HOMEDEPOT KSTFA120AG User manual

Instruction Manual

ETLus Electric Fan

KSTFA120AG

For Household Use Only

IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

This fan has a polarized plug (one blade is wider than the other). To reduce the

risk of electric shock, this plug is intended to fit in a polarized outlet only one way.

If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit,

contact a qualified electrician. Do not attempt to defeat this safety feature.

This product employs overload protection (fuse). A blown fuse indicates an

overload or short-circuit situation. If the fuse blows, unplug the product from the

outlet. Replace the fuse as per the user servicing instructions (follow product

marking for proper fuse rating) and check the product, If the replacement fuse

blows, a short-circuit may be present and the product should be discarded or

returned to an authorized service facility for examination and/or repair.

WARNING – To Reduce The Risk Of Fire Or Electric Shock, Do Not Use This

Fan With Any Solid-State Speed Control Device.

WARNING – To Reduce The Risk Of Electric Shock, Do Not Expose to Water

or Rain.

WARNING – This is a fan – not a toy! To reduce the risk of personal injury and

electric shock, it should not be played with or placed where small children can

reach it.

When using electric appliances, basic safety precautions should always be

followed, including the following:

1. Do unplug or disconnect the appliance from the power supply before servicing.

2. Do not use gasoline, thinners, solvents, ammonias or other chemicals for

cleaning.

3. Do clean your fan regularly. Refer to the Cleaning instructions provided. Never

clean the fan in any manner other than as instructed in this manual.

4. Do not operate any fan with a damaged cord or plug. Discard fan or return to

an authorized service facility for examination and/or repair.

5. Do not run cord under carpeting. Do not cover cord with throw rugs, runners,

or similar coverings. Do not route cord under furniture or appliances. Arrange

cord away from traffic area and where it will not be tripped over.

6. Do not use this product outdoors.

7. Do not use this product on wet surfaces.

8. Do not use this product in a bathtub or shower.

9. Do not use near furnaces, fireplaces, stove or other high-temperature heat

sources.

10. Do not immerse this product in water or allow water to drip into the motor

housing.

11. Do not position this fan too close to draperies because they may be drawn into

the rear guard, cutting off airflow.

SAVE THESE INSTRUCTIONS

P1-14606

P2-14606

User Servicing Instructions

Grasp plug and remove from the receptacle or other outlet device. Do not unplug

by pulling on cord. Open fuse cover (A.) by sliding access cover on top of

attachment plug towards blades. Remove fuse carefully (B.) by gently prying out

the ends of the fuse from the receptacle.

Risk of fire. Replace fuse only with 2.5 Amp, 125 Volt fuse.

Install replacement fuse (C.) by first placing the end of the fuse into the fuse

receptacle which is opposite of the blades of the plug, then carefully push in the

other end. Only push against the metal end of the fuse, not the glass center

portion. Close the fuse access cover (D.) by sliding the cover back into the plug

until it is completely closed, latches and is flush with the face of the plug.

Risk of fire. Do not replace attachment plug. Contains a safety device (fuse , AFCI,

LCDI) that should not be removed. Discard product if the attachment plug is

damaged.

Know Your Fan

Parts and Their Function

Parts Function

●Height adjust button

Use only when higher position required.

Pressing the height adjust button, pull

the slide pipe upwards.

When lower position required, just push

the slide pipe downwards.

You can adjust the height in 2 steps.

Caution: Be careful not to pinch fingers.

●Swivel button

Press down…Swivel starts

Pull up…Swivel stops

P3-14606

P4-14606

How to Assemble

CAUTION:

Do not insert the plug into the power point before assembly is complete.

(May cause electric shock or injury)

Do not press height adjustment button while fan and fan guard are

detached.

(The motor section (slide pipe) may jump out of stand, causing injury)

1. Fix the stand onto the base

●Remove the motor shaft cover.

●Check the stand direction by the

indication of front and back of

the base and stand, insert the front

protusions of stand into the concav

-es of the base, then push the

whole stand part down onto the

base until it is fitted in firmly.

●Placing the motor shaft upward,

then fix the stand and base by

turning the base fixing ring

providedclockwise.

Attention:

● Base fixing ring is temporarily attached on bottom of stand. Unscrew it

When you assemble the fan.

● Do not forcibly push the stand down onto the base. May cause damage.

● Do not put the stand onto the base in wrong direction. May cause damage.

● Do not press the height adjust button while assembling. May cause injury,

damage to the product or machine failure.

2. Fix Rear Guard and Fan Blade

●Couple protrusions (three) on the motor section to concaves (three) on the

rear guard.

●Fix them firmly by turning the guard fixing ring toward [fasten].

●Couple the pin on the motor shaft and the concave on the fan blade and

insert the fan part into the motor part. Then pressing the fan part towards

the motor part and turn the fan blade cap toward [fasten] to fix them firmly.

Attention:

● If the fan blade cap is not fastened firmly enough, fan blade may come off,

causing injury.

● Be careful not to be injured by motor shaft or pin when assembling or

disassembling.

3. Fix Front Guard

●Hold the rear guard and press the front guard

toward the rear guard from the top, making sure

that the whole periphery of the front guard clicks

into the rear guard.

●Clip the front and rear guard together

with the clip on the guard.

Attention:

● If the front guard is not clipped together

firmly enough, the front guard may come off, causing injury.

How to Take off Front Guard

Unplug first and stop the ratation of the fan blade. Then undo the clip and pull the

grip on the guard ring, pressing the front guard down.

Attention: Do not pull by the clip. May damage the clip.

