HP StorageWorks 2/16 - SAN Switch User manual

addendum

Printed in the U.S.A. March 2003

Product names mentioned herein may be trademarks of their respective companies as reflected by an associated

footnote. The information in this document is subject to change without notice.

This addendum only applies to the following documents:

HP StorageWorks SAN Switch 2/32 Installation Guide, Version 4.0.x

AA–RTQVB–TE (February 2003)

HP StorageWorks SAN Switch 2/16 Installation Guide, Version 3.0.x

AA–RR84B–TE (February 2003)

HP StorageWorks SAN Switch 2/8 Installation Guide, Version 3.0.x

AA–RSB6B–TE (February 2003)

hp StorageWorks

SAN switch universal rack mount

kit installation

Product Version: V3.0.x/V4.0.x

Pen-and-ink Changes

2 SAN Switch Universal Rack Mount Kit Installation Addendum

This addendum consists two parts:

■Pen-and-ink Changes—provides instructions for locating specific text and

either deleting text, replacing text with new text, or adding new text at a

specific location.

■Page Additions—identifies where to add a page at a specific place in the

document and recommends how to attach the replacement pages.

Note: If the changes within this addendum are not incorporated into the specified

documents and then used, problems might arise from using obsolete information.

Pen-and-ink Changes

There are no pen-and-ink changes in this addendum.

Page Additions

The following pages describe the installation of the SAN Switch 2/32, SAN

Switch 2/16, and SAN Switch 2/8 in an HP Series 9000 or comparable EIA rack,

or in an HP System/e rack using the SAN Switch Universal Rack Mount Kit, part

number 331148-B21.

For each document, insert the following sheets as shown here:

1. After page 30 in the HP StorageWorks SAN Switch 2/32 Installation Guide

2. After page 29 in the HP StorageWorks SAN Switch 2/16 Installation Guide

3. After page 32 in the HP StorageWorks SAN Switch 2/8 Installation Guide

Installing the Switch in a Rack Using the SAN Switch Universal Rack Mount Kit

Addendum Pg

HP StorageWorks SAN Switch 2/8|16|32 Installation Guide

Installing the Switch in a Rack Using the SAN Switch Universal

Rack Mount Kit

This section provides instructions for installing the SAN Switch 2/32, SAN

Switch 2/16, or SAN Switch 2/8 in an HP System/e rack, or in an HP 9000 Series

or comparable EIA rack using the SAN Switch Universal Rack Mount Kit, part

number 331148-B21.

Figure 1: SAN Switch 2/16 rack-mounted switch

Note: The Universal Rack Mount Kit installation requires two technicians.

The following items are required to install the switch in a rack:

■SAN Switch 2/32, SAN Switch 2/16, or SAN Switch 2/8

■Power cables

■#2 Phillips screwdriver

■7/16-inch wrench or socket

■The SAN Switch Universal Rack Mount Kit rails and rail mounting hardware

listed below:

(2) Rear mounting brackets

Installing the Switch in a Rack Using the SAN Switch Universal Rack Mount Kit

Addendum Pg

HP StorageWorks SAN Switch 2/8|16|32 Installation Guide

A right inner rail and a right outer rail

A left inner rail and a left outer rail

(14) #8-32 x 3/16-inch Phillips pan-head screw with captive

star lock washer

(10) #10-32 x 1/2-inch Phillips pan-head screw with captive

star lock washer

(8) #10 alignment washer

(8) #10 adapter washer

(2) 1/4-20 hex nut with captive star lock washer

(2) 1/4-inch flat washer

Installing the Switch in a Rack Using the SAN Switch Universal Rack Mount Kit

Addendum Pg

HP StorageWorks SAN Switch 2/8|16|32 Installation Guide

Caution: For proper airflow, the SFP media side of the SAN Switch 2/32,

SAN Switch 2/16, or SAN Switch 2/8 must face the rear of the rack. This

mounting allows air to enter from the front of the rack and to exhaust at the

rear of the rack, similar to other rack-mounted equipment. This prevents switch

overheating, which may cause it to fail.

To install the switch in a rack:

1. Check contents of the shipping carton to verify all the required parts and

hardware are available.

2. Choose a mounting location in the rack for the switch.

3. Attach the rear mounting brackets to the rear rack uprights by completing one

of the following steps:

— For an HP 9000 Series or comparable EIA rack, assemble each of the two

brackets with (2) #10-32 x 1/2-inch Phillips pan-head screws with captive

star lock washers and (2) #10 adapter washers as shown in Figure 2.

Figure 2: Installing the rear mounting brackets (HP 9000 Series or comparable EIA

rack)

Installing the Switch in a Rack Using the SAN Switch Universal Rack Mount Kit

Addendum Pg

HP StorageWorks SAN Switch 2/8|16|32 Installation Guide

— For an HP System/e rack, install each of the two rear mounting brackets

with (2) #10-32 x 1/2-inch Phillips pan-head screws and (2) #10

alignment washers as shown in Figure 3.

Figure 3: Installing the rear mounting brackets (HP System/e rack-left rear upright)

Installing the Switch in a Rack Using the SAN Switch Universal Rack Mount Kit

Addendum Pg

HP StorageWorks SAN Switch 2/8|16|32 Installation Guide

Note: This kit contains both left rails and right rails. The rails are marked with

Right

and

Left

to distinguish the rails from each other.

