Honeywell Y87RF User manual

After ve seconds the current room temperature will be

displayed once again. The thermostat will then try to

maintain your set temperature as accurately as possible.

You can check your set temperature by turning the dial one ‘click’

to the left or right. The set temperature will ash up for a few

seconds, before returning to display the room temperature again.

Setting your room temperature

Your current room temperature is shown in the display.

To set the temperature you want, just turn the dial

right to increase and left to decrease. Each ‘click’

as the dial turns represents a 0.5º change.

User Guide

Single Zone Thermostat

Y87RF

User Guide

Single Zone Thermostat

Y87RF

Night-time temperature reduction

Overnight, or if you are out, it is best to set the thermostat to

a lower temperature, as it will save you energy. In general a

reduction of 5°C is recommended, but this will depend on your

heating system and the amount of insulation in your home.

Replacing the batteries

Your batteries should be replaced

when the symbol is displayed.

To do this, separate the thermostat

from the wiring plate and insert 2

new AA alkaline batteries in place

of the empty ones. Then reattach

the thermostat to the wiring plate.

Getting to know your display

Set Temperature Indicator

Means the gure on the screen is your set temperature,

rather than your current room temerature.

Heating on

Means there is a requirement for some heating, so

your boiler should either be on or cycling on/off.

Boiler Relay Connection

Means your thermostat is successfully

connected to your Boiler Relay.

Internet Gateway Connection (optional)

Means your thermostat is successfully

connected to your Internet Gateway.

After ve seconds the current room temperature will be

displayed once again. The thermostat will then try to

maintain your set temperature as accurately as possible.

You can check your set temperature by turning the dial one ‘click’

to the left or right. The set temperature will ash up for a few

seconds, before returning to display the room temperature again.

Setting your room temperature

Your current room temperature is shown in the display.

To set the temperature you want, just turn the dial

right to increase and left to decrease. Each ‘click’

as the dial turns represents a 0.5º change.

User Guide

Single Zone Thermostat

Y87RF

User Guide

Single Zone Thermostat

Y87RF

Night-time temperature reduction

Overnight, or if you are out, it is best to set the thermostat to

a lower temperature, as it will save you energy. In general a

reduction of 5°C is recommended, but this will depend on your

heating system and the amount of insulation in your home.

Replacing the batteries

Your batteries should be replaced

when the symbol is displayed.

To do this, separate the thermostat

from the wiring plate and insert 2

new AA alkaline batteries in place

of the empty ones. Then reattach

the thermostat to the wiring plate.

Getting to know your display

Set Temperature Indicator

Means the gure on the screen is your set temperature,

rather than your current room temerature.

Heating on

Means there is a requirement for some heating, so

your boiler should either be on or cycling on/off.

Boiler Relay Connection

Means your thermostat is successfully

connected to your Boiler Relay.

Internet Gateway Connection (optional)

Means your thermostat is successfully

connected to your Internet Gateway.

After ve seconds the current room temperature will be

displayed once again. The thermostat will then try to

maintain your set temperature as accurately as possible.

You can check your set temperature by turning the dial one ‘click’

to the left or right. The set temperature will ash up for a few

seconds, before returning to display the room temperature again.

Setting your room temperature

Your current room temperature is shown in the display.

To set the temperature you want, just turn the dial

right to increase and left to decrease. Each ‘click’

as the dial turns represents a 0.5º change.

User Guide

Single Zone Thermostat

Y87RF

User Guide

Single Zone Thermostat

Y87RF

Night-time temperature reduction

Overnight, or if you are out, it is best to set the thermostat to

a lower temperature, as it will save you energy. In general a

reduction of 5°C is recommended, but this will depend on your

heating system and the amount of insulation in your home.

Replacing the batteries

Your batteries should be replaced

when the symbol is displayed.

To do this, separate the thermostat

from the wiring plate and insert 2

new AA alkaline batteries in place

of the empty ones. Then reattach

the thermostat to the wiring plate.

Getting to know your display

Set Temperature Indicator

Means the gure on the screen is your set temperature,

rather than your current room temerature.

Heating on

Means there is a requirement for some heating, so

your boiler should either be on or cycling on/off.

Boiler Relay Connection

Means your thermostat is successfully

connected to your Boiler Relay.

Internet Gateway Connection (optional)

Means your thermostat is successfully

connected to your Internet Gateway.

After ve seconds the current room temperature will be

displayed once again. The thermostat will then try to

maintain your set temperature as accurately as possible.

You can check your set temperature by turning the dial one ‘click’

to the left or right. The set temperature will ash up for a few

seconds, before returning to display the room temperature again.

Setting your room temperature

Your current room temperature is shown in the display.

To set the temperature you want, just turn the dial

right to increase and left to decrease. Each ‘click’

as the dial turns represents a 0.5º change.

User Guide

Single Zone Thermostat

Y87RF

User Guide

Single Zone Thermostat

Y87RF

Night-time temperature reduction

Overnight, or if you are out, it is best to set the thermostat to

a lower temperature, as it will save you energy. In general a

reduction of 5°C is recommended, but this will depend on your

heating system and the amount of insulation in your home.

Replacing the batteries

Your batteries should be replaced

when the symbol is displayed.

To do this, separate the thermostat

from the wiring plate and insert 2

new AA alkaline batteries in place

of the empty ones. Then reattach

the thermostat to the wiring plate.

Getting to know your display

Set Temperature Indicator

Means the gure on the screen is your set temperature,

rather than your current room temerature.

Heating on

Means there is a requirement for some heating, so

your boiler should either be on or cycling on/off.

Boiler Relay Connection

Means your thermostat is successfully

connected to your Boiler Relay.

Internet Gateway Connection (optional)

Means your thermostat is successfully

connected to your Internet Gateway.

After ve seconds the current room temperature will be

displayed once again. The thermostat will then try to

maintain your set temperature as accurately as possible.

You can check your set temperature by turning the dial one ‘click’

to the left or right. The set temperature will ash up for a few

seconds, before returning to display the room temperature again.

Setting your room temperature

Your current room temperature is shown in the display.

To set the temperature you want, just turn the dial

right to increase and left to decrease. Each ‘click’

as the dial turns represents a 0.5º change.

User Guide

Single Zone Thermostat

Y87RF

User Guide

Single Zone Thermostat

Y87RF

Night-time temperature reduction

Overnight, or if you are out, it is best to set the thermostat to

a lower temperature, as it will save you energy. In general a

reduction of 5°C is recommended, but this will depend on your

heating system and the amount of insulation in your home.

Replacing the batteries

Your batteries should be replaced

when the symbol is displayed.

To do this, separate the thermostat

from the wiring plate and insert 2

new AA alkaline batteries in place

of the empty ones. Then reattach

the thermostat to the wiring plate.

Getting to know your display

Set Temperature Indicator

Means the gure on the screen is your set temperature,

rather than your current room temerature.

Heating on

Means there is a requirement for some heating, so

your boiler should either be on or cycling on/off.

Boiler Relay Connection

Means your thermostat is successfully

connected to your Boiler Relay.

Internet Gateway Connection (optional)

Means your thermostat is successfully

connected to your Internet Gateway.

Troubleshooting

Low batteries

If you see this battery icon then you need to

replace the batteries right away. See overleaf.

No power to the thermostat

If the thermostat screen is blank after initial installation,

then check the protective tab has been removed from

the batteries. Otherwise, try replacing the batteries.

RF communication error

If these icons are ashing, then there may be an

issue with the signal from the Boiler Relay. First

check there is mains power to the Boiler Relay. If this

does not resolve the problem, consult your installer.

Defective thermostat

If this icon is displayed then the thermostat is no

longer functioning and will need to be replaced.

4. After binding, the strength of the

signal between the devices will

appear on the thermostat for a

few seconds. 1 equals the lowest

strength and 5 the highest.

Then the normal screen will be

shown, including a symbol

to conrm the Gateway and the

thermostat are now connected.

5. Please refer to your Gateway

instructions to learn how to

create your online account and

download our smartphone app.

2. Briey touch the right-hand touch

zone once again to send the binding

signal. The and symbols will

ash until binding is successful.

3. With good reception, the

green LED on the Gateway

will then light up to conrm

successful binding.

Binding your thermostat to a

RFG100 Internet Gateway

If you want to be able to operate your Single Zone

Thermostat remotely or add scheduling then you will

need to use the Honeywell RFG100 Internet Gateway

(sold separately) and bind the thermostat to it.

To do this, please follow the full installation instructions

in the RFG100 box, and at the relevant binding stage

follow these steps to connect your thermostat:

1. Touch and hold the right-hand

touch zone for about 10 seconds

to activate the binding screen.

10s

Manufactured for and on behalf of the Environmental and

Combustion Controls Division of Honeywell Technologies

Sàrl, ACS-ECC EMEA, Z.A. La Pièce 16, 1180 Rolle,

Switzerland by its Authorised Representative Honeywell Inc.

Need help? For assistance with this product please visit:

www.honeywelluk.com

Honeywell Control Systems Ltd.

Skimped Hill Lane,

Bracknell

Berkshire

RG12 1EB

www.honeywelluk.com 50094158-006 A

Note: if you have tried to bind but have

persistent problems doing so, please

visit the URL below for assistance:

www.honeywelluk.com/support/sztbinding

Troubleshooting

Low batteries

If you see this battery icon then you need to

replace the batteries right away. See overleaf.

No power to the thermostat

If the thermostat screen is blank after initial installation,

then check the protective tab has been removed from

the batteries. Otherwise, try replacing the batteries.

RF communication error

If these icons are ashing, then there may be an

issue with the signal from the Boiler Relay. First

check there is mains power to the Boiler Relay. If this

does not resolve the problem, consult your installer.

Defective thermostat

If this icon is displayed then the thermostat is no

longer functioning and will need to be replaced.

4. After binding, the strength of the

signal between the devices will

appear on the thermostat for a

few seconds. 1 equals the lowest

strength and 5 the highest.

Then the normal screen will be

shown, including a symbol

to conrm the Gateway and the

thermostat are now connected.

5. Please refer to your Gateway

instructions to learn how to

create your online account and

download our smartphone app.

2. Briey touch the right-hand touch

zone once again to send the binding

signal. The and symbols will

ash until binding is successful.

3. With good reception, the

green LED on the Gateway

will then light up to conrm

successful binding.

Binding your thermostat to a

RFG100 Internet Gateway

If you want to be able to operate your Single Zone

Thermostat remotely or add scheduling then you will

need to use the Honeywell RFG100 Internet Gateway

(sold separately) and bind the thermostat to it.

To do this, please follow the full installation instructions

in the RFG100 box, and at the relevant binding stage

follow these steps to connect your thermostat:

1. Touch and hold the right-hand

touch zone for about 10 seconds

to activate the binding screen.

10s

Manufactured for and on behalf of the Environmental and

Combustion Controls Division of Honeywell Technologies

Sàrl, ACS-ECC EMEA, Z.A. La Pièce 16, 1180 Rolle,

Switzerland by its Authorised Representative Honeywell Inc.

Need help? For assistance with this product please visit:

www.honeywelluk.com

Honeywell Control Systems Ltd.

Skimped Hill Lane,

Bracknell

Berkshire

RG12 1EB

www.honeywelluk.com 50094158-006 A

Note: if you have tried to bind but have

persistent problems doing so, please

visit the URL below for assistance:

www.honeywelluk.com/support/sztbinding

Troubleshooting

Low batteries

If you see this battery icon then you need to

replace the batteries right away. See overleaf.

No power to the thermostat

If the thermostat screen is blank after initial installation,

then check the protective tab has been removed from

the batteries. Otherwise, try replacing the batteries.

RF communication error

If these icons are ashing, then there may be an

issue with the signal from the Boiler Relay. First

check there is mains power to the Boiler Relay. If this

does not resolve the problem, consult your installer.

Defective thermostat

If this icon is displayed then the thermostat is no

longer functioning and will need to be replaced.

4. After binding, the strength of the

signal between the devices will

appear on the thermostat for a

few seconds. 1 equals the lowest

strength and 5 the highest.

Then the normal screen will be

shown, including a symbol

to conrm the Gateway and the

thermostat are now connected.

5. Please refer to your Gateway

instructions to learn how to

create your online account and

download our smartphone app.

