Hotpoint WDL520P User manual



English, 1

Contents

Installation, 2-3-4-5

Unpacking and levelling

Connecting the electricity and water supplies

The first wash cycle

Technical data

Description of the Washer-dryer and

starting a ash cycle, 6-7

Control panel

Indicator lights

Starting a wash cycle

Wash cycles, 8

Table of wash cycles

Personalisation, 9

Setting the temperature

Setting the drying cycle

Functions

Detergents and laundry, 10

Detergent dispenser drawer

Preparing the laundry

arments requiring special care

Load balancing system

Precautions and tips, 11

eneral safety

Disposal

Opening the porthole door manually

Care and maintenance, 12

Cutting off the water or electricity supply

Cleaning the Washer-dryer

Cleaning the detergent dispenser drawer

Caring for the door and drum of your appliance

Cleaning the pump

Checking the water inlet hose

Troubleshooting, 13

Assistance, 14

WDL 520 P/G/A/K

Instructions for use

WASHER-DRYER

All manuals and user guides at all-guides.com

all-guides.com

Installation

Levelling your appliance correctly will provide it with

stability and avoid any vibrations, noise and shifting

during operation. If it is placed on a fitted or loose

carpet, adjust the feet in such a way as to allow

enough room for ventilation beneath the washing

machine.

Electric and ater connections

Connecting the ater inlet hose

1. Connect the supply

pipe by screwing it to a

cold water tab using a

3/4 gas threaded

connection (see figure).

Before performing the

connection, allow the

water to run freely until

it is perfectly clear.

2. Connect the other end

of the water inlet hose to

the washing machine,

screwing it onto the

appliance's cold water

inlet, situated on the top

right-hand side on the

rear of the appliance (see

figure).

3. Make sure there are no kinks or bends in the hose.

!The water pressure at the tap must be within the

values indicated in the Technical details table

(on the next page).

!If the water inlet hose is not long enough, contact

a specialist store or an authorised serviceman.

!Ensure that the supply taps are allowing water

through. Old taps may seize in the closed position

and thus prevent water reaching the machine.

!Keep this instruction manual in a safe place for

future reference. Should the appliance be sold,

transferred or moved, make sure the instruction

manual accompanies the washing machine to inform

the new owner as to its operation and features.

!Read these instructions carefully: they contain

vital information on installation, use and safety.

Unpacking and levelling

Unpacking

! This a part of the

polystirene base and

should have stayed

intact when you

removed the base.

! IMPORTANT check

hen unpacking your

machine.

1. Unpack the washing machine.

2. Check whether the washing machine has been

damaged during transport. If this is the case, do

not install it and contact your retailer.

3. Remove the 4

protective screws and

the rubber bush with the

respective spacer,

situated on the rear of

the appliance (see also

the installation leaflet).

4. Do not remove external bar.

5. Seal the gaps using the plastic plugs provided.

6. Keep all the parts: you will need them again if the

washing machine needs to be moved to another

location.

!Packaging materials are not children's toys.

Levelling

Your machine may make a considerable amount of noise

if the two front feet have not been adjusted correctly.

1. Install the washing

machine on a flat sturdy

floor, without resting it

up against walls, furniture

cabinets or other.

2. If the floor is not perfectly level, compensate for

any unevenness by tightening or loosening the

adjustable front feet (see figure); the angle of

inclination, measured according to the worktop,

must not exceed 2°.

All manuals and user guides at all-guides.com

_the supply voltage is included within the values

indicated on the Technical details table

(see page 5);

_the socket is compatible with the washing

machine's plug. If this is not the case, replace

the socket or the plug.

Your appliance is now supplied with a 13 amp fused

plug it can be plugged into a 13 amp socket for

immediate use. Before using the appliance please

read the instructions below.

WARNIN - THIS APPLIANCE MUST BE EARTHED.

THE FOLLOWIN OPERATIONS SHOULD BE CARRIED

OUT BY A QUALIFIED ELECTRICIAN.

Replacing the fuse:

When replacing a faulty fuse, a 13 amp ASTA

approved fuse to BS 1362 should always be used,

and the fuse cover re-fitted. If the fuse cover is

lost, the plug must not be used until a replacement

is obtained.