4. Assemble the outer rails by completing the following steps:

a. Attach the left outer rail and the right outer rails to the rear mounting

brackets using (2) 1/4-20 hex nuts with captive star lock washers attached

loosely as shown in Figure 4. Don’t tighten them. The nuts will be

tightened later in step 8.

Figure 4: Installing the outer rails (HP 9000 Series or comparable EIA rack)

Installing the Switch in a Rack Using the SAN Switch Universal Rack Mount Kit

Addendum Pg

HP StorageWorks SAN Switch 2/8|16|32 Installation Guide

b. Depending on the rack you are using, complete one of the following tasks:

— For an HP 9000 Series or comparable EIA rack, install two #10-32 x

1/2-inch Phillips pan-head screws with captive star lock washers and two

#10 adapter washers in the upper and lower hole locations of the right rail.

Then install two #10-32 x 1/2-inch Phillips pan-head screws with captive

star lock washers and two #10 adapter washers in the upper and lower

hole locations of the left rail. See Figure 5.

Figure 5: Assembling the outer rails (HP 9000 Series or comparable EIA rack)

Installing the Switch in a Rack Using the SAN Switch Universal Rack Mount Kit

Addendum Pg

HP StorageWorks SAN Switch 2/8|16|32 Installation Guide

— For an HP System/e rack, install two #10-32 x 1/2-inch Phillips pan-head

screws with captive star lock washers and two #10 alignment washers in

the upper and lower hole locations of the right rail. Then install two

#10-32 x 1/2-inch Phillips pan-head screws with captive star lock washers

and two #10 alignment washers in the upper and lower hole locations of

the left rail. See Figure 6.

Figure 6: Assembling the outer rails (HP System/e rack)

5. Determine the number of #8-32 x 3/16-inch Phillips pan-head screws with

captive star lock washers required to assemble the inner rails by referring to

Table 1.

Table 1: Number of screws required to assemble the inner rails

Switch

Number of #8-32 x 3/16-inch

Screws

SAN Switch 2/32 12

SAN Switch 2/16 10

SAN Switch 2/8 14

Installing the Switch in a Rack Using the SAN Switch Universal Rack Mount Kit

Addendum Pg

HP StorageWorks SAN Switch 2/8|16|32 Installation Guide

6. For the SAN Switch 2/32 and SAN Switch 2/16, perform step a. For the SAN

Switch 2/8, perform step b.

Caution: Do not use any other screws other than the fourteen that are

provided. Use of any longer lengths can cause damage to internal components

Note: The inner rails work for all three SAN switches—SAN Switch 2/32, SAN Switch

2/16, and SAN Switch 2/8. The mounting holes in the inner rails are marked with 32,

16, and 8. Use the appropriately labeled mounting holes when installing the inner rails

on a switch. For example, to install the inner rails on the SAN Switch 2/32, use the

mounting holes labeled with 32.

When viewing a rack from the front, the left rails are used in the left side of the rack and

the right rails are used in the right side of the rack. The rails must match up—right inner

with right outer and left inner with left outer. Note that the SAN switch mounts in the

rack with its front, the port side, facing the back of the rack. The rear of the switch, the

AC side, faces the front of the rack.

Other manuals for StorageWorks 2/16 - SAN Switch

This manual suits for next models

Table of contents

Other HP Switch manuals

HP J3128A AdvanceStack 10Base-T Hub-8E Installation and operating manual

HP JH321A Assembly instructions

HP 10504 User manual

HP Altoline 6921 User manual

HP 5920 Installation manual

HP A5120 EI Series User manual

HP B-Series User instructions

HP E8206 zl User manual

HP FlexFabric 5940 User manual

HP A7340A - Surestore FC 1Gb/2Gb Switch 16B User manual

HP A7533A - Brocade 4Gb SAN Switch Base Service manual

HP J3128A AdvanceStack 10Base-T Hub-8E User manual

HP PROCURVE 2610-PWR Series User manual

HP ProCurve 1810G User manual

HP Compaq Presario,Presario 1910 User manual

HP JC106A User manual

HP 6125G User manual

HP A7340A - Surestore FC 1Gb/2Gb Switch 16B Instruction Manual

HP Aruba Instant On 1830 Installation instructions

HP 527 User manual

HP ProCurve 8212zl Series User manual

HP JG221A User manual

HP PROCURVE 2910AL User manual

HP Procurve Series 4100GL User manual

Popular Switch manuals by other brands

URC

URC Total Control MFS-8 installation manual

Azbil

Azbil HPQ-D11 user manual

Sony

Sony DFS-900M operating instructions

SICK

SICK i17S operating instructions

F&F

F&F SZR-277 quick start guide

Shure

Shure UAMS/BK user guide

Dräger

Dräger X-zone Switch Off Instructions for use

Asco

Asco Joucomatic 349 Series manual

BT Mini Hub user guide

D-Link

D-Link DES-1226G manual

Johnson Controls

Johnson Controls FS80-C installation instructions

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Configuration guide

MicroNet

MicroNet SP1200A user manual

Ruijie

Ruijie RG-PF2920 Series Hardware installation and reference guide

Altinex

Altinex DA1914SX user guide

MiLAN

MiLAN MIL-SM2401M user guide

RJM

RJM MASTERMIND PBC/6X user manual

Atlas

Atlas MMK-KVM8 owner's manual