Honeywell NOTIFIER INSPIRE E10 Training manual

Notiﬁer INSPIRE E10/E15

Fire Alarm Control Panels

Commissioning

Instructions

CONTENTS

RELATED DOCUMENTS

This guide does not describe any of the panel operating and

installation instructions, refer to:

INSPIRE E10/E15 Control Panel Operating Manual (Part

number HOP3389EN)

INSPIRE E10/E15 Control Panel Installation Manual

(Part number HOP1389EN)

CONVENTIONS

Where appropriate, in this manual there are advisory

warnings and cautions to remind you to consider safety

at all times, especially when following the procedures

described.

This symbol precedes a note that highlight

important information that is normally

hidden in the main text.

This symbol precedes information

that warns of danger that may result

in serious injury or death, also used

as a caution to prevent damage to the

equipment.

This symbol precedes information about

compliance with standard(s).

ABBREVIATIONS

CIE Control and Indicating Equipment

CPU Central Processing Unit

E10 Smaller 10U size Panel enclosure

E15 Larger 15U size Panel enclosure

EMC Electromagnetic compatibility

FARE Fire Alarm Routing Equipment

FRE Fault Routing Equipment

FPE Fire Protection Equipment

HMI HumanMachine Interface

IO or I/O Input or Output

LED Light emitting diode (light)

MCP Manual call point

OC or O/C Open circuit

RAL European colour matching system

SC or S/C Short circuit

SELV Separated Extra Low Voltage

PE Protective Earth

PELV Protected ExtraLow voltage

PSE Power Supply Equipment

Notiﬁer INSPIRE E10/E15 Control Panels - Commissioning

Introduction

The purpose of this manual is to provide the user with recommendations on procedure for Commissioning of

INSPIRE Fire Alarm Control Panel based Fire Control System.

Commissioning

To bring the Notiﬁer INSPIRE E10/E15 Control panel into an operational state ready for conﬁguration, follow the

steps detailed below. Information on how to conﬁgure the panel is given in the Notiﬁer INSPIRE E10/E15 Control

Panel Conﬁguration Tool Manual.

The Notiﬁer INSPIRE E10/E15 Control panel provides comprehensive fault monitoring and diagnostic routines

which will prove very useful during system commissioning. Any fault message displayed at the panel carry a

meaning and possible action that a trained engineer can take to remedy the fault, see section headed Messages

and their meaning.

The following must be remembered about FAULT conditions when commissioning the Notiﬁer INSPIRE E10/E15

Control panel, faults can result from:

A conﬁguration mismatch between the site design, installation of panel and wiring of external equipment, or

External conditions, such as the proximity of a strong RFI source, having an adverse effect on the panel, or

The failure of a panel module and / or the PSU.

PRELIMINARY CHECKS

Before initial power connection, check that:

01 All modules are correctly seated into the respective module carrier slots.

02 All internal wiring is properly connected.

03 Ensure the loop wiring and external circuits have NOT, at this stage, been connected with terminal blocks

ﬁtted to respective terminal pins on module carrier.

04 The appropriate end-of-line devices are connected, such as to I/O channel circuit.

Notiﬁer INSPIRE E10/E15 Control Panels - Commissioning

Ensure Modules are installed into their allowed slot locations

It is required that the Charger module is always ﬁtted in Slot 1 of the module carrier and

CPU Module ﬁtted in Slot 2 of Module Carrier.

ROW 1

ROW 2



Slot 1

Slot 2

Slot 3

Slot 4

Slot 5

Slot 6

Slot 7

Slot 8

Slot 9

Slot 10

Slot 11

Slot 12

Charger

E10 Panel range

E15 Panel range

6/2-slots

Module

Carriers

Link module

for Module

carriers

expansion

Termination

Module for

Battery &

PSU cables

2-Rows Link

Modules with

power and Ethernet

patch cables

ROW 1ROW 2

E10

ROW 1



Allowed to be fitted in these

slots of Module carriers.

X - Not allowed in these

slots of Module Carriers

E15

- 6-slots, supplied fitted

- Not applicable

Modules:

- Loop Opal 2X

- COM Dual (FAT/FBF)

- FIRE/FAULT routing

- COM Serial (RS232/RS485

- I/O 4-CH

- NET ID2NET



Slot 13

Slot 14

/

E10 E15

- 2-slots Extension

optional

CPU

/

E10 E15

/

E10 E15

E10

E15



E10

E15

IMPORTANT

1 2 3 4 5 6 7 8 9 10

123456

789

10 11 12 13 14

Slot No:->

Slot No.

Module carriers

- panel range.

E10 E15

Module carriers

Module: Module:

Commissioning

SENSORS AND MODULES CHECKS

Each device has an associated instruction leaﬂet showing the correct interconnections for various applications.

Survey the site to check and ensure devices are installed in the location identiﬁed on 'As ﬁtted system wiring

drawings' and according to the instructions.