Replacement fuse covers:

If a replacement fuse cover is fitted, it must be of

the correct colour as indicated by the coloured

marking or the colour that is embossed in words on

the base of the plug. Replacements can be obtained

directly from your nearest Service Depot.

Removing the plug:

If your appliance has a non-rewireable moulded plug

and you should wish to re-route the mains cable

through partitions, units etc., please ensure that

either:

the plug is replaced by a fused 13 ampere re-

wearable plug bearing the BSI mark of approval.

or:

the mains cable is wired directly into a 13 amp cable

outlet, controlled by a switch, (in compliance with

BS 5733) which is accessible without moving the

appliance.

Disposing of the plug:

Ensure that before disposing of the plug itself, you

make the pins unusable so that it cannot be

accidentally inserted into a socket.

Instructions for connecting cable to an alternative

plug:

Important: the wires in the mains lead are coloured

in accordance with the following code:

Green & Yello Earth

Blue Neutral

Bro n Live

65 - 100 cm

Where it connects to

the waste water pipe

cut end off spigot or

remove the blanking cap

Connecting the drain hose

Connect the drain

hose, without bending

it, to a draining duct or

a wall drain situated

between 65 and 100 cm

from the floor;

The drain hose may be

connected to an under-

sink trap. Before

connecting the drain

hose from the machine

ensure that any blanks

or removable ends have

been taken off the

spigot.

If it is place over the

edge of a basin or sink

be sure the free end

of the hose should not

be underwater.

! We advise against the use of hose extensions; in

case of absolute need, the extension must have

the same diameter as the original hose and must

not exceed 150 cm in length.

Ensure that if the drain hose is pushed into a

standpipe, that the end does not go down more

than 15cms (6 inches). If the hose is pushed down

too far, this may cause the machine to self -

syphon ie. continuously empty as it is filling.

Electric connection

Before plugging the appliance into the mains

socket, make sure that:

_the socket is earthed and in compliance with

the applicable law;

_the socket is able to sustain the appliance's

maximum power load indicated in the Technical

details table (see page 5);

All manuals and user guides at all-guides.com

As the colours of the wires in the lead may not

correspond with the coloured markings identifyng

the terminals in your plug, proceed as follows:

Connect reen & Yellow wire to terminal marked E

or or coloured reen or reen & Yellow.

Connect Brown wire to terminal marked L or

coloured Red.

Connect Blue wire to terminal marked N or coloured

Black.

If a 13 amp plug (BS 1363) is used it must be fitted

with a

13 amp fuse, either in the plug or adaptor or at the

distribution board.

If you are in any doubt the electrical supply to your

machine, consult a qualified electrician before use.

How to connect an alternative plug:

The wires in this mains lead are coloured in

accordance with the following code:

BLUE NEUTRAL (N)

BROWN LIVE (L)

GREEN & YELLOW EARTH (E)

Disposing of the appliance:

When disposing of the appliance please remove the

plug by cutting the mains cable as close as possible to

the plug body and dispose of it as described above.

! The Washer-dryer should not be installed in an

outdoor environment, not even when the area is

sheltered, because it may be very dangerous to

leave it exposed to rain and thunderstorms.

! When the Washer-dryer is installed, the mains

socket must be within easy reach.

! Do not use extensions or multiple sockets.

! The power supply cable must never be bent or

dangerously compressed.

! The power supply cable must only be replaced by

an authorised serviceman.

Warning! The company denies all liability if and

when these norms are not respected.

The first ash cycle

Once the appliance has been installed, and before

you use it for the first time, run a wash cycle with

detergent and no laundry, using the wash cycle 1.

GREEN &

YELLOW

BROWN

BLUE

13 ampere fuse

CROSS-BAR

CORD GRIP

All manuals and user guides at all-guides.com

Technical data

Model WDL 520 P/ /A/K

Dimensions

width 59.5 cm

height 85 cm

depth 53.5 cm

Capacity from 1 to 7 kg for the wash programme

from 1 to 5 kg for the drying programme

Electrical

connections

please refer to the technical data

plate fixed to the machine

Water

connections

maximum pressure 1 MPa (10 bar)

minimum pressure 0.05 MPa (0.5 bar)

drum capacity 52 litres

Spin speedup to 1200 rotations per minute

Energy

rated

programm-

according

regulation

EN 50229

Wash : programme 1; temperature

60°C; using a load of 7 kg;

Drying: first drying cycle performed with

a 2 kg load, by selecting the dryness

level;

the second drying cycle is performed

with a 5 kg load, by selecting the

dryness level.

This appliance conforms to the

following EC Directives:

- 89/336/EEC dated 03/05/89

(Electromagnetic Compatibility) and

subsequent modifications

- 2002/96/EC

- 2006/95/EC (Low Voltage)

All manuals and user guides at all-guides.com

Description of the Washer-dryer and

starting a ash cycle

Detergent dispenser drawer: used to dispense

detergents and washing additives (see Detergents

and laundry).

ON/OFFbutton: switches the Washer-dryer on

and off.

WASH CYCLEknob: programmes the wash cycles.

During the wash cycle, the knob does not move.

FUNCTION buttons with indicator light: used to

select the available functions. The indicator light

corresponding to the selected function will remain lit.

TEMPERATURE knob: sets the temperature or the

cold wash cycle (see Personalisation).

DRYINGknob: used to set the desired drying

programme (see Personalisation).

WASH CYCLE PROGRESS

indicator light

s:used

to monitor the progress of the wash cycle.

The illuminated indicator light shows which phase is

in progress.

DOOR LOCKEDindicator light: indicates whether

the door may be opened or not (see next page).

START/PAUSE button with indicator light: starts

or temporarily interrupts the wash cycles.

N.B. To pause the wash cycle in progress, press this

button; the corresponding indicator light will flash

orange, while the indicator light for the current

wash cycle phase will remain lit in a fixed manner. If

the DOOR LOCKED indicator light is switched

off, the door may be opened.

To start the wash cycle from the point at which it

was interrupted, press this button again.

Standby mode

This washing machine, in compliance with new

energy saving regulations, is fitted with an

automatic standby system which is enabled after a

few minutes if no activity is detected. Press the

ON-OFF button briefly and wait for the machine to

start up again.

TEMPERATURE

knob

Detergent dispenser drawer

WASH CYCLE PROGRESS

indicator lights

FUNCTION

buttons with

indicator lights

ON/OFF

button

DRYING

knob

DOOR

LOCKED

indicator light

START/PAUSE

button with

indicator light

Control panel

WASH CYCLE

knob

All manuals and user guides at all-guides.com

all-guides.com

Indicator lights

The indicator lights provide important information.

This is what they can tell you:

Wash cycle phase indicator lights

Once the desired wash cycle has been selected and has

begun, the indicator lights switch on one by one to

indicate which phase of the cycle is currently in progress.

Note: during the "Drain" phase, the indicator light

corresponding to the "Spin" cycle phase will illuminate.

Function buttons and corresponding

indicator lights

When a function is selected, the corresponding

indicator light will illuminate.

If the selected function is not compatible with the

programmed wash cycle, the corresponding indicator

light will flash and the function will not be activated.

If a function which is incompatible with another

function selected previously, only the most recent

selection will remain active.

Door locked indicator light

If this indicator light is on, the appliance door is locked

to prevent it from being opened accidentally; to avoid

any damage, wait for the indicator light to switch off

before you open the appliance door.

! If the START/PAUSE indicator light (orange)

flashes rapidly at the same time as the function

indicator light, this indicates a problem has

occurred (see  roubleshooting).

Starting a ash cycle

1. Switch the washing machine on by pressing the ON/OFF button. All the indicator lights will turn on for a few

seconds, then only the indicator lights relative to the selected programme settings will remain lit and the

START/PAUSE indicator light will flash.

2. Load the laundry and close the door.

3. Set the WASH CYCLE knob to the desired programme.

4. Set the washing temperature (see Personalisation).

5. Set the drying cycle if necessary (see Personalisation).

6. Measure out the detergent and washing additives (see Detergents and laundry).

7. Select the desired functions.

8. Start the wash cycle by pressing the START/PAUSE button and the corresponding indicator light will remain

lit in a fixed manner, in green.

