Honeywell FocusPRO TH5220D User manual
TH5220D
Non-programmable Digital Thermostat
Installation
Guide
Product Application
This thermostat provides electronic control of 24 VAC single-stage and multi-stage
heating and cooling systems, or 750 mV heating systems.
System Types
(up to 2 heat/2 cool)
• Gas, oil, or electric heat with air
conditioning
• Warm air, hot water, high-efficiency
furnaces, heat pumps, steam, gravity
• Heat only — two-wire systems,
power to open and close zone
valves (Series 20), and normally-
open zone valves
• Heat only with fan
• Cool only
• 750 mV heating systems
Power Options
• Battery power only
• Common wire only
• Common wire with battery backup
Changeover Options
• Selectable manual or
auto-changeover modes
System Settings
• Heat, Off, Cool,Auto, Em Heat
Fan Settings
• Auto, On
Must be installed by a trained, experienced technician
• Read these instructions carefully. Failure to follow these instructions can
damage the product or cause a hazardous condition.
• Check the ratings in this booklet to verify that this product is suitable for your
application (see page 17).
• Always test for proper operation after installation (see page 13).
CAUTION: ELECTRICAL HAZARD
Can cause electrical shock or equipment damage. Disconnect power before
beginning installation.
MERCURY NOTICE
If this product is replacing a control that contains mercury in a sealed tube, do not
place the old control in the trash. Contact your local waste management authority for
instructions regarding recycling and proper disposal.
® U.S. Registered Trademark. Patents pending.
Copyright © 2005 Honeywell International Inc. All rights reserved.
1
Install the thermostat about 5 feet (1.5m) above the floor in an area
with good air circulation at average temperature.
Do not install in locations where the thermostat can be affected by:
• Drafts or dead spots behind doors and in corners
• Hot or cold air from ducts
• Sunlight or radiant heat from appliances
• Concealed pipes or chimneys
• Unheated/uncooled areas such as an outside wall behind the thermostat
NO
NO NO
IInnssttaallllaattiioonn
Pre-installation checklist ................2
Wallplate installation ......................3
Wiring..............................................4
Wiring diagrams ..............................5
Power options ..............................10
Thermostat mounting ..................10
SSeettuuppaannddtteessttiinngg
Installer setup................................11
Installer system test ......................13
Explanation of features ................14
AAppppeennddiicceess
Quick reference to controls..........15
Quick reference to display............15
Battery replacement......................15
In case of difficulty ......................16
Accessories/replacement parts ....17
Specifications ................................17
Table of contents
Installation tips
Installation Guide
2
Pre-installation checklist
Package contents
Check to make sure your package includes the following items:
Operating manual
Wall anchors and
mounting screws
(2 each)
AA alkaline
batteries (2)
FocusPRO™TH5220D
digital thermostat
(wallplate attached to back)
Required tools & supplies
• No. 2 Phillips screwdriver
• Small pocket screwdriver
• Drill
• Drill bit (3/16” for drywall, 7/32” for plaster)
• Hammer
• Pencil
• Electrical tape
• Level (optional)
FocusPRO™TH5220D Non-programmable Digital Thermostat
3
Remove the wallplate from the ther-
mostat as shown at left, then follow
directions below for mounting.
1 Pull wires through wire hole.
2 Position wallplate on wall, level and
mark hole positions with pencil.
3 Drill holes at marked positions as
shown below, then tap in supplied
wall anchors.
4 Place wallplate over anchors, insert
and tighten mounting screws.
Insert finger into wire hole and pull to
remove wallplate from thermostat.
Drill 3/16” holes for drywall.
Drill 7/32” holes for plaster.
Wall anchors
Mounting screwsWire hole
Wallplate installation
Installation Guide
4
Wiring
1 Loosen screw terminals, insert
wires into terminal block, then
re-tighten screws.
2 Push excess wire back into the
wall opening. Keep wires in shaded
area as shown at left.
3 Plug the wall opening with non-
flammable insulation to prevent
drafts from affecting thermostat
operation.
Conventional
Heat Pump
NOTES
R & Rc terminals
In single-transformer system, leave metal
jumper in place between R & Rc. Remove
metal jumper if two-transformer system.
C terminal
The C (common wire) terminal is optional
when thermostat is powered by batteries.
W (O/B) terminal
If thermostat is configured for a heat pump
in the Installer Setup, configure changeover
valve for cool (“O” factory setting) or heat
(“B”).
L terminal (Output)
Heat pump reset. L terminal powered contin-
uously when thermostat is set to Em Heat.
Configure thermostat for 2 heat / 1 cool heat
pump in the Installer Setup.
Wire specifications
Use 18- to 22-gauge thermostat wire.
Shielded cable is not required.
Keep wires in this
shaded area
CAUTION: ELECTRICAL HAZARD. Can cause electrical shock or equipment damage.
Disconnect power before wiring.
Wiring
Terminal Designations
Conventional Terminal Letters:
Y2 2nd stage compressor contactor
W2 2nd stage heat relay
GFan relay
W1st stage heat relay
CCommon wire from secondary side of
cooling system transformer
Y1st stage compressor contactor
RHeating power. Connect to secondary
side of heating system transformer.
Rc Cooling power. Connect to secondary
side of cooling system transformer.
Heat Pump Terminal Letters:
LHeat pump reset. L terminal powered
continuously when System is set to Em
Heat.
EEmergency heat relay
Aux Auxiliary heat relay
GFan relay
O/B Changeover valve for heat pumps
CCommon wire from secondary side of
cooling system transformer.
YCompressor contactor
RHeating power. Connect to secondary
side of heating system transformer.
Rc Cooling power. Connect to secondary
side of cooling system transformer.
FocusPRO™TH5220D Non-programmable Digital Thermostat
5
Typical 1H/1C system: 1 transformer Typical 1H/1C system: 2 transformers
Remove
jumper
Wiring diagrams
Power supply. Provide disconnect means and overload protection as required.
Factory-installed jumper. Remove for 2-transformer systems only.
Optional 24VAC common connection.
In Installer Setup, set system type to Heat Only.
In Installer Setup, set system type to 1Heat/1Cool Heat Pump & changeover valve to 0or B.
In Installer Setup, set system type to 2Heat/1Cool Heat Pump.
L terminal is powered continuously when thermostat is set to Em Heat.
Install field jumper between Aux and E if there is no emergency heat relay.
In Installer Setup, set system type to 2Heat/2Cool conventional.
Installation Guide
6
Wiring diagrams
Typical 1H/1C heat pump system Typical heat-only system
Power supply. Provide disconnect means and overload protection as required.
Factory-installed jumper. Remove for 2-transformer systems only.
Optional 24VAC common connection.
In Installer Setup, set system type to Heat Only.
In Installer Setup, set system type to 1Heat/1Cool Heat Pump & changeover valve to 0or B.
In Installer Setup, set system type to 2Heat/1Cool Heat Pump.
L terminal is powered continuously when thermostat is set to Em Heat.
Install field jumper between Aux and E if there is no emergency heat relay.
In Installer Setup, set system type to 2Heat/2Cool conventional.
FocusPRO™TH5220D Non-programmable Digital Thermostat
7
Typical heat-only system with fan Heat-only system (Series 20)
Wiring diagrams
Power supply. Provide disconnect means and overload protection as required.
Factory-installed jumper. Remove for 2-transformer systems only.
Optional 24VAC common connection.
In Installer Setup, set system type to Heat Only.
In Installer Setup, set system type to 1Heat/1Cool Heat Pump & changeover valve to 0or B.
In Installer Setup, set system type to 2Heat/1Cool Heat Pump.
L terminal is powered continuously when thermostat is set to Em Heat.
Install field jumper between Aux and E if there is no emergency heat relay.
In Installer Setup, set system type to 2Heat/2Cool conventional.
Installation Guide
8
Typical cool-only system Heat-only system (normally open zone valve)
Wiring diagrams
Power supply. Provide disconnect means and overload protection as required.
Factory-installed jumper. Remove for 2-transformer systems only.
Optional 24VAC common connection.
In Installer Setup, set system type to Heat Only.
In Installer Setup, set system type to 1Heat/1Cool Heat Pump & changeover valve to 0or B.
In Installer Setup, set system type to 2Heat/1Cool Heat Pump.
L terminal is powered continuously when thermostat is set to Em Heat.
Install field jumper between Aux and E if there is no emergency heat relay.
In Installer Setup, set system type to 2Heat/2Cool conventional.
Other manuals for FocusPRO TH5220D
1
Table of contents
Other Honeywell Thermostat manuals
Honeywell
Honeywell DT90E User manual
Honeywell
Honeywell Lyric T6 Pro Wi-Fi User manual
Honeywell
Honeywell TRADELINE T8400C User manual
Honeywell
Honeywell VisionPRO 8000 User manual
Honeywell
Honeywell TB7100A1000 - MultiPro Commercial Thermostat User manual
Honeywell
Honeywell VisionPRO 8000 Series User manual
Honeywell
Honeywell RTH9580 Wi-Fi User manual
Honeywell
Honeywell PRO 1000 User manual
Honeywell
Honeywell RTHL221 series User manual
Honeywell
Honeywell TL8100 User manual
Honeywell
Honeywell CT1501 User manual
Honeywell
Honeywell RTH221 Series User manual
Honeywell
Honeywell FEMA TAM Series User manual
Honeywell
Honeywell TROL-A-TEMP Q674B User manual
Honeywell
Honeywell RTHL2510 series User manual
Honeywell
Honeywell RTHL2310 series User manual
Honeywell
Honeywell L641AI039 Operation manual
Honeywell
Honeywell THE DIGITAL ROUND CT8775A User manual
Honeywell
Honeywell Super Tradeline Q674L User manual
Honeywell
Honeywell RTH111 series User manual
Popular Thermostat manuals by other brands
Saswell
Saswell SAS920XWHB-7-S-RF User manual and warranty card
Aircalo
Aircalo TFP1-ET85P2 operating manual
Carrier
Carrier DEBONAIR 33CS Installation and operating instructions
Lennox
Lennox iHarmony Zone Thermostat Installation and setup guide
Gemtech
Gemtech GT7000 Operation
Rollei
Rollei Smartes 45000 manual
