Huawei BBU3900 User manual
HUAWEI TECHNOLOGIES Co., Ltd.
BBU3900
Installation Guide
Issue: 19
Date: 2011-01-20
1
Contents
Installation Tools…………………………………
Installation Scenarios……………………………
BBU Hardware……………………………………
Installation Procedure……………………………
Installing the BBU in the APM30………………
Installing the BBU in the APM30H(Ver.A) ……
Installing the BBU in the 19-Inch Rack…………
Installing the BBU in the TMC……………………
Installing the BBU in the PS4890 Cabinet……
Installing the BBU in the RRU3004 Rack………
Installing the IMB03 on the H-Shaped Stand…
Installing the RRU on the H-Shaped Stand …
Installing the BBU on the Wall…………………
Installing the BBU in the APM30H(Ver.B)……
Installing the BBU in the TMC11H(Ver.B)……
Installing the BBU in the
APM30H(Ver.B, +24V) ……………………………
Installing the BBU in the OMB …………………
BBU Hardware Installation Checklist…………
Powering On the BBU……………………………
Obtaining the ESN ………………………………
Appendix……………………………………………
Change History……………………………………
2
3
5
6
7
13
15
17
20
23
27
28
29
33
37
39
41
47
47
48
48
56
Copyright © Huawei Technologies Co., Ltd. 2011. All rights reserved.
2
Installation Tools
Measuring tape Phillips screwdriver (M3-M6) Flat-head screwdriver (M3-M6)
Adjustable wrench Socket wrench Hammer drill
ESD wrist strap Vacuum cleaner Wire stripper
Torque wrench Marking pen Level
RJ-45 crimping tool Multimeter
Power cable crimping tool Cable cutter ESD gloves
Rubber Mallet
3
Installation Scenarios
In the APM30/APM30H(Ver.A) In the PS4890
In the RRU3004 rackIn the TMC
In the 19-inch rack
The GTMU in this document is based on the first type of GTMU.
In the APM30H(Ver.B)
4
Installation Scenarios
In the TMC11H(Ver.B) In the APM30H (Ver.B, +24V)
On the wall In the OMB
5
BBU Hardware
1. Exterior of the BBU
2. Configuration Principles of the BBU Boards
Board Mandatory/
Optional Full Configuration Installation
Slot Remarks
GTMU Mandatory 1 S5 and S6 Can be installed only in S5 and S6.
UPEU Mandatory 2 S18 or S19 A single UPEU is preferentially configured
in the S19 slot.
FAN Mandatory 1 S16 Can be installed only in the S16 slot.
UTRP Optional 1 S0 or S4 Preferentially installed in the slot4.
UELP Optional 2 S0 or S4 A single UELP is preferentially configured
in the S4 slot.
UFLP Optional 2 S0 or S4 A single UELP is preferentially configured
in the S4 slot.
USCU Optional 1 S0 or S1 Preferentially installed in the S1 slot.
UEIU Optional 1 S18 Preferentially installed in the S18 slot.
zThe UELP and UFLP need to be optionally configured in the BBU or SLPU on site according to the field
requirements.
zUTRP is supported in V300R012 and later versions.
86 mm
(2U)
442mm
310mm
6
Installation Procedure
When the equipment is unpacked, it must be powered on in seven days. The maximum
duration of the power-off state of the equipment is 48 hours during maintenance.
7
Installing the BBU Case
a
Installing the BBU Cables
b
External power supply
External alarm device
Monitoring signal
cable
Alarm cable
E1/T1cable
CPRI signal cable
E1/T1 surge protection
transfer cable
Power cable
Cable connections of the BBU
External monitoring device
Installing the BBU in the APM30
BBU
M6 bolt
PDU
1. Install the mounting ears at both sides of
the BBU reversely.
2. Slide the BBU case into the cabinet.
FE/GE cable
FE/GE surge protection
transfer cable
8
Installing the BBU in the APM30
Winding pipe
Installing the BBU Cables
b
2. Install the CPRI optical cable.
The TX port on the BBU is connected to the RX port on the RRU.
The RX port on the BBU is connected to the TX port on the RRU.
Connect the OT terminal of the power cable to the LOAD3
terminal of the PDU, and then fix the 3V3 connector of the
power cable to the PWR port on the BBU.
1. Install BBU power cable.
The OT terminals of the power cable is to be made on site.
Optical module
Puller
a. Insert the optical module into the CPRI0,
CPRI1, CPRI2 CPRI3, CPRI4 or
CPRI5 port, and then turn outwards
the puller on the optical module.
b. Insert one end of the CPRI optical cable
into the optical module, and then lead
the CPRI optical cable out of the
cabinet along the right side of the
cabinet.
c. Wrap the fiber tail with the winding pipe.
LOAD3
NEG(-)
RNT(+)
PWR
The single-mode optical module is labeled "SM" and multi-mode optical module is labeled "MM“.
If the puller of an optical module is blue, the module is a single-mode optical module. If the puller of an optical
module is black or grey, the module is a multi-mode optical module.
Connect the fiber tails labeled 2A and 2B to one of the CPRI0 to CPRI5 ports on the
GTMU, and connect the fiber tails labeled 1A and 1B to the CPRI_W port on the RRU.
9
Installing the BBU in the APM30
b
4.3. Strip the jacket off the E1/T1 cable near the grounding point at the lower right
corner of the cabinet to expose the shielding layer
4.4. Thread the E1/T1 cable through the grounding clip. Then, tighten the screw on the
grounding clip to make the shielding layer of the E1/T1 cable in full contact with the
grounding clip. Finally, connect the PGND cable on the grounding clip to the ground bolt
of the APM30.
4.2. Fix the DB26 connector of the E1/T1 cable to the OUTSIDE port on the UELP.
3. Install the E1/T1 surge protection transfer cable.
4. Install the E1/T1 cable.
E1/T1 surge protection
transfer cable
4.1. Cabling the E1/T1 cable.
E1/T1cable
Shielding layer of
the E1/T1 cable
Shielding layer of the E1/T1
cable (25 mm)
Fix the DB25 connector of the E1/T1 surge protection transfer cable to the INSIDE
port on the UELP and the DB26 connector to the E1/T1 port on the GTMU.
Grounding
clip
Installing the BBU Cables
Before soldering the connectors to the E1/T1 cable, ensure that both ends of the E1 cable are
disconnected from any devices. In addition, all the connectors should be soldered to the cable.
Other manuals for BBU3900
5
Table of contents
Other Huawei Accessories manuals
Huawei
Huawei Airbridge DBS3900 User manual
Huawei
Huawei DTSU666-H User manual
Huawei
Huawei DTSU666-H User manual
Huawei
Huawei RRU3268 User manual
Huawei
Huawei RRU3804 User manual
Huawei
Huawei iSiteC BTS3601C User manual
Huawei
Huawei iSiteC BTS3601C User manual
Huawei
Huawei iSiteC BTS3601C User manual
Huawei
Huawei DBS3900 V300R008 Technical specifications
Huawei
Huawei RRU3201 Owner's manual
Huawei
Huawei Airbridge DBS3900 User manual
Huawei
Huawei RRU3201 User manual
Huawei
Huawei 02312PBL User manual
Huawei
Huawei 3900 Series User manual
Huawei
Huawei DTSU666-HW User manual
Huawei
Huawei Airbridge DBS3900 User manual
Huawei
Huawei FusionCol8000-E260 User manual
Huawei
Huawei NetCol5000-A021 User manual
Huawei
Huawei NetCol8000-C070 User manual
Huawei
Huawei NetCol5000-A025 User manual
