Hotpoint G155 User manual

wwv.Hotpoint.com

Safety Instructions .......... 2,s

Operating Instructions

Care and Cleaning

of the Washer ...................... 6

Control Panel ...................... 4

Control Settings ................... 4

Features ........................... 5

Loading and Using

the Washer ........................ 6

Troubleshooting Tips........ 7-9

Consumer Support

Consumer Support ................ 12

Warranty .......................... 11

Write the model and serial

number here:

Model #

Serial #

You can find them

under the lid of

the washer.

39-90436 02-12 GE

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

of fire or explosion, electric"shock, or to prevent property damage, personal injury, or

loss of life.

WATERHEATERSAFETY

Under certain conditions, hydrogen gas may be produced in awater heater that has not been

used for two weeks or more. Hydrogen gas can be explosive under these circumstances.

If the hot water has not been usedfor two weeks or more, prevent the possibility of damage or injury by

turning on all hot water faucets and allowing them to run for several minutes. Dothis before usingany

electrical appliance which isconnected to the hotwater system. Thissimple procedure will allow any

built-up hydrogen gasto escape.Sincethe gas isflammable, do not smoke or usean openflame or

appliance during this process.

PROPERINSTALLAflON

This washer must be properly installed and located in accordance with the Installation

instructions before it is used. If you did not receive an installation instructions sheet, you can

receive one by visiting www.Hotpoint.com or by calling 800.GE.CARES (800.432.2737).

• Installor store where it will not be exposed to • Thiswasher does not include water supply hoses.

temperatures below freezing or exposed to the

weather, which could cause permanent damage

and invalidate the warranty.

• Properlyground washer to conform with all

governing codes and ordinances. Follow details

in Installation Instructions.

• Toensureproper installation, run two small load

size Whites/Rinse cycles BEFOREwashing the first

load.

GEstrongly recommends the useof factory

specified parts.A list of factory hosesavailable

for purchase are listed below. Thesehoses

are manufactured and tested to meet GE

specifications.

GEstrongly recommends the useof new water

supply hoses.Hosesdegrade overtime and need

to be replaced every 5 years to reduce the risk of

hosefailures and water damage.

Parts and Accessories

Order on-line at GEAppliances.com today, 24

hours a day or by phone at 800.626.2002 during

normal businesshours.

Part Number

WH41X10207

Accessory

4 ft RubberWater Supply Hoses

YOURLAUNDRYAREA

• Keepthe area underneath and around your

appliances free of combustible materials such as

lint, paper, rags,chemicals, etc.

WX14X10005 4 ft Braided Water Supply Hoses

• Closesupervisionis necessaryif this appliance is

used by or near children.Do not allow children to

play on,with or insidethis or any other appliance.

www.Hotpoint.com

Use this

appliance

only for its

intended

purpose as

described in

this Owner's

Manua/

WHEN USINGTHEWASHER

Never reach into the washer while it ismoving.

Wait until the machine hascompletely stopped

before opening the lid.

Do not mix chlorine bleach with ammonia or

acids such as vinegar and/or rust remover. Mixing

different chemicals can produce a

toxic gas which may cause death.

Do not wash or dry articlesthat have been

cleaned in,washed in,soaked in or spotted with

combustible or explosivesubstances (suchas

wax, oil,paint, gasoline,degreasers,dry-cleaning

solvents,kerosene,etc.).Thesesubstances give

off vaporsthat may ignite or explode. Donot add

these substances to the wash water. Donot use

or placethese substancesaround your washer or

dryer during operation.

Thelaundry processcan reducethe flame

retardancy offabrics. To avoid such a result,

carefully follow the garment manufacturer's

wash and care instructions.

To minimizethe possibility of electric shock,

unplug this appliance from the power supply

or disconnect the washer at the building's

distribution panel by removing the fuse or

switching off the circuit breakerbefore attempting

any maintenance or cleaning.

NOTE:TurningtheCycleSelectorKnob to an off

position, or pressing PAUSEdoesNOT disconnect

theappliance from thepower supply,

Neverattempt to operate this appliance if it is

damaged, malfunctioning, partially disassembled,

or has missing or broken parts,including a

damaged cord or plug.

WHENNOTIN USE

• Turnoff water faucets to minimize leakage if a

break or rupture should occur.Checkthe condition

of the fill hoses;Hotpoint recommends changing

the hoses every 5 years.

