Honeywell C7189R User manual
Installation
Guide
69-2459EFS-03
C7189R
Wireless Indoor Sensor
Capteur d’intérieur sans fil
Sensor inalámbrico para interiores
69-2459EFS_B.indd 1 7/13/2011 1:30:19 PM
Installation Guide
ii
69-2459EFS—03
® U.S. Registered Trademark.
Copyright © 2011 Honeywell International Inc.
All rights reserved.
About your wireless indoor sensor
This sensor monitors temperature and humidity in any indoor location and transmits it
wirelessly to the thermostat.
You can set the system to monitor temperature at the thermostat, or at the sensor location,
or use an average of both to optimize comfort throughout the home. The thermostat can
accommodate and average temperature readings from as many as 6 sensors.
When multiple sensors are installed, the thermostat can monitor temperature and humidity
in separate locations, and you can set it to use different readings from different sensors.
For example, one sensor can control humidication on the main level, while another controls
dehumidication in a crawl space. For more information, see the instructions provided with
the thermostat.
Operating Ambient Temperature: 0 to 120° F (-17.8 to 48.9° C)
For Optimal Battery Life: 35 to 114° F (1.7 to 45.6° C)
The thermostat will display a warning to replace batteries in the indoor sensor about 2 months
before power is depleted. The sensor status light will begin flashing red about 3 weeks before
power is depleted. During normal operation, the status light remains off.
69-2459EFS_B.indd 2 7/13/2011 1:30:19 PM
Wireless Indoor Sensor
169-2459EFS—03
MCR32933
MCR32934 MCR32935
Install 2 fresh AAA alkaline batteries.
Status light will briefly flash green. If it
flashes red, batteries are not good.
Install batteries and link sensor to thermostat
1
Install batteries, then enter Wireless Setup mode at the thermostat. Press and
release the CONNECT button to link the wireless sensor to the thermostat.
Press and release CONNECT.
After a short delay, the status light
will glow green for 15 seconds.
If the status light is red, the
sensor did not link with the
thermostat. See Note.
Verify the thermostat is in the Wireless Setup
mode and the indoor sensor is at least 2 feet
away from the EIM or thermostat.
69-2459EFS_B.indd 1 7/13/2011 1:30:20 PM
Installation Guide
2
69-2459EFS—03
M32936
Mount sensor in suitable location
2
Install sensor on an interior wall, about 4 to 6 feet above the floor. To ensure
accurate temperature readings, choose a location away from air vents and not
exposed to direct sunlight.
1 Remove the wallplate and mount
it 4 to 6 feet above the floor on an
interior wall. Drill 3/16-inch holes
for drywall, 7/32-inch for plaster.
2 Attach sensor securely to wallplate
as shown.
If you replace a thermostat or Equipment Interface Module: You must disconnect the indoor
sensor from the old device. To disconnect, press and hold the CONNECT button on the indoor
sensor until the status light glows amber (hold for about 10 seconds). Then follow the steps on page
1 to re-link the indoor sensor to the wireless network.
69-2459EFS_B.indd 2 7/13/2011 1:30:20 PM
Wireless Indoor Sensor
369-2459EFS—03
5-year limited warranty
Honeywell warrants this product, excluding battery, to be
free from defects in the workmanship or materials, under
normal use and service, for a period of five (5) years from
the date of purchase by the consumer. If at any time during
the warranty period the product is determined to be defec-
tive or malfunctions, Honeywell shall repair or replace it (at
Honeywell’s option).
If the product is defective,
(i) return it, with a bill of sale or other dated proof of pur-
chase, to the place from which you purchased it; or
(ii) call Honeywell Customer Care at 1-800-468-1502.
Customer Care will make the determination whether the
product should be returned to the following address:
Honeywell Return Goods, Dock 4 MN10-3860, 1885
Douglas Dr. N., Golden Valley, MN 55422, or whether a
replacement product can be sent to you.
This warranty does not cover removal or reinstallation
costs. This warranty shall not apply if it is shown by
Honeywell that the defect or malfunction was caused by
damage which occurred while the product was in the pos-
session of a consumer.
Honeywell’s sole responsibility shall be to repair or replace
the product within the terms stated above. HONEYWELL
SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE
OF ANY KIND, INCLUDING ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES RESULTING, DIRECTLY OR
INDIRECTLY, FROM ANY BREACH OF ANY WARRANTY,
EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF THIS
PRODUCT. Some states do not allow the exclusion or
limitation of incidental or consequential damages, so this
limitation may not apply to you.
THIS WARRANTY IS THE ONLY EXPRESS WARRANTY
HONEYWELL MAKES ON THIS PRODUCT. THE DURATION
OF ANY IMPLIED WARRANTIES, INCLUDING THE
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE, IS HEREBY LIMITED TO THE
FIVE-YEAR DURATION OF THIS WARRANTY. Some states
do not allow limitations on how long an implied warranty
lasts, so the above limitation may not apply to you.
This warranty gives you specific legal rights, and you may
have other rights which vary from state to state.
If you have any questions concerning this warranty, please
write Honeywell Customer Care, 1985 Douglas Dr, Golden
Valley, MN 55422 or call 1-800-468-1502.
69-2459EFS_B.indd 3 7/13/2011 1:30:20 PM
Installation Guide
4
69-2459EFS—03
Regulatory information
FCC Compliance Statement (Part 15.19) (USA only)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired
operation.
FCC Warning (Part 15.21) (USA only)
Changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
FCC Interference Statement (Part 15.105 (b)) (USA only)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
69-2459EFS_B.indd 4 7/13/2011 1:30:21 PM
Wireless Indoor Sensor
569-2459EFS—03
Regulatory information
Equipment interface module, thermostats and indoor sensor
To comply with FCC and Industry Canada RF exposure limits for general population/ uncontrolled
exposure, the antenna(s) used for these transmitters must be installed to provide a separation distance
of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other
antenna or transmitter.
Section 7.1.2 of RSS-GEN
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of type
and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential
radio interference to other users, the antenna type and its gain should be so chosen that the equivalent
isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
Section 7.1.3 of RSS-GEN
Operation is subject to the following two conditions:
1. this device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation
of the device.
69-2459EFS_B.indd 5 7/13/2011 1:30:21 PM
i
69-2459EFS—03
Guide d’installation
À propos du capteur d’intérieur sans fil
® U.S.Marque déposée américaine.
Copyright © 2011 Honeywell International Inc.
Tous droits réservés.
Ce capteur contrôle la température et l’humidité dans tout espace intérieur et la transmet
sans l au thermostat.
Le système peut être réglé pour contrôler la température au thermostat ou à l’emplacement
du capteur, ou pour utiliser une moyenne des deux pour maximiser le confort dans toute
la maison. Le thermostat peut recevoir et faire la moyenne de relevés de température
provenant d’un maximum de 6 capteurs.
Lorsque plusieurs capteurs sont installés, le thermostat peut contrôler la température et
l’humidité dans des endroits différents, et il est possible de le régler pour qu’il utilise des
relevés différents provenant de plusieurs capteurs. Par exemple, un capteur peut contrôler
l’humidication à l’étage principal, tandis qu’un autre peut contrôler la déshumidication
dans un vide sanitaire. Pour plus d’informations, consulter les instructions fournies avec le
thermostat.
Le thermostat affiche un avertissement indiquant de remplacer les piles dans le capteur d’intérieur environ
2 mois avant qu’elles ne soient complètement déchargées. Le voyant de statut du capteur commence
à clignoter en rouge environ 3 semaines avant que la charge soit complètement épuisée. Durant le
fonctionnement normal, le voyant de statut est éteint.
Température ambiante de service : -17,8 à 48,9 °C (0 à 120 °F)
Pour une durée optimale de la pile : 1,7 à 45,6 °C (35 à 114 °F)
69-2459EFS_B.indd 1 7/13/2011 1:30:21 PM
Capteur d’intérieur sans fil
169-2459EFS—03
MCR32933
MCR32934 MCR32935
Installation des piles et connexion du capteur au thermostat
1
Insérer 2 piles alcalines AAA neuves.
Le voyant de statut clignote brièvement
en vert. S’il clignote en rouge, les piles
sont usées.
Installer les piles et mettre le thermostat en mode de configuration sans fil.
Appuyer sur le bouton CONNECT (Connexion) puis le relâcher pour connecter le
capteur sans fil au thermostat.
Appuyer sur le bouton CONNECT
(Connexion) et le relâcher. Après
un court délai, le voyant de statut
s’allume en vert pendant 15
secondes.
Si le voyant de statut est rouge,
le capteur n’est pas connecté au
thermostat. Voir la remarque.
Vérifier que le thermostat est en mode
de configuration sans fil et que le capteur
intérieur est situé à au moins 61 cm (2 pi)
du module d’interface d’équipement ou du
thermostat.
69-2459EFS_B.indd 1 7/13/2011 1:30:21 PM
2
69-2459EFS—03
Guide d’installation
Installation du capteur dans un endroit approprié
2
Installer le capteur sur un mur intérieur entre 1,2 et 1,8 m (4 et 6 pi) au-dessus
du sol. Pour assurer des relevés de température précis, choisir un emplacement
éloigné de conduites d’air et non exposé aux rayons directs du soleil.
1 Retirer la plaque murale et la
monter de 1,2 à 1,8 m (4 à 6 pi)
au-dessus du sol sur un mur
intérieur. Percer des trous de 3/16
po sur les cloisons sèches ou des
trous de 7/32 po pour le plâtre.
2 Bien attacher le capteur à la plaque
murale comme illustré.
En cas de remplacement d’un thermostat ou d’un module d’interface d’équipement : Le
capteur d’intérieur doit être débranché de l’ancien appareil. Pour débrancher, appuyer (pendant
environ 10 secondes) sur le bouton CONNECT (Connexion) du capteur d’intérieur jusqu’à ce que le
voyant de statut orange clignote. Suivre ensuite les étapes indiquées à la page 1 pour reconnecter
le capteur d’intérieur au réseau sans fil.
M32936
69-2459EFS_B.indd 2 7/13/2011 1:30:21 PM
Table of contents
Languages:
Other Honeywell Temperature Controllers manuals
Honeywell
Honeywell T7560A User manual
Honeywell
Honeywell Enraf VITO User manual
Honeywell
Honeywell VISIONPRO 69-1815EFS-06 User manual
Honeywell
Honeywell SDC heating and district heating controller User manual
Honeywell
Honeywell ASC02-01WM User manual
Honeywell
Honeywell ICON-343C User manual
Honeywell
Honeywell C7189A User manual
Honeywell
Honeywell T7470A1009 Instruction manual
Honeywell
Honeywell T7460H User manual
Honeywell
Honeywell ADEMCO 5821 Assembly instructions
Honeywell
Honeywell ST9400S User manual
Honeywell
Honeywell TS13C User manual
Honeywell
Honeywell C7089 User manual
Honeywell
Honeywell TS33F User manual
Honeywell
Honeywell ST9400C User manual
Honeywell
Honeywell C7189U User manual
Honeywell
Honeywell H7625A User manual
Honeywell
Honeywell TS13F User manual
Honeywell
Honeywell Heating Controller SDC User manual
Honeywell
Honeywell Farenhyt Series User manual
Popular Temperature Controllers manuals by other brands
SMC Networks
SMC Networks Thermo-con INR-244-639 Operation manual
eltherm
eltherm Ex-TC It Series operating instructions
Omron
Omron C200H-TV Series Operation manual
industrie technik
industrie technik CA1 instructions
KRAL
KRAL EET 32 operating instructions
dixell
dixell XR420C Installing and operating instructions