Huawei UPS5000-H-1200K-NT User manual
1
Issue: 01
Part Number: 31500EKM
Date: 2020-07-15
UPS5000-H-1200 kVA Quick Guide
(100 kVA Power Modules)
1Overview
Model UPS5000-H-1200K-NT
Weight 1497 kg
Dimensions (H x W x D) 2200 mm x 1600 mm x 1000 mm
Copyright © Huawei Technologies Co., Ltd. 2020. All rights reserved.
1. Before installation, read the user manual carefully to get familiar with product information
and safety precautions.
2. Use insulated tools during installation and operation.
3. Only engineers certified by Huawei or its agents are allowed to install, commission, and
maintain the UPS. Otherwise, personal injury or equipment damage may occur, and the UPS
faults caused are beyond the warranty scope of Huawei.
Surge protective
devices (SPDs)
and SPD switches
Power modules
Surge protection boxes
Control module
Intelligent detection
board
Bypass control module
Bypass modules
2
A: Mounting holes on the channel steel
B: Mounting holes on the floor
Dimensions of the Cabinet Holes
Determining the UPS Installation Position
2.1
1. The UPS can be installed on the channel steel or floor. Determine the mounting hole positions
using a marking-off template (unit: mm), drill holes, and install expansion sleeves based on site
requirements.
2Installing the UPS
Recommended Channel Steel Dimensions
3
(A) Mounting holes on the channel steel: M12x60 bolts
(B) Mounting holes on the floor: M12x60 expansion bolts
2. Secure the UPS.
Bolts are not included.
3. Install anchor baffle plates.
4
3Installing Cables
UPS Cable Connection Reference
3.1
•Prepare cables away from the cabinets to prevent scraps from falling inside. Cable scraps
may ignite and cause personal injury or device damage.
•After cables have been installed, clean the cabinets in a timely manner. Keep the cabinets
and surrounding environment clean and tidy.
•You need to prepare terminals onsite. The stripped length of the copper wire should be the
same as that of the part of the terminal that covers the conductor.
The cabling route is for reference only. Connect cables based on site requirements.
Installing Cables and Copper Bars
3.2
Prepare wiring copper bars based on the following figures and current requirements.
Item
Specifications (A)
Mains input current
2229
Bypass input current
1823
Output current
1823
Battery input
Nominal battery discharge current
2632
Maximum battery discharge current
3185
•Copper bars need to be prepared for the mains input, bypass input, and output, and cannot be
directly connected using cables. (Huawei does not provide copper bars or connector boxes.)
•The battery input can be connected only using cables.
•The currents listed in the table are measured at a rated voltage of 380 V (line voltage). For
details, see the user manual.
5
Installing UPS Cables
3.2
Top view of the distance between copper bars on the top (unit: mm)
The areas marked by the line boxes are the
recommended areas for installing connector boxes
The area marked by the line
box is reserved for the dense
busway
Front view of the distance between copper bars on the top (unit: mm)
6
Copper bar specifications (unit: mm)
Copper Bar Positions
UPS
Output
Bypass Input
Battery
PE
Battery
Input Main
Input
7
1. Connect the equipotential ground point and the ground bar in the equipment room.
Ground bar in the
equipment room
2. (Optional) Remove the copper bars between the mains input and bypass input.
a) Remove the covers.
Perform this step only when the mains input and bypass input use different power sources.
The 16 mm2ground cable is recommended.
8
3. Install battery cables.
b) Remove the screws that secure the guide rail of the SPD.
c) Place the SPD on the horizontal plate (without removing the cables).
d) Remove the copper bars.
e) Reinstall the SPD.
Connect the ground cable of the
battery string or its BBB box to
the battery PE of the UPS or the
ground bar in the equipment
room based on the site survey.
9
6. Prepare and install a connector box based on site requirements. (For the hole size, see "Top
view of the distance between copper bars on the top.")
4. Install top supports and covers of the battery terminal protective covers.
5. Connect input and output busbars based on the top copper bar position diagram.
Port Description
Connection Method
Bolt Specifications
Bolt Length
Torque
Mains input/bypass
input/output/PE
Crimped DT terminals
M12
45 mm
47
N·m
10
4Verifying the Installation
1. Check that there is no foreign matter in the cabinets.
2. (Remove the paper protective film from the sealing putty.) After routing cables and verifying
cable connections, seal the gap between cables and the cabinet using sealing putty.
Sealing putty must be used as a whole and the gap can be sealed only from the top.
Paper
protective
film Sealing putty
7. Install a signal cable.
Other manuals for UPS5000-H-1200K-NT
2
Table of contents
Other Huawei UPS manuals
Huawei
Huawei UPS5000-S-880K-SM User manual
Huawei
Huawei UPS5000-A-H Series User manual
Huawei
Huawei PDU8000 Series User manual
Huawei
Huawei PowerCube 500 User manual
Huawei
Huawei UPS5000-S-400K-SM User manual
Huawei
Huawei UPS5000-S-1600KVA-FP User manual
Huawei
Huawei UPS5000-E Series User manual
Huawei
Huawei UPS5000-S200K-SM User manual
Huawei
Huawei PDU8000 Series User manual
Huawei
Huawei UPS5000-E Series User manual
Huawei
Huawei UPS5000-E-25K-SM User manual
Huawei
Huawei SmartLi Series User manual
Huawei
Huawei UPS5000-A series User manual
Huawei
Huawei UPS5000-E-400 kVA User manual
Huawei
Huawei UPS2000-G-3KRTL-V2 User manual
Huawei
Huawei UPS5000-A series User manual
Huawei
Huawei UPS2000-G-6KRTLL User manual
Huawei
Huawei UPS5000-E Series User manual
Huawei
Huawei UPS2000-H User manual
Huawei
Huawei UPS5000-E-180 kVA User manual