• Beforediscarding a washer, or removing it

from service,remove the washer lid to prevent

children from hiding inside.

• Donot attempt to repair or replace any part of

this appliance unless specifically recommended in

this Owner's Manual, or in published user-repair

instructions that you understand and have the

skillsto carry out.

• Donot tamper with controls.

READAND FOLLOW THISSAFETYINFORMATION

CAREFULLY

THESE INSTRUCTIONS

About the control panel.

• Add detergent • Add items

• Select load size

• Select temperature

• Select wash cgcle

Step 4

• Close lid

• Pull knob

•Select options

LOAD SIZE TEMPERATURE OPTIONS

Controls

Load Size (on some models)

Looselyload items in the washer basket. Overloading may negatively impact wash performance. Adjust the load sizeaccordingly.

Temperature (on some models)

Selectthe water temperature for the wash and rinsecycles.Always follow fabric manufacturer's care labelor instructions when

laundering.

Options (on some models)

Fabric Softener and Power Rinse

Setthis option when planning to manually add fabric softener during the rinsecycle or when you useextra detergent or bleach to

clean heavily soileditems. It provides an enhanced rinse.

Wash Cgcle--Cgcle Selector Knob

Thechart below will help you match the wash cycle setting with your items.Thechart isranked from greatest to least wash intensity.

Your washer may not have all these cycles.

WHITES Forheavy to lightly soiledcottons, household linens,work and play clothes.

(REGULARWASH/FASTSPIN}

COLORSForheavy to lightly soiledcolors andjeans

(REGULARWASH/FASTSPIN}

PERMANENTPRESSForheavy to lightly soiledcottons, household linens,work and play clothes.

(PULSED/FASTSPIN}

About washer features, www.Hotpoint.com

Liquid Bleach Funnel

Thewater filldilutes liquid chlorine bleach as the washer fillsfor the wash cycle.

I_J Checkclothing care labelsfor special instructions.

r2] Measure liquid bleach carefully, following instructions on the bottle.

•Neverpour undiluted liquid chlorinebleach directly onto clothesor into the wash

basket,

• Donotpourpowdered bleach into bleachfunnel.

r_ Beforestarting the washer, pour measured amount of bleach directly into bleachfunnel.

Avoid splashing or over-filling dispenser.If you prefer to usepowdered bleach, add it into

the wash basketwith your detergent.

• Donot mix chlorinebleach with ammonia or acids suchas vinegarand/or rust

remover,Mixing canproduce a toxicgas which may cause death.

Liquid Fabric Softener (Manually add during rinse cycle)

I]1 Turn Options knobto Fabric Softener.

I_] Heasure liquid fabric softener carefully, following instructions on the bottle, and add during

the rinsecycle.

NOTE:The Options knob must be turned to Fabric Softener.

Q:What isthe difference between Heavyand Light settings?

A: ForWhites and Colors,the wash agitation time isincreased by 6minutes and for Permanent

Press,by 12 minutes. (Timesare approximate)

Q:What isthe difference between Regularand Pulsed?

A: Regularmeans the washer will continuously agitate during the wash cycle. Pulsedprovides a

more gentlewash cycleby including pause periodsduring the wash cycle.

Q:Which cycle isbest for heavily soiled items?

A:Whites or Colorscycles have the greatest wash intensity.Thiscycle provides the best overall

cleaning. Permanent Pressshould be used for wrinkle-free and permanent press items.

Q:How can Ireduce linting?

A:Sortwash loadsby fabric type and whether they collect lint (velveteen,corduroy) or produce

lint (terry cloth, chenille).Wash small loadsfor a shorter amount of time.

Q:How much detergent do Iuse?

A: Forbest performance, always follow the detergent manufacturer's instructions on usage.

Many detergents are concentrated, so consult the product label and follow the clearly

marked lineson the detergent measuring cups.Excessivedetergent can negatively impact

the wash performance.

Loading and using the washer.

Always follow fabric manufacturer's care label when laundering

Sorting WashLoads

Sort by color (whites,lights,colors),soillevel,

fabric type (sturdycottons, easy care, delicates)

and whether the fabric produces lint (terry cloth,

chenille)or collects lint (velveteen,corduroy).

