HP 20/700 User manual

62114 1

HP Surestore Tape Library 20/700 and

10/180 A5599A DLT Tape Drive

Installation Instruction

(for HP field service use only)

NOTE: If you are intermixing DLT7000 and DLT8000 tape drives in your

library, ensure that your backup application is configured

appropriately. The DLT7000 drive is not forward read-capable and

may overwrite a tape written by a DLT8000 drive.

CAUTION: HP tape library drives are not customer installable or replaceable.

Any servicing, adjustment, maintenance or repair must be performed only by

authorized HP service-trained personnel.

Note to Customer Engineer: This installation may add new technology to

the library that older user’s guides do not address. Please remind the

customer that the latest user documentation is available from the HP

Customer Care website: http://www.hp.com/go/support.

■Materials Included

Table 1. Materials List

Part Quantity

I/I DLT8000 1

DLT8000 Quick Reference Guide 1

DLT8000 Tape System Product Manual 1

DLT8000 Differential Drive Assembly 1

SCSI Y Cable 1

SCSI Differential Terminator 1

SCSI Mounting Screws 4

Power Termination Jumper 5

SCSI ID Jumper 10

HP Product ID Label 1

62114 2

■Installation Notes

• Confirm with the customer System Administrator that the tape library can be powered

off.

• Observe proper power off and power on procedures, as described in the Installation

or Service Manuals.

• HP has the drive factory set the drive to differential operation.

• When you install a DLT8000 tape drive remove the Product ID Label, located on the

drive, and place it in the appropriate box on the Drive Location Label. The Drive

Location Label is located on the inside of the library door, just below the UL label.

62114 3

■Tape Library Attachment

Perform these procedures to install a DLT8000 drive in an 20/700 library:

Tools Required

•Phillips screwdriver

•3/16-inch nut driver

❑Remove shipping restraint

❑Install drive(s) in library

❑Attach Y-cable between the drive and library bulkhead

❑Attach interface cable to drive

❑Power-on drive

❑Configure DLT drive

❑Attach SCSI Terminator

❑Attach interface cable to host

62114 4

■Library Drive Attachment

Tape drives are shipped individually. Due to the size differences of the DLT and 9840

drives, there are a variety of ways of installing the drives. Typically, drive installation moves

from the bottom slot and up.

Refer to Figure 1 and the explanation below for the configuration rules for installing drives.

1. The first callout in Figure 1 shows that the uppermost drive slot in the drive column can only be a

DLT drive.

2. The second callout depicts the size ratio of the 9840 drives to the DLT drives. In size, two

9840 drives fit in the same space as three DLT drives.

3. The third callout shows this ratio again: three DLT drives fit in the same space as two 9840

drives.

4. The fourth callout depicts a mixture of 9840 and DLT drives.

You may also install six 9840 drives plus one DLT drive in a column, where the DLT

drive occupies the top drive slot.

The following table lists the available combinations for one drive column.

9840 DLT

010

62114 5

Figure 1. Tape Drive Installation Guidelines

Tape Drive Installation Guidelines (H_53393)

1. DLT drive only in this position

2. Two 9840 drives (shown) or three DLT drives

3. Three DLT drives (shown) or two 9840 drives

4. Mixed 9840 and DLT drives (shown), three DLT drives, or two 9840 drives

NOTE:This graphic depicts the size relationship between DLT and 9840 drives ONLY.

Installation instructions call for installing the 9840 drives in the bottom slots, and the

DLT drives in the upper slots.

62114 6

■Installing DLT Drives

For DLT drives, follow the procedure below to unpack and install the drives.

DLT tape drives are shipped with the following, non-selectable configurations:

•DLT8000 (manufacturer’s model number)

•Differential operation

Refer to Figure 2 and make sure that the labels on the drive match the drive type and

operation required.

NOTE:Check with the customer for their maintenance agreement on tape drives. If

the customer agreement is to return the drives for repair, have them retain

one shipping box, with packing material, to be sent back to the factory.

Figure 2. DLT Labels

DLT Labels (H_65115)

1. Manufacturer’s model number label

2. Differential label (and drive serial number)

62114 7

NOTE:Refer to Figure 3 for the following procedure.

CAUTION: DLT equipment damage: Do not move the load latch of a tape drive by

hand until told to do so in later instructions.

1. Open the drive access section of the library (at the right side, as viewed from the front of

the library) by lifting up on the two latches. Turn the latches counterclockwise and open

the side door.

2. Open the drive package.

3. Remove the packing material.

4. Refer to Figure 3 while checking the side of the DLT drive for the terminating power

jumper selection.

CAUTION: Loss of data or degradation of performance: HP recommends

supplying terminating power (TERMPWR) from devices attached at both ends of

the SCSI bus. Industry standards advise that no more than three devices provide

terminating power to the bus.

Verify whether TERMPWR for DLT drives is on or off (enabled or disabled) for each

tape drive. If needed, move the jumper to match your requirement.

