HP Vectra VL800 User manual

Smart MK3

Installation Guide

Notice

The information contained in this document is subject to change without notice.

Hewlett-Packard makes no warranty of any kind with regard to this

material, including, but not limited to, the implied warranties of

merchantability and fitness for a particular purpose.

Hewlett-Packard shall not be liable for errors contained herein or for incidental

or consequential damages in connection with the furnishing, performance, or use

of this material.

Hewlett-Packard assumes no responsibility for the use or reliability of its

software on equipment that is not furnished by Hewlett-Packard.

This document contains proprietary information that is protected by copyright.

All rights are reserved. No part of this document may be photocopied,

reproduced, or translated to another language without the prior written consent

of Hewlett-Packard Company.

Microsoft®, Windows® and MS-DOS® are registered trademarks of Microsoft

Corporation.

MMX TM is a trademark of Intel Corporation.

Pentium® is a registered trademark of Intel Corporation.

Hewlett-Packard France

Business Desktop Division

38053 Grenoble Cedex 9

France

Read This First

Before installing the network adapter:

If your OS is Windows NT 4.0, go into the BIOS setup and set PnP OS field to NO.

If your OS is Windows 98 2nd edition, go into the BIOS setup and set PnP OS field to

YES.

If your OS is Windows 2000 Professional, go into the BIOS setup and set PnP OS

field to YES.

If your OS is Windows NT4.0 and Wake on LAN capability is needed, go into the

BIOS setup and enable power-up when a specific command is received by the

Network Interface.

For all OS, remove any previously installed network adapter (usually located in slot

#5) if it is not needed.

Installing the network adapter in slot #4 is recommended. HP has tested this

installation procedure using slot #4.

For advanced users only: In case of resource conflict, you can try to change the

resources for the network adapter. To do this, turn the Vectra system power off,

remove the network adapter and install it into a different PCI slot.

Connecting to a Novell NetWare 5.1 or 4.11 Server

Microsoft Windows NT 4.0 Workstation

Requirements

Operating System Windows NT 4.0 Workstation

Driver Version 6.04

Driver File MDGNDIS4.SYS

Server OS NetWare 5.1 or 4.11 Server

Client OS Client v4.80 for Windows NT/2000

Procedure

1. With the HP Vectra turned off, install the network adapter into an available PCI

slot.

2. Connect the network cable to the newly installed network adapter.

3. Connect the WOL cable between the network adapter and the PC motherboard.

4. Power on the machine and boot to Windows.

5. Logon to Windows with administrator privileges.

6. Click OK to ignore the warning message indicating a driver failed during system

startup. This is caused the removal of the previously installed network adapter.

This message should no longer appear after removing the driver from the

Network properties.

7. The following steps are based on a subsequent installation of Networking on the

system. Adding a network adapter for the first time has some minor differences.

Ask your administrator for more information.

8. Open the Network properties windows to remove a previously installed network

adapter and to add a new one.

9. Click on the “Adapters”tab and highlight the network adapter you want removed

then click on the “Remove”button.

10. Click on the “Adapters”tab then on the “Add”button.

11. Insert the driver disk and click on “Have Disk”.

12. Type in the location of the NDIS4 drivers and click on “OK”.

13. With “Madge Automated Installation - RECOMMENDED”highlighted, click on

“OK”.

14. Select “Madge Smart 16/4 PCI Ringnode Mk3”and click on “Properties”. Click on

the “Advanced”button and enable Wake-On-LAN.

15. Additional changes in the Network properties, such as: workgroup name,

computer name, TCP/IP properties, etc. may be necessary. Ask your Network

Administrator for more information.

16. Click on “Close”to complete the installation.

17. Remove the driver disk and click on “Yes”when prompted to restart your

computer.

18. Logon to Windows with administrator privileges.

19. From the location of the “Novell Client v4.80 for Windows NT/2000”installation

files, execute “SETUPNW.EXE”.

20. Select either “Typical”or “Custom”and click on “Install”. Typical Installation is

normally chosen. Select Custom Installation only if you are an administrator or an

advanced user. When prompted for options during installation, ask your Network

Administrator for more information.

