Honeywell LYNXDM-GSM Assembly instructions

K14515V1 8/07 Rev. A

LYNXDM-GSM/LYNXDM-IGSM

COMMUNICATIONS MODULES

INSTALLATION AND SETUP GUIDE

SYSTEM OVERVIEW

Introduction

The LYNXDM-GSM and LYNXDM-IGSM are desk or wall mounted communications modules for the LYNXR-I

Series control panel. Each module is equipped with an integral AlarmNet 7845GSM Digital Cellular or 7845-

iGSM Internet Communication Module with Remote Services. It represents the latest and most innovative

communication technology for the security industry and uses the most sophisticated encryption to ensure the

highest level of security for your customer.

The LYNXDM-GSM and LYNXDM-IGSM modules require an AlarmNet–i account. For new installations,

please obtain the account information from the central station prior to programming this module.

General Information

LYNXDM-GSM

Honeywell's LYNXDM-GSM cellular communication module transmits signals via the AlarmNet-G network

(GSM cellular network), using GPRS and forwards them to your Central Station. If the GPRS network is

unavailable, the LYNXDM-GSM (if enabled by the dealer) will attempt to send the transmission via SMS

(Short Message Service and/or e-mail).

LYNXDM-IGSM

Honeywell’s LYNXDM-IGSM Internet communication module communicates from your customer’s network

connection to the Honeywell NOC via the AlarmNet-I network. The NOC receives data and routes the

information to the Central Station of your choice, based on the account number you assign to the module. The

same account number is used for both Internet and GSM transmissions. If, for some reason, Internet

connectivity is not available (for example, your customer’s ISP is off line or disconnected), the LYNXDM-IGSM

will transmit signals via the AlarmNet-G (GSM) cellular network, using GPRS. These transmissions are sent to

the Honeywell NOC and then forwarded to your Central Station exactly the same way as if they were received

via the Internet.

If the Internet AND GPRS are both unavailable, the LYNXDM-IGSM will attempt to send the transmission via

SMS, also known as a text message. If all three methods fail, the module will attempt to deliver the alarm until

the alarm time expires. Once the old alarm time has expired, the alarm is dead and will not be delivered.

About AlarmNet-I Internet Application

AlarmNet-I is a fully encrypted, secure method of delivering alarm messages from a protected premise to an

AlarmNet equipped central station. An Internet Communicator Module transmits status, supervisory, and

alarm messages to the AlarmNet Control Center using a broadband Internet connection. The AlarmNet Control

Center identifies, validates, and forwards the messages to the appropriate AlarmNet central station.

Encryption

The LYNXDM-IGSM supports private key encryption. Private key encryption means that both the sender and

the receiver know the KEY used to encrypt the data. Each device produced by Honeywell is loaded with a

globally unique identifier called a MAC number, and a large random number or KEY. This KEY and MAC

number are also stored in the AlarmNet servers. When a device contacts AlarmNet, it sends the MAC number

in the clear followed by the message that is encrypted using the KEY data. The server looks up its copy of the

KEY based on the MAC number and uses that KEY to decrypt the message.

The LYNXDM-IGSM uses 256 bit AES (Rijndael) encryption (which is required for certain government

installations). The AlarmNet-I AES Encryption Software Module Version 1.0 contained in the Honeywell

products has NIST approval. Listings for this approval can be found at

http://csrc.nist.gov/cryptval/aes/aesval.html Certification number 127.

- 2 -

System Features

Feature LYNXDM-GSM LYNXDM-IGSM

•Quick connection to compatible LYNXR-I series control panels x x

•Simple programming using a 7720P programming tool x x

•Reports fire, burglary, and status messages via wireless network x x*

•Reports fire, burglary, and status messages via internet x

•Allows uploading and downloading of control panel data via the wireless

network. X x*

•Allows uploading and downloading of control panel data via internet. X

•Provides 2-way communication with the control using ECP messaging x x

•Sends reports in Contact ID format x x

•Supports two hardwire zone trigger inputs (zones 6 and 7) x x

•Easy CAT-5 10 BaseT connection to a hub or router x

•Installs behind firewalls without compromising network security x

•Supports dynamic or static IP addressing x

•Supports remote control of alarm system via Remote Services Feature x x

* As a backup to the internet.