•TERMPWR On: Install the jumper on the pins shown in the following figure.

•TERMPWR Off: Remove the jumper on the pins shown in the following figure.

You can store the strap by placing it on one pin only.

NOTE:You may need to remove the DLT drive from its library tray to gain

access to this jumper. If removal is required, carefully turn the drive

upside down and remove drive mounting screws. Change the jumper

as required. Replace the drive mounting screws.

5. Carefully place each drive near the rear slots at the right side of the library.

62114 8

6. Look inside the drive column area and determine the slot you wish to use for each drive.

Following the lifting procedures described in Chapter 2 “Safety and ESD”, of the Instal-

lation Manual firmly grasp the drive at the rear with one hand and place the other hand

under the drive mounting plate.

7. Carefully guide the drive into its slot. Push it in as far as it will go and firmly seat the

drive.

NOTE:In the following step, do not over tighten the thumbscrew.

8. Refer to Figure 4 and turn the thumbscrew clockwise until it is secure.

Figure 3. Terminating Power Jumper DLT Drive

Terminating Power Jumper—DLT Drive (H_65116)

1. DLT drive

2. Load latch

3. TERMPWR jumper (enabled)

62114 9

Figure 4. Tape Drives Rear View

Tape Drives—Rear View (H_65124)

1. DLT power switch

2. Thumbscrews

3. 9840 power switch

62114 10

■Installing DLT Cable Connectors

The following procedures describe how to install the tape channel connectors for the tape

drives.

Standard Drive Column 0 Connectors.

NOTE:Drive column 0 is the standard drive column included in all libraries. It is

the column that contains the calibration label at the bottom. Also, some

of the following steps may require two people.

1. Go to the rear of the library, open the door, and locate the connector bulkhead.

2. Remove the SCSI “Y”channel cable and mounting screws from the drive box.

3. Refer to Figure 5 and insert the two channel connectors into the slots on the interior library

bulkhead, next to the desired drive location.

4. From the rear bulkhead, thread the four mounting screws into the connectors.

5. Tighten the mounting screws with a 3/16-inch nutdriver.

6. Insert the single connector end into the DLT drive.

7. Repeat these steps for all drives in column 0.

8. When you are finished installing all drives, place the drive power switch(es) to the ON (|)

position.

9. Close the rear door.

Figure 5. Tape Drive Cable Connectors

Tape Drive Cable Connectors (H_65226)

1. Interior bulkhead view

2. Exterior bulkhead view

Other manuals for 20/700

This manual suits for next models

Table of contents

Other HP Storage manuals

HP DW017B - StorageWorks Ultrium 448 Tape Drive Instruction Manual

HP StoreVirtual 4630 Operating manual

HP STORAGEWORKS XP24000 User manual

HP MSA 2040 User instructions

HP MSA 2050 User manual

HP 3PAR StoreServ 7000 Technical manual

HP 9840 User manual

HP P9000 User manual

HP 5243-2SE User manual

HP Surestore FC10 - Disk Array User manual

HP StorageWorks 4000/6000/8000 - Enterprise Virtual... Instruction Manual

HP Colorado Trakker 250 Instruction Manual

HP Converged Architecture 700 Quick reference guide

HP StorageWorks 2012i User manual

HP StorageWorks MSL6000 series User manual

HP StorageWorks 6000 - Virtual Library System User manual

HP StorageWorks 8B - FC Entry Switch User manual

HP Surestore 6164 - Switch User manual

HP Surestore Disk Array 12h - And FC60 Assembly instructions

HP EVA P6000 User manual

HP StorageWorks XP48 - Disk Array User manual

HP Storevirtual 4000 Quick reference guide

HP 3PAR StoreServ 7200 2-node User manual

Popular Storage manuals by other brands

QNAP

QNAP TS 32PXU Series user guide

LaCie

LaCie RUGGED RAID user manual

Freecom

Freecom CLS DOCK Quick install guide

PNY

PNY Attache P-FD64MBATT3 install guide

OLT

OLT 6x6 Maximizer Assembly manual

Transcend

Transcend JetFlash 160 Specifications

LaCie

LaCie RUGGED MINI user manual

Thunderbolt

Thunderbolt 600 user manual

Panasonic

Panasonic LB-DH8 series Operator's guide

Intel

Intel RAID High Availability user guide

LaCie

LaCie 12big Thunderbolt 3 Quick install guide

Spectra Logic

Spectra Logic T-Series Spectra T50e quick start guide

Panasonic

Panasonic LKM-F931-1 instruction manual

Tabernus

Tabernus Enterprise Erase E2400 user guide

Rocstor

Rocstor COMMANDER 3F series user manual

Western Digital

Western Digital Ultrastar Data60 installation guide

Dell

Dell PowerVault MD3600f Series Getting started

CFI

CFI TERA STOR SATA RAID IV user manual