manual

Hubbell

Hubbell Prescolite LBSLEDA User manual

Hubbell

Hubbell DUAL LITE LN4X Series Owner's manual

Hubbell

Hubbell VSLT-UP User manual

Hubbell

Hubbell DUAL LITE EVE Series User manual

Hubbell

Hubbell Kim Lighting Lightvault LTV59 User manual

Hubbell

Hubbell WPH Series User manual

Hubbell

Hubbell Dual-Lite EVHC-BC Series Manual

Hubbell

Hubbell Dual Lite EV Series Manual

Hubbell

Hubbell Dual Lite EZ-2R Series Manual

Hubbell

Hubbell Litecontrol 22L Series User manual

Hubbell

Hubbell SAVVANO User manual

Hubbell

Hubbell Laredo LMC User manual

Hubbell

Hubbell ExpressLine Miniliter IV MHSY Series User manual

Hubbell

Hubbell KIM LIGHTING LIGHTVAULT LTV55 User manual

Hubbell

Hubbell Compass CU2SO User manual

Hubbell

Hubbell Dual-Lite DYNC C1D2 Series User manual

Hubbell

Hubbell PRS User manual

Hubbell

Hubbell LITEFRAME LC4 User manual

Popular Lighting Equipment manuals by other brands

Brizo

Brizo 8SP-MU-4 manual

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 installation instructions

IKEA

IKEA BJÖRKSPIREA manual

Laserworld

Laserworld Evolution Series ES-400RGB manual

Alien

Alien RG STAR user manual

EuroLite

EuroLite LED B-40 user manual

Qazqa

Qazqa Suplux SL 3 Black 103062 instruction manual

Commercial Electric

Commercial Electric 54568141 Use and care guide

CREE LIGHTING

CREE LIGHTING 304 Series installation instructions

Goobay

Goobay 49867 user manual

ECOMAN ITALIA

ECOMAN ITALIA LED T8 instruction manual

Alkalite

Alkalite Krypton KT-81 user manual

Clas Ohlson

Clas Ohlson GU10 manual

DTS

DTS DELTA 10 F user manual

ring

ring Solar Steplight manual

One Stop Gardens

One Stop Gardens 57696 Owner's manual & safety instructions

Chauvet DJ

Chauvet DJ COREpar UV120 ILS user manual

SIREM

SIREM Swimeo A2 instructions