21. Click on “Yes”to accept the “Novell Terms and Conditions”.

22. Click on “Reboot”to restart the system once the installation is complete.

23. Logon to Windows with administrator privileges and re-install the current service

pack.

Connecting to a Microsoft Windows 2000 Advanced or NT 4.0

Server

Microsoft Windows NT 4.0 Workstation

Requirements

Operating System Windows NT 4.0 Workstation

Driver Version 6.04

Driver File MDGNDIS4.SYS

Server OS Windows 2000 Advanced or NT 4.0

Server

Client OS Microsoft

Procedure

1. With the HP Vectra turned off, install the network adapter into an available PCI

slot.

2. Connect the network cable to the newly installed network adapter.

3. Connect the WOL cable between the network adapter and the PC motherboard.

4. Power on the machine and boot to Windows.

5. Logon to Windows with administrator privileges.

6. Click OK to ignore the warning message indicating a driver failed during system

startup. This is caused the removal of the previously installed network adapter.

This message should no longer appear after removing the driver from the

Network properties.

7. The following steps are based on a subsequent installation of Networking on the

system. Adding a network adapter for the first time has some minor differences.

Ask your administrator for more information.

8. Open the Network properties windows to remove a previously installed network

adapter and to add a new one.

9. Click on the “Adapters”tab and highlight the network adapter you want removed

then click on the “Remove”button.

10. Click on the “Add”button to add the new network adapter.

11. Insert the driver disk and click on “Have Disk”.

12. Type in the location of the NDIS4 drivers and click on “OK”.

13. With “Madge Automated Installation - RECOMMENDED”highlighted, click on

“OK”.

14. Select “Madge Smart 16/4 PCI Ringnode Mk3”and click on “Properties”. Click on

the “Advanced”button and enable Wake-On-LAN.

15. Additional changes in the Network properties, such as: workgroup name,

computer name, TCP/IP properties, etc. may be necessary. Ask your Network

Administrator for more information.

16. Click on “Close”to complete the installation.

17. Remove the driver disk and click on “Yes”when prompted to restart your

computer.

18. Logon to Windows with administrator privileges and re-install the current service

pack.

Connecting to a Novell NetWare 5.1 or 4.11 Server

Microsoft Windows 98 2nd edition

Requirements

Operating System Windows 98 2nd edition

Driver Version 6.04

Driver File MDGNDIS4.SYS

Server OS NetWare 5.1 or 4.11 Server

Client OS Client v3.30 for Windows 95/98

Procedure

1. With the HP Vectra turned off, install the network adapter into an available PCI

slot.

2. Connect the network cable to the newly installed network adapter.

3. Connect the WOL cable between the network adapter and the PC motherboard.

4. Power on the machine and boot to Windows.

5. Windows will detect the network adapter as “PCI Token Ring Controller”.

6. Insert the driver disk and click on “Next”to continue the installation.

7. Accept the default selection: “Search for the best driver for your device

(Recommended).”and click “Next”.

8. Select the locations Windows will search for drivers. Check “Specify a location:”

and type in or browse the location of the NDIS4 driver. Click “Next”to continue.

9. Accept the driver found, “Madge Smart 16/4 PCI Ringnode Mk3”, by clicking on

“Next”.

10. Click on “Finish”when the driver installation is complete.

11. Remove the driver disk and click on “Yes”when prompted to restart the system.

12. Additional changes in the Network properties, such as: workgroup name,

computer name, TCP/IP properties, etc. may be necessary. Ask your Network

Administrator for more information. After changes are made, a restart will be

necessary.

13. From the location of the “Novell Client v3.30 for Windows 95/98”installation files,

execute “Setup.exe”.

14. Click on “Yes”to accept the “Novell Terms and Conditions”.

15. Select either “Typical”or “Custom”and click on “Install”. Typical Installation is

normally chosen. Select Custom Installation only if you are an administrator or an

advanced user. When prompted for options during installation, ask your Network

Administrator for more information.

16. Click on “Reboot”once the Novell client installation is complete.

Known Problems

Problem1

There is an issue with waking up the system. Currently there is no resolution to the

problem. However, the problem can be prevented by not placing the system on

Stand by. Also, the Power Management properties’"Turn off monitor:" and “System

standby:”settings must be set to “Never”.

Connecting to a Microsoft Windows 2000 Advanced or NT 4.0

Server

Microsoft Windows 98 2nd edition

Requirements

Operating System Windows 98 2nd edition

Driver Version 6.04

Driver File MDGNDIS4.SYS

Server OS Windows 2000 Advanced or NT 4.0

Server

Client OS Microsoft

Procedure

1. With the HP Vectra turned off, install the network adapter into an available PCI

slot.

2. Connect the network cable to the newly installed network adapter.

3. Connect the WOL cable between the network adapter and the PC motherboard.

4. Power on the machine and boot to Windows.

5. Windows will detect the network adapter as “PCI Token Ring Controller”.

6. Insert the driver disk and click on “Next”to continue the installation.

7. Accept the default selection: “Search for the best driver for your device

(Recommended).”and click “Next”.

8. Select the locations Windows will search for drivers. Check “Specify a location:”

and type in or browse the location of the NDIS4 driver. Click “Next”to continue.

9. Accept the driver found, “Madge Smart 16/4 PCI Ringnode Mk3”, by clicking on

“Next”.

10. Click on “Finish”when the driver installation is complete.

11. Remove the driver disk and click on “Yes”when prompted to restart the system.

12. Additional changes in the Network properties, such as: workgroup name,

computer name, TCP/IP properties, etc. may be necessary. Ask your Network

Administrator for more information. After changes are made, a restart will be

necessary.

Other manuals for Vectra VL800

This manual suits for next models

Table of contents

Other HP Software manuals

HP C7791C - DesignJet 130 Color Inkjet Printer Configuration guide

HP Integrity rx1620 User manual

HP StorageWorks All-in-One SB600c - Storage... User manual

HP Integrity BL860c Quick reference guide

HP Xw460c - ProLiant - Blade Workstation User manual

HP Media Center m1000 - Desktop PC Quick start guide

HP P9000 Instruction Manual

HP NAS 1200s Instruction Manual

HP 4320t - Mobile Thin Client Mounting instructions

HP D6030A - NetServer - E50 User manual

HP C7791C - DesignJet 130 Color Inkjet Printer Configuration guide

HP LeftHand P4000 - SAN Solutions Instruction Manual

HP 742n - Pavilion - 512 MB RAM Installation and operating instructions

HP C7791C - DesignJet 130 Color Inkjet Printer Configuration guide

HP OmniBook 2100 User manual

HP ProLiant BL280c G6 User manual

HP Brocade 8/24c Instruction Manual

HP Integrity rx1600 Quick reference guide

HP SysMan User manual

HP 1032 User manual

HP C7791C - DesignJet 130 Color Inkjet Printer Configuration guide

HP J3111A - JetDirect 600N Network Card Instruction Manual

HP AK373A - StorageWorks All-in-One Storage System 1200r 5.4TB SAS Model NAS... How to use

HP T5145 - Thin Client - Tower Service manual

Popular Software manuals by other brands

COMPRO

COMPRO COMPROFM manual

Muratec

Muratec OFFICEBRIDGE ONLINE user guide

Oracle

Oracle Contact Center Anywhere 8.1 installation guide

Adobe

Adobe 65007312 - Photoshop Lightroom Programmer's guide

Avaya

Avaya NULL One-X for RIM Blackberry user guide

PS Audio

PS Audio PowerPlay Programming manual

Brady

Brady LOCKOUT PRO 3.0 Administrator's guide

Avaya

Avaya Interaction Center user guide

Texas Instruments

Texas Instruments TI-83 Plus Silver Edition Guide book

Novell

Novell GROUPWISE 8 - INTERNET AGENT manual

Oracle

Oracle Application 9i Configuration guide

Acer

Acer RDM user guide

Canon

Canon Vixia HF21 instruction manual

Canon

Canon ZR950 instruction manual

Samsung

Samsung Auto Backup user manual

Polycom

Polycom Vortex EF2201 Application note

Brocade Communications Systems

Brocade Communications Systems Brocade 8/12c user manual

Novell

Novell SP2 - S release note