The LYNXDM-GSM and LYNXDM-IGSM provide the following types of supervision and module fault detection:

•Network communication failure: In the event the AlarmNet network does not hear a supervisory message

from the module within a specified time (“Supervision” option, 24 hours, 30 days, or none), AlarmNet

notifies the central station of a communication failure.

•Communication path failure: In the event the module detects a communication path failure, the control

panel can be notified of a trouble condition with the module after a specified time has elapsed.

Remote Services Features

The Remote Services Features can only be used with LYNXR-I Series controls Revision 16 or later. Multi

Mode (E-mail notification) is intended as a convenience for the user, and does not replace Central Station

reporting of critical events (alarms, troubles, etc.).

Remote Services allow the end user to communicate with their Security System remotely via several features.

Availability of this service is controlled by the dealer via the web-based programming tool on the AlarmNet

Direct website. Once enabled, the specific programming fields associated with these features can be

programmed either remotely using the AlarmNet Direct website or locally using the 7720P Programming Tool.

These new web services will allow users to:

•Receive e-mail and text message notification of system events (Multi-Mode feature)

•Access their security system from a computer via a website (Remote Access feature)

•Perform system functions and receive confirmations using text messages (SMS feature)

INSTALLATION

The incoming wiring can be routed through the opening in the rear of the back plate or through the wire

troughs in the mount’s case back. A wire knockout is also provided in the desk mount front case.

Installing the desk mount

1. Route the incoming power, telephone and/or internet wiring through the appropriate openings in the

mount’s rear case.

2. Route incoming power, telephone and communications, etc. wiring through the mount’s front case.

3. Proceed to Wiring the LYNXR-I or LYNXR-ISIA section.

Installing the wall mount

1. Locate the rear case over the mounting surface such that the opening in the case is aligned with the

wire/cable access opening (in the mounting surface).

If the wiring will be run externally, it should be routed through the wire troughs in the wall mount case back.

- 3 -

2. Route the incoming power, telephone and/or internet wiring through the appropriate openings in the

mount’s rear case.

3. Mount the rear case to a sturdy wall using the four screws (supplied).

4. Route incoming power, telephone and communications, etc. wiring through the mount’s front case.

5. Proceed to Wiring the LYNXR-I or LYNXR-ISIA section.

MOUNT

(REAR CASE)

09004-005-V0

FOR EXTERNAL ANTENNA

50 OHM, MMCX ONLY

Honeywell

GSM

GPPS

WEB

MODE2

MODE1

RSSI

7720PPROGRAMMERPORTNOT

FORTELEPHONESERVICEUSE!

PRIMARYPOWER:9 -16.5VAC

CURRENT:900mAPEAK,70mASTANDBY

BATTERY:8V.3.1 AHrFOR24HrBACKUP

FCC:XXXXXXXXXXIC:YYYYYYYYYY

ARMEDREADY

RECORD VOLUMEPLAY

LIGHTS ON TEST BYPASS

LIGHTS OFF CODE CHIME

STATUSNO DELAYFUNCTION

ESCAPE

DELETE

ADD

SELECT

AUX

789

STAY

123

456

OFF

DESK MOUNT

(FRONT CASE)

WALL MOUNT

(FRONT CASE)

LYNXR-I / LYNXR-ISIA

Figure 1 - LYNXDM-GSM/LYNXDM-IGSM Desk/Wall Mount Installation

Wiring the LYNXR-I or LYNXR-ISIA

1. Release the LYNXR-I front case assembly from the rear case by depressing the two locking tabs at the top

of the unit with the blade of a medium size screwdriver (refer to Figure 2).

2. Once these tabs have been released, insert the screwdriver in the side of the case and release the side

locking tabs by gently twisting.

DO NOT disconnect the ribbon cable from the terminal strip board. Disconnect the cable only from the front

assembly board.

