Honeywell PCR191W User manual
PCR191W – Atomic Projection Clock
HOW DO I SET THE TIME ZONE ON MY PCR191W?
Select the US Time Zone by pressing and holding the UP (+) button for 3 seconds.
Keep holding the UP (+) button until the desired US Time Zone (Pacific, Mountain, Central or
Eastern) is highlighted on the display’s US map, located to the right of the time display and above
the seconds.
Release the UP (+) button. The Time Zone is set.
HOW MANY ALARMS CAN BE SET ON MY PCR191W?
The PCR191W has dual alarm with programmable snooze interval. If any of the alarms is
activated, it will sound at the set time and the alarm icon will flash Mondays through Fridays.
HOW TO SET THE TIME ALARM?
Press the MODE button to select the desired alarm to be set – ALARM 1 or ALARM 2. The default
alarm time for ALARM 1 is set to “6:00AM”.
• Press and hold button for three seconds. The hour digit will begin to flash.
• Select the desired hour using DOWN (-) or UP (+) buttons.
• Press button to confirm selected hour and move to minute’s adjustment. The minute digits
will flash.
• Enter the minutes using DOWN (-) or UP (+) buttons.
• Press the button confirming the ALARM 1 time is set.
• Use the same procedure for setting the time for ALARM 2
HOW TO DISABLE THE TIME ALARM?
Press or selecting the ALARM 1 or ALARM 2 – an appropriate bell icon will
disappear from the display showing that alarm is disabled.
HOW DO I SET THE LANGUAGE FOR THE DAY OF THE WEEK?
Press and hold DOWN (-) button until the language abbreviation will be displayed – EN (for
English), SP (for Spanish) or FR (for French). Once the desired language abbreviation is displayed,
release the DOWN (-) button, and the day of the week will be displayed in selected language.
HOW DO I SET 12 OR 24 HOUR TIME FORMAT?
To set 12 hour time format, press UP (+) button once, and “AM” or “PM” will appear to the left of
the time display.
To set 24 hour time format, press UP arrow button once until “AM” or “PM” abbreviation will
disappear from the time display.
HOW DO I CHANGE A TEMPERATURE UNIT IN MY PCR191W?
The temperature measurement unit (Cº or Fº) can be changed only through entering clock setting
procedure:
1. Press and hold MODE for 3 seconds - the year digit will flash.
2. Press MODE once - the month digit will flash. Press UP (+) or DOWN (-) buttons to select the
month.
If correct month is displayed press MODE button once to confirm and move to the date mode
selection (date digit will flash)
3. Press UP (+) or DOWN (-) buttons to select the date.
If correct date is displayed press MODE button once to confirm and move to the hour format
selection (“12” digits will flash)
4. Press UP (+) or DOWN (-) buttons to select the hour
If correct hour is displayed press MODE button once to confirm and move to the minutes selection
(minutes digits will flash)
5. Press UP (+) or DOWN (-) buttons to select the minutes
If correct minutes are displayed press MODE button once to confirm and move to the temperature
unit selection (temperature fill flash)
6. Press UP (+) or DOWN (-) buttons to select the temperature unit: “Fº” for Fahrenheit or “Cº” for
Celsius.
If correct temperature unit is displayed press MODE button once to confirm the setting and exit
from clock programming mode.
WHERE IS US ATOMIC CLOCK LOCATED?
US Atomic clock is located at Fort Collins outside Boulder, Colorado, and is operated by the US
Government
WILL MY ATOMIC TIME UNIT WORK IN ALASKA AND HAWAII?
If used in Alaska and Hawaii, the Atomic Time clocks will not receive the RF signal from the US
Atomic Clock during the normal daylight hours. The 50kW radio signal transmitted at 60 kHz
frequency covers the Continental United States (CONUS) and reaches parts of Alaska and Hawaii
during the night-time hours. However, this clock can be set manually if the signal from Boulder,
Colorado is not able to reach the locations that geographically are not in the US Atomic Clock Time
Signal coverage area.
HOW TO ENABLE ATOMIC TIME SIGNAL RECEPTION MANUALLY?
1. Press and hold UP(+) and DOWN(-) buttons at the same time for 3 seconds and the atomic time
radio reception icon located above the seconds will disappear.
2. Press and hold UP (+) and DOWN (-) buttons at the same time for 3 seconds again enabling
atomic time radio receiver. The radio reception icon will start flashing showing that the unit is
searching for the atomic time signal.
MY PCR191W DID NOT RECEIVE ATOMIC TIME SIGNAL DURING INITIAL SETUP. HOW CAN
THIS BE FIXED?
Please consider the following when atomic time is not set during the initial setup:
• During night-time hours, atmospheric conditions improve radio signal reception. A single daily
reception is sufficient enough to keep the clock accuracy within milliseconds.
• Unit should be positioned 8 feet (2 meters) from interference sources such as a TV, computer,
microwave, etc.
• The signal reception is weakened within concrete walls found in basements or office buildings.
Place the unit near the window for best reception.
Once the atomic time signal is received, the date and time will be set automatically, and the atomic
time reception icon will appear.
Your unit’s atomic clock is programmed to search for the atomic time signal daily each hour
between 1:00 am and 4:30 am. Once the time signal has been successfully received, the time and
date will be updated automatically.
Usually Atomic Time Signal is picked up overnight, but in some cases it may take up to 72 hours.
HOW TO ACTIVATE THE BACKLIGHT?
You can activate the backlight for a short time period by pressing LIGHT/SNOOZE button on the
top.
HOW LONG DOES THE BACKLIGHT STAY ON?
The backlight will stay on for 3 seconds if the LIGHT/SNOOZE button is pressed.
HOW LONG THE BATTERIES LAST IN THE UNIT?
The average battery life in the device is 12 months.
HOW LONG THE PROJECTION WILL STAY ON?
Your product is able to project the time and indoor or outdoor temperature image for a short period
of time (5-6 seconds), or continuously (when the AC/DC adapter is connected).
HOW DO I SET MY PCR191W TO THE MODE PROJECTING TIME OR INDOOR
TEMPERATURE?
Press and hold FLIP button for 2 seconds and the projected image will alternate between the time
and indoor temperature information every 5 seconds
\
Table of contents
Other Honeywell Clock manuals
Honeywell
Honeywell TE211W - Atomic Clock With Wireless... User manual
Honeywell
Honeywell PCR11ELW User manual
Honeywell
Honeywell PCR191W User manual
Honeywell
Honeywell RCW33W - Atomic Wall Clock User manual
Honeywell
Honeywell PCR325W User manual
Honeywell
Honeywell CL600A-1001 Troubleshooting guide
Honeywell
Honeywell TRS-3300 User manual
Honeywell
Honeywell RC402W User manual
Honeywell
Honeywell PCR19W User manual
Popular Clock manuals by other brands
Silicon Laboratories
Silicon Laboratories SI5324 manual
Heathkit
Heathkit GC-1005 Assembly manual
Oregon Scientific
Oregon Scientific PRYSMA RMR221P manual
Andrew O'Malley
Andrew O'Malley DOTKLOK Assembly instructions
ALGE-Timing
ALGE-Timing ASC3 manual
Bodet
Bodet Profil 960 Installation and operating instructions
Progetti
Progetti KALIMERO Directions
La Crosse Technology
La Crosse Technology WT-3141b Quick setup instructions
La Crosse Technology
La Crosse Technology W86531 owner's manual
Sharp
Sharp SPC900 instruction manual
La Crosse Technology
La Crosse Technology 404-50447 quick start guide
Datexx
Datexx DF0063 quick guide