2. Briey touch the right-hand touch

zone once again to send the binding

signal. The and symbols will

ash until binding is successful.

3. With good reception, the

green LED on the Gateway

will then light up to conrm

successful binding.

Binding your thermostat to a

RFG100 Internet Gateway

If you want to be able to operate your Single Zone

Thermostat remotely or add scheduling then you will

need to use the Honeywell RFG100 Internet Gateway

(sold separately) and bind the thermostat to it.

To do this, please follow the full installation instructions

in the RFG100 box, and at the relevant binding stage

follow these steps to connect your thermostat:

1. Touch and hold the right-hand

touch zone for about 10 seconds

to activate the binding screen.

10s

Manufactured for and on behalf of the Environmental and

Combustion Controls Division of Honeywell Technologies

Sàrl, ACS-ECC EMEA, Z.A. La Pièce 16, 1180 Rolle,

Switzerland by its Authorised Representative Honeywell Inc.

Need help? For assistance with this product please visit:

www.honeywelluk.com

Honeywell Control Systems Ltd.

Skimped Hill Lane,

Bracknell

Berkshire

RG12 1EB

www.honeywelluk.com 50094158-006 A

Note: if you have tried to bind but have

persistent problems doing so, please

visit the URL below for assistance:

www.honeywelluk.com/support/sztbinding

Troubleshooting

Low batteries

If you see this battery icon then you need to

replace the batteries right away. See overleaf.

No power to the thermostat

If the thermostat screen is blank after initial installation,

then check the protective tab has been removed from

the batteries. Otherwise, try replacing the batteries.

RF communication error

If these icons are ashing, then there may be an

issue with the signal from the Boiler Relay. First

check there is mains power to the Boiler Relay. If this

does not resolve the problem, consult your installer.

Defective thermostat

If this icon is displayed then the thermostat is no

longer functioning and will need to be replaced.

4. After binding, the strength of the

signal between the devices will

appear on the thermostat for a

few seconds. 1 equals the lowest

strength and 5 the highest.

Then the normal screen will be

shown, including a symbol

to conrm the Gateway and the

thermostat are now connected.

5. Please refer to your Gateway

instructions to learn how to

create your online account and

download our smartphone app.

2. Briey touch the right-hand touch

zone once again to send the binding

signal. The and symbols will

ash until binding is successful.

3. With good reception, the

green LED on the Gateway

will then light up to conrm

successful binding.

Binding your thermostat to a

RFG100 Internet Gateway

If you want to be able to operate your Single Zone

Thermostat remotely or add scheduling then you will

need to use the Honeywell RFG100 Internet Gateway

(sold separately) and bind the thermostat to it.

To do this, please follow the full installation instructions

in the RFG100 box, and at the relevant binding stage

follow these steps to connect your thermostat:

1. Touch and hold the right-hand

touch zone for about 10 seconds

to activate the binding screen.

10s

Manufactured for and on behalf of the Environmental and

Combustion Controls Division of Honeywell Technologies

Sàrl, ACS-ECC EMEA, Z.A. La Pièce 16, 1180 Rolle,

Switzerland by its Authorised Representative Honeywell Inc.

Need help? For assistance with this product please visit:

www.honeywelluk.com

Honeywell Control Systems Ltd.

Skimped Hill Lane,

Bracknell

Berkshire

RG12 1EB

www.honeywelluk.com 50094158-006 A

Note: if you have tried to bind but have

persistent problems doing so, please

visit the URL below for assistance:

www.honeywelluk.com/support/sztbinding

Troubleshooting

Low batteries

If you see this battery icon then you need to

replace the batteries right away. See overleaf.

No power to the thermostat

If the thermostat screen is blank after initial installation,

then check the protective tab has been removed from

the batteries. Otherwise, try replacing the batteries.

RF communication error

If these icons are ashing, then there may be an

issue with the signal from the Boiler Relay. First

check there is mains power to the Boiler Relay. If this

does not resolve the problem, consult your installer.

Defective thermostat

If this icon is displayed then the thermostat is no

longer functioning and will need to be replaced.

4. After binding, the strength of the

signal between the devices will

appear on the thermostat for a

few seconds. 1 equals the lowest

strength and 5 the highest.

Then the normal screen will be

shown, including a symbol

to conrm the Gateway and the

thermostat are now connected.

5. Please refer to your Gateway

instructions to learn how to

create your online account and

download our smartphone app.

2. Briey touch the right-hand touch

zone once again to send the binding

signal. The and symbols will

ash until binding is successful.

3. With good reception, the

green LED on the Gateway

will then light up to conrm

successful binding.

Binding your thermostat to a

RFG100 Internet Gateway

If you want to be able to operate your Single Zone

Thermostat remotely or add scheduling then you will

need to use the Honeywell RFG100 Internet Gateway

(sold separately) and bind the thermostat to it.

To do this, please follow the full installation instructions

in the RFG100 box, and at the relevant binding stage

follow these steps to connect your thermostat:

1. Touch and hold the right-hand

touch zone for about 10 seconds

to activate the binding screen.

10s

Manufactured for and on behalf of the Environmental and

Combustion Controls Division of Honeywell Technologies

Sàrl, ACS-ECC EMEA, Z.A. La Pièce 16, 1180 Rolle,

Switzerland by its Authorised Representative Honeywell Inc.

Need help? For assistance with this product please visit:

www.honeywelluk.com

Honeywell Control Systems Ltd.

Skimped Hill Lane,

Bracknell

Berkshire

RG12 1EB

www.honeywelluk.com 50094158-006 A

Note: if you have tried to bind but have

persistent problems doing so, please

visit the URL below for assistance:

www.honeywelluk.com/support/sztbinding

Other manuals for Y87RF

Table of contents

Other Honeywell Thermostat manuals

Honeywell

Honeywell PRO TH2000 Series User manual

Honeywell

Honeywell TRADELINE Q7100A User manual

Honeywell

Honeywell RTH6300 User manual

Honeywell

Honeywell TH3110D1008 - Digital Thermostat, 1h User manual

Honeywell

Honeywell Tradeline T874A-F User manual

Honeywell

Honeywell Lyric User manual

Honeywell

Honeywell T8000 Manual

Honeywell

Honeywell RCT8100 User manual

Honeywell

Honeywell TRADELINE Q7300H Series User guide

Honeywell

Honeywell RTH2310 User manual

Honeywell

Honeywell YRTH7500D1009 - 5 Day Program Thermostat User manual

Honeywell

Honeywell VisionPRO Series User manual

Honeywell

Honeywell FocusPRO Wi-Fi TH6000 Series User manual

Honeywell

Honeywell FocusPRO Wi-Fi TH6000 Series User manual

Honeywell

Honeywell RTH7400 series User manual

Honeywell

Honeywell CM67 User manual

Honeywell

Honeywell Tradeline T8024D Operation manual

Honeywell

Honeywell RTH111 series User manual

Honeywell

Honeywell TB7220 COMMERCIALPRO Operation manual

Honeywell

Honeywell T822K User manual

Honeywell

Honeywell CT31 User manual

Honeywell

Honeywell RTH7400 series User manual

Honeywell

Honeywell VisionPRO Series User manual

Honeywell

Honeywell Chronotherm IV T8611G User manual

Popular Thermostat manuals by other brands

EWELLY

EWELLY EW-181 manual

Prolon

Prolon T1100 Hardware guide

Computherm

Computherm Q20 operating instructions

Heatmiser

Heatmiser neoStat user manual

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA user manual

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat user manual

Saswell

Saswell SAS920XWHB-7-S-RF User manual and warranty card

Aircalo

Aircalo TFP1-ET85P2 operating manual

Carrier

Carrier DEBONAIR 33CS Installation and operating instructions

Lennox

Lennox iHarmony Zone Thermostat Installation and setup guide

Gemtech

Gemtech GT7000 Operation

Rollei

Rollei Smartes 45000 manual

Sinope

Sinope TH1300RF user guide

NuTone

NuTone NTBZ48 Installation & operation guide

Stelpro

Stelpro MAESTRO ASMT402AD user guide

Aube Technologies

Aube Technologies TH305 owner's guide

Powtier Controls

Powtier Controls 505MST instruction manual

Kanmor

Kanmor Zone Control 369e manual