3. Carefully disconnect the ribbon cable from the front assembly, leaving the ribbon cable connected to

the terminal block PC board (refer to Figure 2). The rear case contains the terminal block for making

wiring connections.

When installing the 4-wire communication cable, you may find it easier to make the connection at the LYNXR-I

first. The cable can then be routed through the mount’s front case.

4. Feed the 4-wire communication cable from the LYNXR-I rear case through the mount’s front case.

5. Feed the incoming wiring from the wall or desk mount rear case through the mount’s front case and into

the LYNXR-I rear case.

6. Slide the LYNXR-I onto the wall or desk mount front case locking tabs.

Step 7 only applies to wall mount installations.

7. Once the wires have been routed, the assembled wall mount front case and LYNXR-I rear case can be

hung from the wall mount rear case using three hooks on the inside of the wall mount front case and three

tabs on lower part of the wall mount’s rear case (refer to Figure 3).

- 4 -

8. Connect the 4-wire communication cable connector to the LRR/IP communications port on the LYNXR-I

(refer to figure 4).

9. Make the wiring connections to the LYNXR-I in accordance with the LYNXR-I or LYNXR-ISIA

Installation Instructions.

10. Route the wires as shown in Figure 4.

LOCKING

TABS

LOCKING

TABS

LOCKING TABS

RED WIRE

MARKING

DISCONNECT

THIS END ONLY!

07000-003-V1

Figure 2 – LYNXR-I Series Control

09004-013-V0

WALL MOUNT

FRONT CASE AND

LYNXR-I REAR CASE

WALL MOUNT

REAR CASE

HOOKS

TABS

TURN OVER

FOR EXTERNAL ANTENNAFOR EXTERNAL ANTENNA

50 OHM, MMCX ONLY50 OHM, MMCX ONLY

7720PPROGRAMMERPORTNOT

7720P PROGRAMMER PORT NOT

FORTELEPHONESERVICEUSE!

FOR TELEPHONE SERVICE USE!

PRIMARYPOWER: 9 - 16.5 VAC

PRIMARY POWER: 9 - 16.5 VAC

CURRENT: 900mAPEAK, 70mASTANDBY

CURRENT: 900mA PEAK, 70mA STANDBY

BATTERY:8V. 3.1 AHrFOR24HrBACKUP

BATTERY: 8V. 3.1 AHr FOR 24 Hr BACKUP

FCC:XXXXXXXXXXIC: YYYYYYYYYY

FCC:XXXXXXXXXX IC: YYYYYYYYYY

Figure 3 – LYNXDM-GSM/LYNXDM-IGSM Assembly

- 5 -

FOR 7720P

FOR EXTERNAL ANTENNA

50 OHM, MMCX ONLY

7720P PROGRAMMER PORT NOT

FOR TELEPHONE SERVICE USE!

PRIMARY POWER: 9 - 16.5 VAC

CURRENT: 900mA PEAK, 70mA STANDBY

BATTERY: 8V. 3.1 AHr FOR 24 Hr BACKUP

FCC:XXXXXXXXXX IC: YYYYYYYYYY

09004-010-V0

7651312 1514 161110984321

7651110984321

MODE AND STATUS

INDICATOR SWITCH

LRR/IP

COMMUNICATION PORT

RIBBON

CABLE

INCOMING

POWER,

TELEPHONE

& INTERNET

LINES

WIRE TIE LOOP

TAMPER

SWITCH

BATTERY PACK

INTERNET

CONNECTION

(LYNXDM-IGSM ONLY)

4-WIRE

COMMUNICATIONS

CABLE

WIRE TIE

LOOPS

TB 1

NETWORK

CONNECTIVITY

LED DISPLAY

(LYNXDM-IGSM ONLY)

Figure 4 - LYNXDM-GSM/LYNXDM-IGSM Wire Routing

Wiring the LYNXDM-GSM/LYNXDM-IGSM

1. Install a jumper wire between terminals 2 and 3 on the communication modules’s terminal strip.

2. Connect the 4-wire communication cable to the communication module’s terminal strip (refer to Figure 5).

3. If you are installing a LYNXDM-IGSM, connect the incoming cable/DSL connector to the receptacle on the

communication module.

4. Secure the wiring to the built-in wire loops using tie wraps, as required.

5. After the wiring connections are complete, carefully reconnect the ribbon cable to the LYNXR-I front case

circuit board connector (properly aligning the red wire).

6. Snap the assembled LYNXR-I and the wall or desk mount front case to the mount’s back case so it is

secured by the locking tabs.

- 6 -

7845GSM

LYNX

SUPER HIGH

CAPACITY

BATTERY

(OPTIONAL)

REQUIRED FOR

24-HR BACKUP

7845GSM-028-V0

GND

Z3 OR DATA OUT

Z1/Z2 OR DATA IN

ECP (+) VOLTAGE INPUT

RED

BLK

GRN

YEL

RED

BLK

GRN

YEL

4-WIRE CABLE (N4632-4)

TB1

LRR/IP COMMUNICATIONS PORT

LYNXR-I CONTROL PANEL

+12 VDC

GND

D ATA I N

DATA OUT

LYNX

STANDARD

CAPACITY

BATTERY

Figure 5 - Connecting LYNDM-GSM/LYNXDM-IGSM

Antenna

The LYNXDM-GSM/LYNXDM-IGSM comes equipped with an external antenna that is intended for indoor use.

1. The external (indoor) antenna must be used.

2. AMPS antennas, such as the 7825-OC antenna, cannot be used with this product.

External Antenna

Connecting the external antenna to the port will automatically disconnect the internal antenna.

1. Connect the external indoor antenna onto the LYNXDM-GSM/LYNXDM-IGSM SMA connector.

2. Adjust the antenna as required.

09004-016-V0

TB 1

FOR EXTERNAL ANTENNA

50 OHM, MMCX ONLY

GSM

GPPS

WEB

MODE 2

MODE 1

RSSI

7720P PROGRAMMER PORT NOT

FOR TELEPHONE SERVICE USE!

PRIMARY POWER: 9 - 16.5 VAC

CURRENT: 900mA PEAK, 70mA STANDBY

BATTERY: 8V. 3.1 AHr FOR 24 Hr BACKUP

FCC:XXXXXXXXXX IC: YYYYYYYYYY

ANTENNA

ADAPTER

CABLE

EXTERNAL

ANTENNA

EXTERNAL

ANTENNA

PORT

Figure 6 - Installing the External Antenna

- 7 -

Programming the LYNXDM-GSM or LYNXDM-IGSM

1. Refer to the Programming Guide provided with the LYNXDM-GSM or LYNXDM-IGSM Communications

Module for additional information regarding programming and registration.

2. When programming is complete, snap the front case and the attached LYNXR-I Series control to the rear

case of the wall or desk mount.

Specifications

Mechanical

Dimensions: 8.5" x 6.25" x 1.5" (Wall Mount)

8.5" x 6.25" x 2.625" (Desk Mount)

Electrical

Current Drain: 35mA average standby, 500mA peak transmit

Module Fault Relay Output: Open collector, 12VDC, .25W max.

Input Trigger Levels: (V+) 2V – 13V

(V-) 0V – 1V

Transceiver Type: Tri-Band GSM/GPRS Class 10

Modulation: GMSK

Antenna: Internal GSM quad-band antenna 1.3 dBi gain

Band

Transmission

Frequency

(MHz)

Transmit

Power

(dBm)

Receive

Frequency

(MHz)

Receive

Sensitivity

(dBm)

Number

Channels

Channel

Spacing

(MHz)

Duplex

Separation

(kHz)

GSM 850 824-849 33 869-894 -107 124 200 45

GSM 1800 1710-1785 33 1805-1880 -106 374 200 95

GSM 1900 1850-1910 33 1930-1990 -105.5 299 200 80

Ethernet (LYNXDM-IGSM)

Network Standard: IEEE 802.3u compliant

Data Rate: 10Base-T / 100Base-T with auto detect

Ethernet Cable: Cat. 5 (min), MDI/MDI-X auto crossover

Environmental

Operating temperature: -20º to +55ºC

Storage temperature: -40º to +70ºC

Humidity: 0 to 95% relative humidity, non-condensing

Altitude: to 10,000 ft. operating, to 40,000 ft. storage

- 8 -

Glossary

AlarmNet-G AlarmNet GSM Cellular Network

AlarmNet-I AlarmNet Internet Network

GSM Global System for Mobile communications, which is an international standard for

digital mobile phone systems used for cellular communication.

GPRS General Packet Radio Service

IP Internet Protocol

IP Address A unique number consisting of four parts separated by periods, sometimes called a

"dotted quad.," for example: 204.17.29.11, assigned to every computer/workstation

connected to the Internet. IP numbers can be "static" (assigned and unchanging) or

"dynamic," assigned via DHCP at each and every startup.

ISP Internet Service Provider

MAC Media Access Code; located on the module label.

NOC Network Operations Center

SMS Short message Service

- 9 -

FCC AND INDUSTRY CANADA STATEMENT

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES AND RSS210 OF INDUSTRY CANADA. OPERATION IS SUBJECT

TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS

DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED

OPERATION.

THIS CLASS B DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES-003.

CET APPAREIL NUMÉRIQUE DE LA CLASSE B EST CONFORME À LA NORME NMB-003 DU CANADA.

FEDERAL COMMUNICATIONS COMMISSION (FCC) STATEMENT

This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following

statement for your information:

This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance

with the manufacturer's instructions, may cause interference to radio and television reception. It has been type tested and found

to comply with the limits for a Class B computing device in accordance with the specifications in Part 15 of FCC Rules, which are

designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee

that interference will not occur in a particular installation. If this equipment does cause interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference

by one or more of the following measures:

• If using an indoor antenna, have a quality outdoor antenna installed.

• Reorient the receiving antenna until interference is reduced or eliminated.

• Move the radio or television receiver away from the receiver/control.

• Move the antenna leads away from any wire runs to the receiver/control.

• Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch circuits.

If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. The user

or installer may find the following booklet prepared by the Federal Communications Commission helpful:

"Interference Handbook"

This booklet is available under Stock No. 004-000-00450-7 from the U.S. Government Printing Office, Washington, DC 20402.

The user shall not make any changes or modifications to the equipment unless authorized by the Installation and Setup Guide or

User Guide. Unauthorized changes or modifications could void the user's authority to operate the equipment.

- 10 -

-NOTES-

This manual suits for next models

Table of contents

Other Honeywell Control Unit manuals

Honeywell

Honeywell ADEMCO 5800RL Assembly instructions

Honeywell

Honeywell D15P User manual

Honeywell

Honeywell D22 User manual

Honeywell

Honeywell AVS User manual

Honeywell

Honeywell L5000-Wi-Fi User manual

Honeywell

Honeywell MAXON 8730 Series User manual

Honeywell

Honeywell NOTIFIER FCM-1 User manual

Honeywell

Honeywell D05T User manual

Honeywell

Honeywell ADEMCO 4204 User manual

Honeywell

Honeywell NetAXS-123 User manual

Honeywell

Honeywell Elster Jeavons S200 User manual

Honeywell

Honeywell DCCC6500 User manual

Honeywell

Honeywell 7800 SERIES User manual

Honeywell

Honeywell Silent knight 5895XL User manual

Honeywell

Honeywell QUIETPRO QP100Ex User manual

Honeywell

Honeywell Ex-Or CDH8U5 Installation and operation manual

Honeywell

Honeywell 7800 SERIES User manual

Honeywell

Honeywell VRW2 User manual

Honeywell

Honeywell SmartValve SV9520H User manual

Honeywell

Honeywell UCIP-GPRS User manual

Honeywell

Honeywell Notifier FCM-1 User manual

Honeywell

Honeywell HM700AFVALVE User manual

Honeywell

Honeywell VG.010A User manual

Honeywell

Honeywell HON HSV086 Manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual