HP 20/700 Quick start guide

62108 1

HP Surestore Tape Library 20/700

A5605A Expansion Frame Installation Guide

(for HP field service use only)

CAUTION: The HP tape library Expansion Frame is not customer installable or

replaceable. Any servicing, adjustment, maintenance or repair must be performed only

by authorized HP service-trained personnel.

Note to Customer Engineer: This installation may add new technology to the library

that older user’s guides do not address. Please remind the customer that the latest user

documentation is available from the HP Customer Care website: http://www.hp.com/go/

support.

■Materials Included

■Installation Notes

• Confirm with the customer System Administrator that the tape library can be powered

off.

• Observe proper power down and power on procedures, as described in the

Installation or Service Manual.

• If you install or replace an Expansion Module you must check mark the appropriate

box on the Drive Location Label. The Drive Location Label is located on the inside of

the library door, just below the UL label.

•Heavy Load. At least three people are required to remove the Expansion Frame from

packaging and push it into position.

Tools Required

Prior to beginning the installation process, obtain the following tools:

• 1/4-inch Ratchet Wrench

Table 1. Materials List

Part Quantity

I/I Expansion Frame 1

Expansion Frame Assembly 1

1/4-20 x 1/2-in. Torx Screws 6

Lock Down Latch Tool 1

62108 2

■Expansion Frame Install

1. Have the operator take the library and all drives offline and power off the tape library.

2. Obtain key and open cartridge area door.

CAUTION: Lifting hazard. Two people are required to remove the rear cover.

3. Remove the right rear cover (cover with window) by inserting the lock-down latch tool

(see “Special Tools”) between rear cover and the tape library frame on the lower right-hand

side of cover to release cover lock-down latch (see Figure 1).

Figure 1. Removing Right Rear Cover

62108 3

4. Slide cover up and set aside.

5. Using a T30 Torx driver, remove the mushrooms from the tape library frame (6 places) in

the area where the cover was removed (see Figure 1).

6. Position the robotic hand at the top of the Z-column and point it toward the drives.

CAUTION: Be careful not to hit your head on the theta lock down bracket

mounted to the top inside surface of the tape library frame.

7. Using a T15 Torx driver, remove the twelve No. 6-32 x 3/8-in. Torx Pan Head screws

holding the front left plate to the drive tower (see Figure 2). Set the screws and plate aside.

8. If required, remove any customer data cartridges from the cells in Panel 2, Column 3 and

4. Be careful not to damage the cartridges.

Note: The array labels appear directly above the arrays.

9. Remove the array retainer clip and the arrays from Panel 2, Column 3 and 4.

10. Reposition the robotic hand to point to Panel 2, Column 4 (where arrays were removed in

Step 7).

11. Remove theta stop closest to the drives using a flat blade screwdriver (see Figure 2).

Removing Right Rear Cover (a5605a_01)

1. Rear Cover

2. Mushroom (6x)

3. Lock-Down Latch Tool

4. Lock-Down Latch

5. Mushroom (Ref)

6. Mushroom (Ref)

Figure 1. Removing Right Rear Cover (Continued)

62108 4

Figure 2. Theta Stop and Mounting Holes

Theta Stop and Mounting Holes (a5605a_02)

1. Mounting Hole Locations

2. Remove Theta Stop

3. Mounting Hole Locations

4. Measure the distance from the floor to the inside floor of library

5. Front Left Plate

62108 5

CAUTION: Heavy Load. At least three people are required to remove the Expansion

Frame from packaging and push it into position.

12. Remove the expansion frame from its package and place it flat on the floor.

13. Measure the distance from the floor of the room to the inside floor of the tape library (see

Figure 2).

14. Adjust the leveling bolts (4 places) on the expansion frame (measured from the inside

floor of expansion frame to the bottom of the leveling bolt) to be 1/16-inch to 1/8-inch

shorter than what was measured in Step 13.

15. Stand the expansion frame up on the leveling bolts and position it against the frame of the

tape library. Be careful not to bend the leveling bolts when moving the expansion frame

into position.

16. To correctly align the expansion frame with the tape library:

•Align bottom locating pin in expansion frame to the hole in the tape library

floor.

•Align the top locating pin in the expansion frame to the top slot in the tape

library.

•Push the expansion frame firmly against the tape library frame (see Figure 3).

17. While holding the expansion frame in position, adjust the two leveling bolts closest to the

back until they touch the floor (see Figure 3).

62108 6

CAUTION: Be careful not to hit your head on the theta lock down bracket mounted to the

top inside surface of the tape library frame.

18. From the inside of the cartridge area, install six 1/4-20 x 1/2-in. long screws, using a T30

Torx driver, through the holes in the tape library frame into the expansion frame (see

Figure 2 for screw locations) and tighten.

19. Using a T15 Torx driver, reinstall the plate to the left side of the drive using the 12 No.6-

32 screws previously removed in Step 7.

Figure 3. Expansion Frame Alignment

Expansion Frame Alignment (a5605a_03)

1. Top Locating Pin

2. 1/4-20 x 1/2-in. Torx Screw (6x)

3. Expansion Frame

4. Leveling Bolt (4x)

5. Bottom Locating Pin

62108 7

20. Replace the arrays, the array retainer clips, and cartridges removed in Step 7 back to Panel

2, Column 3 and 4.

21. Close the tape library doors and lock.

22. Power the tape library on and verify that it initializes and audits properly.

23. Return unit to customer.

62108

REV C

EC 111700A

Hewlett-Packard Company/

Storage Technology Corp

Edition 1/2002

Other manuals for 20/700

This manual suits for next models

Table of contents

Other HP Storage manuals

HP LTO-4 HH User manual

HP Surestore 6164 - Switch User manual

HP StorageWorks 4000/6000/8000 - Enterprise Virtual... Instruction Manual

HP Alletra 4120 Assembly instructions

HP ProLiant DL100 G2 DPSS User manual

HP StorageWorks 3000 - RAID Array Quick guide

HP StorageWorks ESL E-Series User manual

HP LTO Ultrium Product manual

HP AJ765A - StorageWorks RDX Removable Disk Backup... Instruction Manual

HP XP7 User manual

HP StorageWorks DLT80 User manual

HP StorageWorks DAT320 USB Instruction Manual

HP StorageWorks 4000/6000/8000 - Enterprise Virtual... Instruction Manual

HP P9000 User manual

HP Designjet 220 User instructions

HP 9840 User manual

HP Dv4 1140go - Pavilion Entertainment - Core 2 Duo... User manual

HP DW017B - StorageWorks Ultrium 448 Tape Drive Instruction Manual

HP StoreEver MSL2024 Troubleshooting guide

HP 6400/8400 Guide

HP 3000 - 37XE System Instruction Manual

HP D2D User manual

HP 3PAR StoreServ 7200 2-node User manual

HP 3PAR StoreServ 7000 User manual

Popular Storage manuals by other brands

QNAP

QNAP TS 32PXU Series user guide

LaCie

LaCie RUGGED RAID user manual

Freecom

Freecom CLS DOCK Quick install guide

PNY

PNY Attache P-FD64MBATT3 install guide

OLT

OLT 6x6 Maximizer Assembly manual

Transcend

Transcend JetFlash 160 Specifications

LaCie

LaCie RUGGED MINI user manual

Thunderbolt

Thunderbolt 600 user manual

Panasonic

Panasonic LB-DH8 series Operator's guide

Intel

Intel RAID High Availability user guide

LaCie

LaCie 12big Thunderbolt 3 Quick install guide

Spectra Logic

Spectra Logic T-Series Spectra T50e quick start guide

Panasonic

Panasonic LKM-F931-1 instruction manual

Tabernus

Tabernus Enterprise Erase E2400 user guide

Rocstor

Rocstor COMMANDER 3F series user manual

Western Digital

Western Digital Ultrastar Data60 installation guide

Dell

Dell PowerVault MD3600f Series Getting started

CFI

CFI TERA STOR SATA RAID IV user manual