To cancel the set wash cycle, pause the machine by pressing the START/PAUSE button and select a new cycle.

9. At the end of the wash cycle the indicator light will switch on. The DOOR LOCKED indicator light will

switch off, indicating that the door may be opened. Take out your laundry and leave the appliance door ajar to

make sure the drum dries completely. Switch the Washer-dryer off by pressing the ON/OFF button.

Wash

Rinse

Spin

Dry

End of wash cycle

No e: as soon as a drying

level or time period has

been set, this indicator

light illuminates to indicate

that the selected wash

cycle will be followed by a

drying phase.

All manuals and user guides at all-guides.com

Wash cycles

Table of ash cycles

Descrip ion of he wash cycle

Max.

emp.

(°C)

Max.

speed

(rpm)

Drying

De ergen s Max. load

(kg)

Cycle

dura ion

Wa sh Fabric

sof ener Normal Mini

load Normal Mini

load

Essentials cycles

1Co on: extremely soiled whites. 90° 1200 ll l 7 3 141 111

1Co on (1): extremely soiled whites. 60° 1200 ll l 7315998

1Co on: heavily soiled whites and delicate colours. 40° 1200 ll l 7 3 115 91

2Co on: heavily soiled whites and resistant colours. 60° 1200 ll l 7312298

2Co on (2): heavily soiled whites and delicate colours. 40° 1200 ll l 7 3 115 91

3Coloured Co ons (3): lightly soiled whites and delicate colours. 40° 1200 ll l 738571

4Syn he ics: heavily soiled resistant colours. 50° 800 ll l 31,58263

5Fas wash 60': to refresh lightly soiled garments quickly

(not suitable for wool, silk and clothes which require washing by hand). 60° 1200 ll l 3-60 -

Specials cycles

6Baby cycle: heavily soiled delicate colours. 40° 800 ll l 2 1 118 97

7Shir s 40° 600 ll l 2 1 69 65

8Ready o wear (*) 30° 800 ll l 1-60 -

9Wo ol : for wool, cashmere, etc. 40° 800 ll l 1,5 1 55 51

10 Silk: for garments in silk and viscose, lingerie. 30° 0 -ll 2 1 55 51

Drying cycles

11 Drying Cottons - - l- - 5- - -

12 Drying Synthetics - - l- - 3- - -

13 Drying Wool - - l- - 1,5 - - -

Partials ash cycles

ARinse Fast -1200 l-l7 3 36 32

BSpin Fast -1200 l- - 7-16 -

CPump out -0- - - 7-2-

he information contained in the table is intended as a guide only.

For all Tes Ins i u es:

1) Tes wash cycle in compliance wi h regula ion EN 50229: se wash cycle 1 wi h a empera ure of 60°C.

2) Long wash cycle for co ons: se wash cycle 2 wi h a empera ure of 40°C.

3) Shor wash cycle for co ons: se wash cycle 3 wi h a empera ure of 40°C.

(*) Ready to Wear

This cycle was designed to wash and dry lightly soiled small loads quickly. By selecting this cycle it is possible to

wash and dry a maximum load of 1 kg in just 60 minutes.

Please note, this is an automatically programmed wash and dry cycle, therefore it is not possible to manually

set a drying time or drying level in conjunction with this cycle.

Please note, the Drying indicator illuminates only during the drying phase of the cycle, not when the cycle is

first selected.

All manuals and user guides at all-guides.com

Personalisation

Setting the temperature

Turn the TEMPERATURE knob to set the wash temperature (see able of wash cycles).

The temperature may be lowered, or even set to a cold wash ( ).

The Washer-dryer will automatically prevent you from selecting a temperature which is higher than the

maximum value set for each wash cycle.

Setting the drying cycle

Turn the DRYIN knob to set the desired drying type.

Two options are available:

A - Based on time: from 40 to 180 minutes.

B - Based on the how damp the clothes are once they have

been dried:

Iron : slightly damp clothes, easy to iron.

Hanger : dry clothes to put away.

Cupboard : very dry clothes, recommended for towelling

and bathrobes.