Use

Add detergent before adding items sothat the

detergent can work effectively. Usingtoo little or

too much detergent isa common cause of laundry

problems.

Forspots,apply pre-treatment to items as

recommended on the product label. Application

should be made in the basket to prevent overspray

which may cause the coloring on the lid or graphics

to fade.

You can use lessdetergent ifyou have soft water,

a smaller load or a lightly soiledload.

When usinghigh efficiency or concentrated

detergents, consult the product label to determine

amount required for optimum performance.

Excessivedetergent will negatively impact wash

performance.

Loading the Washer

Load dry items loosely in the washer basket.When

loading wet items, make sure you set the load/water

levelhighenough to allow the itemsto move freely.

Water levelshouldjust cover the items.To add items

after washer hasstarted, lift the lid and submerge

additional items next to the agitator.

•Do not wrap long items like sheets orpants

around the agitator,

• Do not wash fabrics containing flammable

materials (waxes, cleaning fluids, etc,),

• Washer will not agitate or spin with the lid up,

however the timer will continue to run,

Care and cleaning of the washer.

Wash Basket: Leavethe lid open after washing to

allow moisture to evaporate. If you want to clean

the basket, usea cleansoft cloth dampened with

liquid detergent; then rinse.(Donot useharsh or

gritty cleaners.)

FillHoses: Hotpoint recommends changing the hoses

every 5 years.

Exterior: Immediately wipe off any spills.Wipe

with damp cloth.Try not to hit surface with

sharp objects.

Having and Storage: Askthe servicetechnician to

remove water from drain pump and hoses.Seethe

Installation Instructions packed with product for

information on how to reinstallthe shipping rod

to keep the tub stationary when moving the washer.

Formore information, visit www.Hotpoint.com or

call 800.GE.CARES(800.4:32.2737).Donot store the

washer where it will be exposed to the weather.

Long Vacations: Besurewater supply isshut off at

faucets. Drainall water from hosesif weather will

be below freezing.

Before you call for service.., www.Hotpoint.com.

_roubleshooting Tips

Save time and money! Review the charts on the following pages,

or visit www.Hotpoint.com. Youmay not need to call for service.

WATER Possible Causes What To Do

Too many suds Toomuch detergent • Measureyour detergent carefully. Uselesssoap ifyou have

soft water, a smaller load or a lightly soiledload.

Tgpe of detergent • Switch to a lower sudsing detergent brand and follow

instructions on package.

Soft water • Try lessdetergent.

Water leaks Using too much detergent • Uselessdetergent. Uselesssoap ifyou have soft water,

in washer a smaller load or a lightly soiledload.

Fillhoses or drain hose is • Makesure hoseconnections are tight at faucets and

improperly connected rubber washers are installed.Make sure end of drain hose

iscorrectly inserted in and secured to drain facility.

Household drain mag •Checkhousehold plumbing. You may need to call

be clogged a plumber.

Drain hose loose • Makesure drain hose isfully seated in back ofwasher and

that the two retaining screws are fully seated.

Drain hose rubs on wall • Makesure drain hosedoes not make contact with the wall.

May cause excessivewear on the hose.

Constant water pressure • Tightenhoses at the faucets and turn the water off after

to the fill hoses at the each use.

water source • Checkcondition of the fill hoses;they should be replaced

every 5years.

Water temperature Cooler water temperatures • New laundry detergents have been formulated to work

seems incorrect provide improved energg with cooler water temperatures without affecting wash

efficiencg performance.

Water supplg is turned off • Turn both hot and cold faucets fully on and make sure

or improperlg connected hoses are connected to correct faucets.

Water valve screens are • Turn off the water source and remove the water connection

stopped up hoses from the upper back of the washer. Use a brush or

toothpick to clean the screens in the machine. Reconnect

the hoses and turn the water back on.

Housewater heater is • Hake sure housewater heater isdeliveringwater at

not set properlg 120°F-140°F(48°C-60°C).

Water pumped out before Lid lifted or cgcle was put in • Resetcycle.

cycle is complete pause for over 24 hours

Water won't drain Drain hose is kinked or • Straighten drain hoseand make surewasher isnot

improperlg connected sitting on it.

• Topof drain outlet should be lessthan 6 ft (1.8m)

above floor.

Washer pauses during This isnormal • Thisis normal. Thewasher alternates between agitate and

wash cycle soak during some wash cyclesto get your clothes cleanerwith

lesswear.

Washer pauses during This isnormal • Thewasher may pause during the spin cycleto remove

spin cycle soapy water more efficiently.

Before gou call for service...

OPERATION Possible Causes What To Do

Washer won't operate Washer is unplugged •Hake sure cord is plugged securely into aworking outlet.

Water supply isturned off • Turn both hot and coldfaucets fully on.

Controls are not set properly • Checkcontrols.

Lid isopen--safety feature • Closelid and reset cycle,to the beginning if necessary.

prevents agitation and

spinning when lid is up

Circuit breaker/fuse is • Checkhouse circuit breakers/fuses. Replacefuses or

tripped/blown reset breaker. Washer should haveseparate outlet.

Timer knob not pulled • Pulltimer knob.

Lid magnet missing • Callfor service.

Movement inside machine Shifting mechanism is • When the machine ismanually turned off,the shifter will

when shut off disengaging the motor disengage the motor before completely shutting down.

If lid israised beforethe motor isdisengaged, it will resume

when lid isclosed.

PERFORMANCE Possible Causes What To Do

Clothes too wet Incorrect spin cgcle • Hake sure the spin cycleselected matches the load you ore

selected washing.Somefabricswillfeelwetter when rinsedwith coldwater.

Colored spots Incorrect useoffabric • Checkfabric softener package for instructions.

softener • Pretreat stain and rewash.

Dge transfer • Sortwhites or lightly colored items from dark colors.

Grayed oryellowed Not enoughdetergent • Use more detergent (especiallywith larger loads).

clothes Be sureto follow detergent manufacturer's directions.

Hard water • Useo water conditioner likeCalgon brand or install

a water softener.

Water is not hot enough • Hake sure water heater isdelivering water at

120°F-140°F(48°C-60°C).

Washer is overloaded • Selectload sizeto match clothes load.

Detergent is not • Add detergent beforeyou load items.

dissolving

Dge transfer • Sortclothes bycolor. Iffabric label states wash separately,

unstable dyes may be indicated.

Lint or residue on Clothes are air or line dried • If you do not dry your clotheswith a clothes dryer,your

clothes clothes may retain more lint.

Incorrect sorting • Separate lint producersfrom lint collectors.

Washing too long • Washsmall loadsfor a shorter time than larger loads.

Detergent not dissolving • Add detergent beforeyou load items.

• Try a liquid detergent.

• Usewarmer water temperature.

Overloading • Load clothes loosely in the washer basket.Adjustload size

based on items sizeand material.

• Makesure load sizeselectedmatches clothes load size.

Incorrect use offabric • Checkfabric softener package for instructions.

softener

www.Hotpoint.com

PERFORMANCE (cont.) Possible Causes What To Do

Pilling Result of normal wear on •While this isnot caused bythe washer,you can slow the

polg-cotton blends and pilling processby washing garments insideout.

fuzzg fabrics

Snags, holes, tears, rips

or excessivewear Pins,snaps, hooks, sharp • Fastensnaps,hooks,buttons and zippers.

buttons, belt buckles, • Removelooseitems like pins,objects in pockets and

zippers and sharp objects sharp buttons.

left in pockets • Turn knits (whichsnag easily)inside out.

Undiluted chlorine bleach • Check bleach package instructions for proper amount.

• Never add undiluted bleach to wash or allow clothesto

come in contact with undiluted bleach.

Chemicals like hair bleach or • Rinseitems that may have chemicals on them before

dge,permanent wave solution washing.

Wrinkling Improper sorting • Avoid mixing heavy items (likework clothes)with light items

(likeblouses).

• Try a fabric softener.

Overloading or incorrect • Loadyour washer so clothes haveenough room to move

water level freely with water covering all ofthe clothes.

Incorrect wash and • Hatch Cycleselectionto the type of fabricyou are washing

drg cgcles (especiallyfor easy care loads).

Repeated washing in • Wash in warm or coldwater.

water that istoo hot

SOUNDS Possible Causes Reason

"Metallic clicking" Shifter mechanism is • Thedrive system will engage at the start of agitate and

engaging or disengaging disengage when agitate iscomplete. Thisoccurs multiple

times during the wash.

Back and forth "swoosh" Electric motor reversing • Thismachine hasa drive system that doesn't usegears.

or light "clicking" sound direction Thissound isthe motor rotating back and forth to clean

during agitate your laundry.

"Click" when water Relagswitch • Therelay makes a clicksound when activated. Thewater

stops filling levelactivates the relayand stops filling.

"Clicking" behind Contro/ Automatic Temperature • Twovalvesmix cold and hot water.The"clicking"iswhen either

Panel during fill Control Valve valve turns on or off to raiseor lowerthe fill water temperature.

Water flow changes Automatic Temperature • Twovalvesmix coldand hotwater.Theflow changeswheneither

during fill Control Valve valve turns on or off to raiseor lowerthe fill water temperature.

Motor "whining up" or Motor ramping up/down • Themotor will speed up incrementally duringthe spin cycle.

"coasting down" in spin during spin cgcle When spin iscomplete, it will coast until it stops.

"Humming" Water drain pump • Thedrain pump will make a humming sound when pumping

out water after agitation stopsand continue until spin is

complete.

"Gurgling" Water drain pump • When the pump starts drawing inair, It starts to gurgle.

Thewasher should then begin spinning and the sound will

continue until it isdone spinning.

Washer is noisy Washer isuneven • To levelthe front of the washer,adjust the front levelinglegs

by rotating the individual leg in the proper direction for up

or down. To levelthe back of the washer, lift the back of the

machine 4"(11cm) and set down.

Shipping rod is still assembled • Toremove the shipping rod from the washer, pull theyellow

in the unit tag and removethe attached rod from the bottom right hand

side of the washer.

Notes...

Other manuals for G155

Table of contents

Languages:

Other Hotpoint Washer manuals

Hotpoint

Hotpoint WMPF 823 User manual

Hotpoint

Hotpoint AQUARIUS WM61 User manual

Hotpoint

Hotpoint HNSR4150 User manual

Hotpoint

Hotpoint WM12 User manual

Hotpoint

Hotpoint AQUARIUS WMAQC 641 User manual

Hotpoint

Hotpoint ultima digit wt640 User manual

Hotpoint

Hotpoint 800 SUPER 9511 Instruction Manual

Hotpoint

Hotpoint NM11946WSAUKN User manual

Hotpoint

Hotpoint FEW10 User manual

Hotpoint

Hotpoint HTWP1000M0WW User manual

Hotpoint

Hotpoint ARTXL 109 User manual

Hotpoint

Hotpoint WD42 Instruction Manual

Hotpoint

Hotpoint WMD 962A User manual

Hotpoint

Hotpoint 9773 Instruction Manual

Hotpoint

Hotpoint Experience WMEF 7225 User manual

Hotpoint

Hotpoint AQUALTIS AQ93F 29 User manual

Hotpoint

Hotpoint HF8B 593 User manual

Hotpoint

Hotpoint WMUD 943 User manual

Hotpoint

Hotpoint 772268 User manual

Hotpoint

Hotpoint WMJLD 943 User manual

Hotpoint

Hotpoint AQGL129PI User manual

Hotpoint

Hotpoint AQXXL129PI Instruction manual

Hotpoint

Hotpoint WMFG 1053 User manual

Hotpoint

Hotpoint AQXXF 149 H PI User manual

Popular Washer manuals by other brands

Tricity Bendix

Tricity Bendix AW 1000 W Operating & installation instructions

Panasonic

Panasonic NA-F60L5WRB operating instructions

GE WSLP1500 Dimensions and installation information

Electrolux

Electrolux EWF1284EDW Service manual

Bosch

Bosch WAN2829BSN User manual and installation instructions

LG TV2516DV3B owner's manual

LG TH2517DSAV owner's manual

VESTEL

VESTEL CMH-XL 7510 TE user manual

AEG

AEG 74335 User information

Johnson

Johnson JWF721A user manual

Beko

Beko WTE7604XLW0 owner's manual

Danby

Danby DTT100A1WDB Owner's use and care guide

Amica

Amica WA 14 Ex operating instructions

Daewoo

Daewoo DWD-F1222 instruction manual

Bosch

Bosch WAS28461AU instruction manual

Miele

Miele PW 6080 Vario manual

Finlux

Finlux FLX108CF220 user manual

Whirlpool

Whirlpool 3LBR5132AN0 Use and care guide