Howard Miller 611319 Installation manual

FLOOR CLOCK SETUP

and OPERATING INSTRUCTIONS

CLOCK SETUP INSTRUCTIONS

1. Move the clock close to its nal location for assembly and setup. Make sure the clock is positioned rmly on the oor.

Levelers are provided on the bottom of the clock (Figure 1). Adjust levelers for maximum stability and proper alignment.

WARNING: ENSURE CLOCK IS POSITIONED SQUARE AND FIRM ON THE FLOOR SO THAT IT WILL NOT FALL OVER. KEEP

CHILDREN AWAY FROM THE CLOCK.

WARNING: KEEP PLASTIC BAGS AND SMALL PARTS AWAY FROM CHILDREN

Figure 1

Floor Leveler

Figure 2 Figure 3

2. Locate the Power Supply (Figure 2) and connect it to the Lamp Cord located at the back of the clock base (Figure 3).

3. Move the clock to the nal location and plug. See page 4 for Safety Strap installation instructions.

4. Plug the Power Supply into an electrical outlet. Turn the Lamp on by touching the Round Metal Touch Plate on the back of the clock base (gure 4).

There are four levels of lighting: low, medium, high, and off.

5. The direction of the light may be adjusted by pushing gently with your nger on the Lamp (gure 5).

Figure 4 Figure 5

Power

Supply

Lamp

Cord

Power

Supply

Cord

Round Metal

Touch Plate

Lamp

Appearance may vary.

Battery

Housing

Transport

Locking

Figure 8

Pendulum

Guide

10. Release the Pendulum Guide from the Transport-Locking Pin (Figure 8) by gently pushing it sideways, allowing the Pendulum Guide to hang freely.

11. Install two new “C” size alkaline batteries according to the +/- symbols in the Battery Housing. (Figure 8)

9. Locate the Pendulum Driver and Battery Housing inside the Head Assembly (Figure 7).

Figure 7

Head Assembly

Battery Housing

Pendulum Driver

6. Locate the clock’s quartz movement on the back of the dial.

7. Install one new “AA” size alkaline battery according to the +/- symbols in the battery holder (Figure 6).

8. Set the time by using the Time Setting Knob (Figure 6) to rotate the hands to the correct time.

Time Setting Knob

Figure 6

AA Alkaline Battery

12. Install the Head Assembly to the back of the dial by placing the at edge of the Head Assembly over the Metal Bracket and carefully pulling the Head

Assembly down until it rests completely level at the bottom of the Metal Bracket (Figures 9 & 10).

NOTE: Make sure the Head Assembly is secure before installing the Pendulum.

13. Hang the Pendulum by the Pendulum Hook on the Pendulum Guide. (Figure 11 & 12).

14. The Pendulum hook must t snug on the Pendulum Guide to prevent wobbling and erratic movement. If the Pendulum fails to continue swinging or

wobbles, the Pendulum Hook can be tightened to t snug to the Pendulum Guide by squeezing the Pendulum Hook with pliers as shown (Figure 12).

NOTE: Make sure the pendulum is secure before operating.

15. Start the Pendulum by moving it to the far left of center and release it to swing. The Pendulum should swing freely.

BATTERY REPLACEMENT

If the clock begins to lose time or the pendulum does not swing, this is a sign of weak or exhausted batteries. Replace with new alkaline batteries.

Head

Assembly

Metal

Bracket

Figure 9 Figure 10

Figure 12Figure 11

Pendulum Hook

Pendulum

Guide

Pendulum

SAFETY STRAP

A safety strap has been included with your clock. Due to the variety of oor coverings (i.e. plush carpets, linoleum, etc.), it is important that the clock be

positioned square and rm on the oor. Adjustable levelers have been assembled to the bottom of the clock for this purpose. To help ensure the clock

will not tip over, attach the wall Safety Strap.

MOUNTING OPTIONS:

The preferred option would be to secure the Safety Strap to a wall stud by using a #8 screw (not included). The length of the screw depends on the wall

thickness.

Second option would be to secure the Safety Strap to a wall anchor (not included) in the wall at the appropriate location. Follow the wall anchor’s

instructions for assembly.

MOUNTING INSTRUCTIONS:

A) Remove one Metal Cap with Threaded Stud from the upper back side of the clock. Keep the large white spacer in place.

B) Remove the Clear Rubber Washer from the Threaded Stud.

C) Place the Large Eyelet of the Safety Strap over the Metal Cap with Threaded Stud.

D) Install the Clear Rubber Washer onto the Metal Cap with Threaded Stud. Thread the Metal Cap back into the clock and nger tighten.

E) Determine the location for the mounting screw or wall anchor and complete installation.

F) Move the clock to its nal location and attach the Small Eyelet of the Safety Strap to the mounting screw or wall anchor.

Metal Cap with

Threaded Stud

Safety Strap

Small Eyelet

(attaches to wall)

Figure 13

Large Eyelet

Clear Rubber

Washer

497263

03/2021

This manual suits for next models

Other Howard Miller Clock manuals

Howard Miller

Howard Miller Seville User manual

Howard Miller

Howard Miller BEDFORD PARK Installation manual

Howard Miller

Howard Miller 615088 Installation manual

Howard Miller

Howard Miller LEWISBURG User manual

Howard Miller

Howard Miller WALL AND MANTEL CLOCK User manual

Howard Miller

Howard Miller 615-052 User manual

Howard Miller

Howard Miller 615116 Installation manual

Howard Miller

Howard Miller 615114 Installation manual

Howard Miller

Howard Miller 611274 Installation manual

Howard Miller

Howard Miller 615096 Installation manual

Howard Miller

Howard Miller 615100 Installation manual

Howard Miller

Howard Miller 615-069 User manual

Howard Miller

Howard Miller 61123 User manual

Howard Miller

Howard Miller MYDay 625-488 User manual

Howard Miller

Howard Miller 615010 User manual

Popular Clock manuals by other brands

Silicon Laboratories

Silicon Laboratories SI5324 manual

Heathkit

Heathkit GC-1005 Assembly manual

Oregon Scientific

Oregon Scientific PRYSMA RMR221P manual

Andrew O'Malley

Andrew O'Malley DOTKLOK Assembly instructions

ALGE-Timing

ALGE-Timing ASC3 manual

Bodet

Bodet Profil 960 Installation and operating instructions

Nixie Clock

Nixie Clock Divergence Meter user manual

La Crosse Technology

La Crosse Technology WS-8256-AL user manual

Mini Gadgets

Mini Gadgets MCPro user manual

Casio

Casio TMR-200 user guide

Progetti

Progetti ILTEMPOSTRINGE Directions

BVItech

BVItech BV-101 instruction manual

Progetti

Progetti KALIMERO Directions

La Crosse Technology

La Crosse Technology WT-3141b Quick setup instructions

La Crosse Technology

La Crosse Technology W86531 owner's manual

Sharp

Sharp SPC900 instruction manual

La Crosse Technology

La Crosse Technology 404-50447 quick start guide

Datexx

Datexx DF0063 quick guide