The Notiﬁer INSPIRE E10/E15 Control Panel support supports devices incorporating internal isolators, providing

the bases with the additional positive leg loop wiring connectors (type B501 AP) are used. However, devices will

work satisfactorily when used with bases without these additional wiring connectors except the internal isolator,

when ﬁtted, cannot be operated.

The Notiﬁer INSPIRE E10/E15 Control panel Dual Loop module Opal (HOP433100) has the capacity to

allows connection of up to 318 loop OPAL devices per analogue loop, consisting of up to 159 detectors and 159

modules.

A loop can operate in legacy CLIP mode which can be activated through a dedicated license. The capacity of a

CLIP loop is limited to 99 detectors + 99 other devices

Notiﬁer INSPIRE E10/E15 Control Panels - Commissioning

LOOP WIRING TESTS

Refer to the module installation instructions to identify the terminals for cable connections.

NEVER use a high-voltage tester on the detection loop.

Once any loop devices are connected, no high-voltage testers, such as Megger may be used on the loop circuit;

low-voltage testers, such as multimeter, may be used.

With isolators in each device the positive conductor of the loop will be open circuit.

In general

Check the continuity of each leg of the loop and measure the end-to-end resistance. We recommend that the

system must be wired using 2-core cable only.

Check the continuity of the cable screen and measure end-to-end resistance, which must be a very low

resistance value .

Check also there is no continuity between cable screen and loop +ve and -ve wires of the loop.

Commissioning

Typical connections of addressable devices to a loop are shown below:

LOOP OPAL X2

1 2 3 4 5

6 7 8 9 10

1Loop 1 OUT +VE

2Loop 1 OUT -VE

4Loop 1 IN +VE

5Loop 1 IN -VE

6Loop 2 OUT +VE

7Loop 2 OUT -VE

9Loop 2 IN +VE

10 Loop 2 IN -VE

1234

6789101112

CBA

1234

EOL

Loop Input

2 Input 1 Output Interface

Manual Call Point

Loop Output

Loop Outout

Detector

Control panel

Other manuals for NOTIFIER INSPIRE E10

This manual suits for next models

Table of contents

Other Honeywell Control Panel manuals

Honeywell

Honeywell MRP-2002 User manual

Honeywell

Honeywell Domonial CMI 800++ User guide

Honeywell

Honeywell Ademco Accord User manual

Honeywell

Honeywell Vigilon Plus User manual

Honeywell

Honeywell 013080 Instruction manual

Honeywell

Honeywell AQ252 Series User manual

Honeywell

Honeywell Galaxy 2 Series User manual

Honeywell

Honeywell HPZC10 Series User manual

Honeywell

Honeywell GX-Series Assembly instructions

Honeywell

Honeywell IFP-300 Technical specifications

Honeywell

Honeywell Gamewell Flex 402 User manual

Honeywell

Honeywell NOTIFIER ID2000 Series Guide

Honeywell

Honeywell Silent Knight SKE Series User manual

Honeywell

Honeywell THOR VM1 User manual

Honeywell

Honeywell TrolaTemp MABS EZ-2 Operation manual

Honeywell

Honeywell Tuxedo Touch Wi-Fi Assembly instructions

Honeywell

Honeywell TrueZONE HZ432 User manual

Honeywell

Honeywell Notifier ST.PL4+ User manual

Honeywell

Honeywell Fire-Lite Alarms MS-5UD Series User manual

Honeywell

Honeywell AQ250 Series Operation manual

Honeywell

Honeywell CM737 Installation instructions

Honeywell

Honeywell NOTIFIER SFP-10UD Series User manual

Honeywell

Honeywell NOTIFIER AM1000 User manual

Honeywell

Honeywell Vigilon 4 loop Installation and operation manual

Popular Control Panel manuals by other brands

RDZ

RDZ PC-HRX user manual

STG-BEIKIRCH

STG-BEIKIRCH MZ3 operation instruction

Efka

Efka Variocontrol V810 instruction manual

Cebora

Cebora 208-10 instruction manual

AMX

AMX AutoPatch CP-15 instruction manual

Satel

Satel CA-6 KLED-S user manual

Evolution

Evolution IQ plus 800 installation manual

Fagor

Fagor 8040 TCO CNC operating manual

Trane

Trane ComfortLink II XL950 Control user guide

AKO

AKO PROCool AKO-17635-2 quick guide

ABB

ABB 6136/30M-101 operating instructions

Telikou

Telikou BK-603 Belt Pack instruction manual

Mapei

Mapei Mapeheat Thermo Touch user guide

Bosch

Bosch D9412GV4 owner's manual

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 user manual

Sminn

Sminn BOX L VF1L EI instruction manual

Balboa

Balboa TP600 user manual

Nice

Nice HSCU1 Instructions and warnings for installation and use