HP ProCurve 1600M User manual

HP ProCurve Switch Quick Setup Guide

These images are examples only. Your switch may look a little different.

➊Unpack and check included parts:

•Switch

• Switch Quick Setup Guide

• Read Me First

• Safety and Regulatory booklet

• Customer Support/Warranty booklet

•Consolecable

• Accessory kit

• Power cord

➋Prepare for installation.

To avoid personal injury or product damage, review

the installation guidelines on the next page.

➌Verify selftest by connecting the power cord.

➍Install mounting brackets.

➎Mount the switch and connect the power cord.

➏(Optional) Connect console cable.

➐Configure (minimal configuration).

➑Connect network cables.

For more installation information refer to the Installation

and Getting Started Guide for your product, located on

the HP ProCurve Web site at:

www.procurve.com/manuals.

Note: Before installing the switch in a rack, check the

Installation and Getting Started Guide for specific rack

installation instructions.

Port LEDs

Test LED

Power and

Fault LEDs

Console

cable

To PC

By default, the switch is configured to acquire an IP address config-

uration from a DHCP or Bootp server.

For more information on configuration and remote management, see

the Management and Configuration Guide for your switch, which is

on the ProCurve Web site at www.procurve.com/manuals.

RJ-45

connector

Fiber cable

connector

Installation Guidelines

To avoid personal injury or product damage when installing your switch, read the installation precautions and

guidelines below.

For Safety and Regulatory information refer to the Safety and EMC Regulatory booklet included with the switch.

Installation Precautions

Warnings

■The rack or cabinet should be adequately secured to prevent it from becoming unstable and/or falling

over.

■Devices installed in a rack or cabinet should be mounted as low as possible, with the heaviest devices

at the bottom and progressively lighter devices installed above.

■Do not wall mount any switch without checking for restrictions in the Installation and Getting

Started Guide.

Cautions

■If the switch is to be shipped in a rack, be sure to use only an HP 10K rack. Mount the switch using rail kit part

number 356578-B21 and shelf kit AB469A. Both kits must be used. Otherwise you will void the switchwarranty.

■Ensure the power source circuits are properly grounded, then use the power cord supplied with the switch to

connect it to the power source.

■If your installation requires a different power cord than the one supplied with the switch and power supply, be

sure the cord is adequately sized for the switch’s current requirements. In addition, be sure to use a power cord

displaying the mark of the safety agency that defines the regulations for power cords in your country. The mark

is your assurance that the power cord can be used safely with the switch and power supply.

■When installing the switch, the AC outlet should be near the switch and should be easily accessible in case the

switch must be powered off.

■Ensure the switch does not overload the power circuits, wiring, and over-current protection. To determine the

possibility of overloading the supply circuits, add together the ampere ratings of all devices installed on the

same circuit as the switch and compare the total with the rating limit for the circuit. The maximum ampere

ratings are usually printed on the devices near the AC power connectors.

■Do not install the switch in an environment where the operating ambient temperature exceeds its specification.

■Ensure the air flow around the switch is not restricted. Leave at least 3 inches (7.6 cm) for cooling. For the air

flow direction, see the Installation and Getting Started Guide for your product, located on the HP ProCurve

Web site at www.procurve.com/manuals.

Part Number: 5992-4964

November 2008

Printed in Singapore

*5992-4964*

Development Company, L.P.

The information herein is subject to

change without notice.

Other manuals for ProCurve 1600M

Table of contents

Other HP Network Hardware manuals

HP SL500 (M852x) User manual

HP Wireless LAN 802.11b/g Device WN4201B User manual

HP Mv2120 - Media Vault Network Drive User manual

HP Presario X1000 - Notebook PC User manual

HP X1600 - StorageWorks Network Storage System 5.4TB SAS Model NAS... User manual

HP FF 12910 Assembly instructions

HP A3550A - High Availability Disk Arrays Model 20 Storage... User manual

HP AT084A Installation guide

HP ProCurve XL MINI-GBIC User manual

HP 5900AF-48XG-4QSFP+ Assembly instructions

HP X1600 - StorageWorks Network Storage System 5.4TB SAS Model NAS... How to use

HP JG602A User manual

HP FlexNetwork 6616 User manual

HP 400338-001 - KVM Switch User manual

HP E8491B IEEE 1394 User manual

HP 12500 Series User manual

HP Aruba EdgeConnect Extra-Small Chassis User manual

HP Bc1500 - BladeSystem - Blade PC Manual

HP AdvanceNet 30244M Manual

HP X5000 G2 Service manual

HP IBRIX X9720 Service manual

HP ProLiant DL980 G7 Quick reference guide

HP 85027A Service manual

HP A3550A - High Availability Disk Arrays Model 20 Storage... User manual

Popular Network Hardware manuals by other brands

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL product manual

B&B Electronics

B&B Electronics ZXT9-IO-222R2 product manual

Yudor

Yudor YDS-16 user manual

D-Link

D-Link ShareCenter DNS-320L datasheet

Samsung

Samsung ES1642dc Hardware user manual

Honeywell Home

Honeywell Home LTEM-PV Installation and setup guide

evertz

evertz 7700 Series manual

D-Link

D-Link ShareCenter DNS-343 Quick installation guide

Asante

Asante AsanteBridge 1012 user guide

FireBrick

FireBrick FB2700 user manual

Audiovox Electronics

Audiovox Electronics ARWH2T user manual

ADC

ADC DSX-1 Operational Procedures Guide

NetComm

NetComm NF2 user guide

Alcatel-Lucent

Alcatel-Lucent 5620 user guide

Dell EMC

Dell EMC XC6420 Series Solution guide

Lanner

Lanner NCA-1020A user manual

Allied Telesis

Allied Telesis AT-TN121-A Specifications

Arista

Arista CCA-ETM-Q12 quick start guide