If your laundry load to be washed and dried is much greater than the maximum stated load (see adjacent

table), perform the wash cycle, and when the cycle is complete, divide the garments into groups and put some

of them back in the drum. At this point, follow the instructions provided for a "Drying only" cycle. Repeat this

procedure for the remainder of the load.

N.B: when the drying is complete there is a cooling period, even though the DRYIN knob is in the position.

Drying only

Turn the WASH CYCLE knob to one of the drying settings (11-12-13) according to the type of fabric, then

select the desired drying duration using the DRYIN knob.

Functions

The various wash functions available with this Washer-dryer will help to achieve the desired results, every time.

To activate the functions:

1. Press the button corresponding to the desired function;

2. the function is enabled when the corresponding indicator light is illuminated.

Note: If the indicator light flashes rapidly, this signals that this particular function may not be selected in

conjunction with the selected wash cycle.

Slo Spin (1200-600)

By selecting this function, reduces the spin speed.

 This function may not be used in conjunction with wash cycles 8, 10, 11, 12, 13, C.

Mini load

This function is recommended for when the load of laundry is equal to half, or less than half, of the maximum

recommended load (see able of wash cycles).

 This function may not be used in conjunction with wash cycles 5, 8, 11, 12, 13, B, C.

Extra rinse

By selecting this function, the efficiency of the rinse is increased and optimal detergent removal is

guaranteed. It is particularly useful for sensitive skin.

 This function may not be used in conjunction with wash cycles 8, 11, 12, 13, B, C.

Super Wash

Because a greater quantity of water is used in the initial phase of the cycle, and because of the increased

cycle duration, this function offers a high-performance wash.

 This function may not be used in conjunction with wash cycles 5, 8, 9, 10, 11, 12, 13, A, B, C.

Fabric

ype

Load ype Max.

load

(kg)

Cupboard

dry

Henger

dry

Iron

dry

Cotton Clothing of different

sizes, Terry towels 5180170160

Synthe-

tics

Sheets, Shirts, Pyjamas,

socks, etc. 3180170160

Wool Knitwear, Pullovers, etc. 1,5 150 140 130

Table of Drying times (guideline values)

All manuals and user guides at all-guides.com



Detergents and laundry

Detergent dispenser dra er

ood washing results also depend on the correct

dose of detergent: adding too much detergent will

not necessarily result in a more efficient wash, and

may in fact a build up on the inside of your appliance

and contribute to environmental pollution.

! Do not use hand washing detergents because

these create too much foam.

Open the detergent

dispenser drawer and

pour in the detergent or

washing additive, as

follows.

! Do not pour detergent into the middle compartment (*).

Detergent should only be poured into the compartment 1.

compartment 1: Detergent for the ash

cycle (po der or liquid)

For best results liquid detergent should be poured

in the dispenser immediately before the start of

the programme.

compartment 2: Additives (fabric softeners, etc.)

The fabric softener should not overflow the grid.

Preparing the laundry

 Divide the laundry according to:

- the type of fabric/the symbol on the label

- the colours: separate coloured garments from

whites.

 Empty all garment pockets and check the buttons.

 Do not exceed the listed values, which refer to

the weight of the laundry when dry:

Durable fabrics: max. 7 kg

Synthetic fabrics: max. 3 kg

Delicate fabrics: max. 2 kg

Wool: max. 1,5 kg

Ho much does your laundry eigh?

1 sheet 400-500 g

1 pillow case 150-200 g

1 tablecloth 400-500 g

1 bathrobe 900-1200 g

1 towel 150-250 g

Garments requiring special care

Baby cycle: this wash cycle 6 can be used to

remove the soiling typically caused by babies, while

ensuring that all detergent is removed from

nappies in order to prevent the delicate skin of

babies from suffering allergies. The cycle has been

designed to reduce the amount of bacteria by using

a greater quantity of water and optimising the

effect of special disinfecting additives added to the

detergent.

At the end of the wash cycle, the machine will slowly

rotate the drum to prevent the formation of

creases; to end the cycle press the START/PAUSE

button.

Shirts: use special wash cycle 7 to wash shirts in

various fabrics and colours.

It guarantees maximum care is taken of the

garments and minimises the formation of creases.

Wool: Hotpoint is the only Washer-dryer

manufacturer to have been awarded the

prestigious Woolmark Platinum Care endorsement

(M.0508) by the Woolmark Company, which means

that all woollen garments may be washed in the

Washer-dryer, even those which state hand wash

only on the label. Wash cycle 9 therefore offers

complete peace of mind when washing woollen

garments in the Washer-dryer (max. load 1,5 kg) and

guarantees optimal performance.

Silk: use special wash cycle 10 to wash all silk

garments. We recommend the use of special detergent

which has been designed to wash delicate clothes.

Curtains: fold curtains and place them in a pillow

case or mesh bag. Use wash cycle 10.

Load balancing system

Before every spin cycle, to avoid excessive vibrations

and to distribute the load in a uniform manner, the

drum rotates continuously at a speed which is slightly

greater than the washing rotation speed. If, after

several attempts, the load is not balanced correctly,

the machine spins at a reduced spin speed. If the load

is excessively unbalanced, the Washer-dryer per-

forms the distribution process instead of spinning.

To encourage improved load distribution and balance,

we recommend small and large garments are mixed

in the load.

All manuals and user guides at all-guides.com

Other manuals for WDL520P

This manual suits for next models

Table of contents

Other Hotpoint Washer Dryer manuals

Hotpoint

Hotpoint WDUD 9640 User manual

Hotpoint

Hotpoint WDL 5290 P User manual

Hotpoint

Hotpoint Aquarius WD420P Operating and installation instructions

Hotpoint

Hotpoint 9924 Instruction Manual

Hotpoint

Hotpoint FDEU9640P User manual

Hotpoint

Hotpoint WDAL 8640 User manual

Hotpoint

Hotpoint WDD 960 P User manual

Hotpoint

Hotpoint AQD970F 69 User manual

Hotpoint

Hotpoint WDL520P User manual

Hotpoint

Hotpoint BHWD 129 User manual

Hotpoint

Hotpoint Aquarius Plus+ WD640P Operating and installation instructions

Hotpoint

Hotpoint AQM8F 49 U User manual

Hotpoint

Hotpoint AQUALTIS AQD1170F 697 E User manual

Hotpoint

Hotpoint WDD 10760 User manual

Hotpoint

Hotpoint Aquarius WDL 756 P/G/A/K User manual

Hotpoint

Hotpoint AQUALTIS AQGMD 129 User manual

Hotpoint

Hotpoint Ultima 6kg Ultima User manual

Hotpoint

Hotpoint WDF 740 P User manual

Hotpoint

Hotpoint RG 964 J User manual

Hotpoint

Hotpoint WDF740A User manual

Hotpoint

Hotpoint WDL540 P/G/A/K User manual

Hotpoint

Hotpoint BHWD129 User manual

Hotpoint

Hotpoint BHWD 129 User manual

Hotpoint

Hotpoint Aqualtis AQGMD149 User manual

Popular Washer Dryer manuals by other brands

Whirlpool

Whirlpool WFC8090GX Use and care guide and installation instructions

Whirlpool

Whirlpool LTE5243DQ6 User instructions

Bosch

Bosch XQG100-WDU285H00W User manual and installation instructions

montpellier

montpellier MWD7512S Installation and operating instructions

LG FHD0905 T Series owner's manual

Midea

Midea MF200D85B owner's manual

Maytag

Maytag MGT3800XW installation instructions

Siemens

Siemens WD15G440TR Instruction manual and installation instructions

Equator

Equator Clothes Processor EZ1500 owner's manual

Splendide

Splendide WDC7100XCP Specifications

John Lewis

John Lewis JLWD 1408 instruction manual

Ariston

Ariston A1200WD Instruction booklet

Whirlpool

Whirlpool YLTE5243DQ5 installation instructions

Whirlpool

Whirlpool WFCR 75230 Health & safety, use & care and installation guide

ATT

ATT Hammer Jet v1 operating manual

AEG

AEG LAVAMAT 63742 VI Instruction booklet

Electrolux

Electrolux EWW8024P5WB user manual

GE GTD42EASJWH owner's manual