P5-14606

How to Operate

ON/OFF Operation On/Off

SPEED LOW - MID - HIGH

TIMER Set TIME (0.5-1-2-4-stop timer function) hours

COMFORT Set Comfort mode

Ready

Insert the power plug into a 120V power point.

Start

Switch on by pushing [ON/OFF] button.

(The fan starts at the speed “LOW” )

Pushing [ON/OFF] button again to end the operation.

Speed setting

Select your preferred fan speed by pushing [SPEED] button.

LOW–MID-HIGH

(Each press will change the speed and the speed indicator lamp)

Timer setting

Select at your desired time (0.5-1-2-4 Hour) by pushing [TIMER] button.

0.5 – 1 – 2 – 4 – stop timer function

(Each press will change the time and the time indicator lamp)

After the time you set, the fan will stop automatically.

Rhythm mode setting

Set Rhythm mode by pushing [RHY] button. Push it again, Rhythm mode is

canceled.

(Each press will change the mode and the Rhythm indicator lamp)

CAUTION:

● Do not cover remote control reception area.

(If there is any obstacle between the reception area and the remote control, the

remote control will not work)

● Handle remote control carefully. Do not drop, step on, or spray water on the

Remote control.

(May damage or break.)

TiltingAdjustment

Always switch the fan off before making a tilt adjustment. The air flow can be

P6-14606

P7-14606

adjusted upward or downward simply by moving the guard up or down.

CAUTION: In the case of no blades installed, please don't run the product.

Operating Block Diagram Analysis

Rhythm Mode:

At Low Speed:

At Mid Speed:

At High Speed:

Maintenance and Storage

WARNING

When cleaning, the plug must be removed from the power point. Do not

handle plug with wet hands.

[May cause electric shock or injury.]

Do not press the height adjustment button while the fan and fan guard are

detached.

[The motor section (slide pipe) may jump out of the stand part, causing injury.]

When disassembling the base or stand, unplug plug from the power point.

[May cause electric shock or injury.]

How to Clean

P8-14606

P9-14606

Disassemble the fan and guard in the inverse order of assembling. Wash off dirt

and dust with well squeezed wet soft cloth with water or neutral detergent, then

wipe off the detergent.

CAUTION:

Do not use volatile solvents such as gasoline, thinner, benzene, wax,

kerosene, alcohol, polishing powder, or alkaline detergent. These may

discolour or damage the machine, causing injury.

If using a chemical dust cloth, follow those instruction.

Do not oil plastic parts. May cause discoloration or injury from damaged parts.

How to Store

Disassemble fan, guard, stand and base in the inverse order of assembling.

Clean the motor shaft and oil put the motor shaft cover back to the motor shaft.

Store these parts in the box provided at purchase and keep in a dry place.

CAUTION:

When the fan is not facing front, do not force the fan to turn. Use the swivel

function.

Clean the fan and guard referrring to [ How to Clean], then store it.

How to Disassemble the Base

1. Put the motor shaft upward, then unscrew fixing ring by turning anticlockwise.

(Refer to the drawing at below)

Holding the base firmly, then pull the base.

CAUTION:

If the motor shaft is facing downward, the fan will become unstable and may

damage the product or floor.

When putting the motor shaft down, the fan is unstable. May cause machine

failure and damage to floor.

2. Hold the stand firmly and gently lift and remove the base.

Technical Specifications

oltage 120V~60Hz Power Consumption ?A or ?W

Fan Speed

Time

Product Holde

Join-One Electric (Shenzhen) Co.,Ltd

Subject to technical modification

P10-14606

P11-14606

Table of contents

Other HOMEDEPOT Fan manuals

HOMEDEPOT

HOMEDEPOT CFN-1053 User manual

HOMEDEPOT

HOMEDEPOT YG528-BN User manual

HOMEDEPOT

HOMEDEPOT EVERBILT CX1000AMEVB User manual

HOMEDEPOT

HOMEDEPOT Trice YG269C-BN User manual

HOMEDEPOT

HOMEDEPOT CFN-1056 User manual

HOMEDEPOT

HOMEDEPOT FC132-BJRL User manual

HOMEDEPOT

HOMEDEPOT Comercial Electric SFD-250B User manual

HOMEDEPOT

HOMEDEPOT CFN-1203 User manual

HOMEDEPOT

HOMEDEPOT Merra CFN-1054 User manual

HOMEDEPOT

HOMEDEPOT 1005 820 129 User manual

HOMEDEPOT

HOMEDEPOT AL383LED-BK User manual

HOMEDEPOT

HOMEDEPOT FZ-12A2 User manual

HOMEDEPOT

HOMEDEPOT SHARON User manual

HOMEDEPOT

HOMEDEPOT AL383-WH User manual

HOMEDEPOT

HOMEDEPOT B552QI-BN User manual

HOMEDEPOT

HOMEDEPOT 42NB0814 User manual

HOMEDEPOT

HOMEDEPOT YG269BP-MWH User manual

HOMEDEPOT

HOMEDEPOT MONTGOMERY DB91-WH User manual

HOMEDEPOT

HOMEDEPOT DB30TBN-LP User manual

HOMEDEPOT

HOMEDEPOT AERO BREEZE 60-EVO User manual

HOMEDEPOT

HOMEDEPOT TRICE User manual

HOMEDEPOT

HOMEDEPOT FL-804 User manual

HOMEDEPOT

HOMEDEPOT F3501 Manual

HOMEDEPOT

HOMEDEPOT Hugger AL383LED-BN User manual

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual