HOMEDEPOT CFN-1203 User manual

CFN-1203

Instruction Manual

V20221018

Read Carefully Before Use

Keep for Future Reference

TABLE OF CONTENTS

INTRODUCTION

Before beginning installation of this product, read the package list on page 2 and ensure all parts

are present and display no defects. If any part is missing or damaged, contact customer service

and do not attempt to install the product. Read all of the safety information on page 3 before

installation or use.

Estimated assembly time: 120 minutes

Additional tools required for assembly:

Electrical tape, flathead & Phillips screwdriver, pliers, safety glasses, ladder, and wire strippers

Additional helpful tools:

AC tester light, tape measure, wiring handbook, and wire cutters

Introduction ·························································································· 1

Package Contents ················································································· 2

Safety Information·················································································· 3

Preparation ·························································································· 4

Initial Installation ··················································································· 5

Downrod Mounting ················································································ 5

Circuit Connections ··············································································· 6

Canopy and Cover Installation ································································· 7

Fan Blade Installation ············································································· 7

Light Installation ··················································································· 8

Color Temperature Adjustment ································································· 8

Remote Control Operation ······································································· 9

Troubleshooting ·················································································· 10

Contact Information·············································································· 10

a. Fan Blades (×6)

b. Ceiling Mounting Bracket

c. Canopy

d. Canopy Cover

e. Downrod

f. Coupling Cover

g. Fan Motor Assembly

h. Blade Holders (×6)

i. Light Plate

j. LED Light Kit

k. Glass Shade

l. Remote Control

m. Receiver

n. Mounting Screws (×4)

Mounting Bolts (×2)

Spring Washers (×4)

Star Washers (×4)

Blade Bolts (×18)

Bolt Nuts (×18)

Flat Washers (×23)

Wire Nuts (×8)

Balance Kit

PACKAGE CONTENTS

1. To reduce the risk of electric shock, ensure electricity has been turned off at the circuit

breaker or fuse box before beginning.

2. All wiring must be in accordance with national and local electrical codes. Electrical

installation should be performed by a qualified licensed electrician.

3. This fan is suitable for use with solid-state speed controls.

4. To reduce the risk of personal injury, use only the screws and washers provided with

the outlet box for mounting to the outlet box. Most outlet boxes commonly used for

the support of lighting fixtures are not acceptable for fan support and may need to be

replaced. Consult a qualified electrician if in doubt.

5. The outlet box and support structure MUST be securely mounted and capable of reliably

supporting a minimum of 50 pounds. Use only UL listed outlet boxes marked "FOR

FAN SUPPORT".

6. After marking electrical connections, spliced conductors should be turned upward and

pushed carefully up into outlet box. The wires should be spread apart with the grounded

conductor and the equipment-grounding conductor on one side of the outlet box.

7. The fan must be mounted with a minimum of 7 feet clearance from the trailing edge of

the blades to the floor.

8. Do not use the reverse switch while the fan blades are in motion. To prevent damage

and ensure long use, the fan must be turned off and the blades stopped before

reversing direction.

9. Do not place objects in the path of the blades.

10. Exercise caution when working around or cleaning the fan.

11. Use a soft dry cloth to clean the fan body and blades. Do not use water or detergent.

12. The electrical diagrams provided herein are for reference only. Light kits that are not

packaged with the fan must be UL listed and suitable for use with this fan. Switches must

be UL general use switches. Refer to their separate instructions for proper assembly.

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, & PERSONAL INJURY,

MOUNT FAN TO AN OUTLET BOX MARKED “ACCEPTABLE FOR FAN SUPPORT”.

SAFETY INFORMATION

Warning!

NEVER BEND THE BLADE BRACKETS/FLANGES FOR ANY REASON.

PREPARATION

3. Choose a Suitable Location

Ensure the blades will be at least 30 inches from any

obstruction and at least 7 feet above the floor. In

locations without a ceiling joist, a hanger support bar

may be required. Do not install in clamp locations.

Failure to disconnect the power supply prior to

installation may result in serious injury or death.

Use only on flat ceilings

Do not use on slanted surfaces

7 feet

30 inches

1. Turn Off Your Power

Begin installation by removing fuses or turning off circuit

breakers to the wiring you will be using. Use your compatible

UL listed outlet box if you already have one installed.

2. Choose Your Mounting Position

If you need to install a new UL listed outlet box, secure it

directly to your building's structure using appropriate fasteners

and materials. Do not use plastic boxes. The outlet box and its

supports must be able to support the MOVING weight of the

fan (at least 50 lb.) and be rated for fan support.

Step 1. Pass the 120V supply wires through the center hole in the ceiling mounting

bracket.

Step 2. Secure the ceiling mounting bracket to the outlet box with the provided mounting

screws or bolts and spring or star washers.

INITIAL INSTALLATION

Outlet Box

Ceiling Mounting Bracket

Hook

120V Wires

Mounting Screws/Bolts

Washers

Step 1. Remove the hitch and lock pins. Loosen

the pre-installed bolts on the top of the

motor assembly.

Step 2. Slip the canopy, canopy cover, and

coupling cover onto the downrod. Feed

the lead wires from the fan motor through

the downrod. Install the downrod onto the

coupling.

Step 3. Insert the hitch pin through the downrod

and then re-install the retaining clip.

Retighten the bolts.

Step 4. Place the downrod ball into the ceiling

mounting bracket socket. Rotate the

entire assembly until the tab has dropped

into its slot and sits firmly. The entire

motor assembly should not rotate (left or

right) when seated properly.

Failure to reattach the hitch pin and/or properly

seat the downrod can cause the fan to fall from

the ceiling during operation.

DO NOT use the fan before ensuring it is

properly secured and the motor cannot

rotate.

Bolts

Hitch Pin Retaining Clip

Downrod

Canopy

Canopy Cover

Coupling Cover

Downrod

DOWNROD MOUNTING

CIRCUIT CONNECTIONS

Step 1. Insert the receiver into the tray with

the receiver facing the ceiling. For

best performance, make sure the

white antenna, on the end of the

receiver, remains extended and not

tangled with any of the electrical wires.

Step 2. Connect the 4 colored wires from the

remote receiver to the 4 identically

colored lead wires from the fan motor.

Secure each set with the provided

wire nuts.

Step 3. Connect the 2 colored wires from the

remote receiver to the 2 identically

colored lead wires from the outlet box.

Secure each set with the provided

wire nuts.

Step 4. Connect the green or bare copper

ground wire from the outlet box to the

ground wires from the ceiling

mounting bracket and the ceiling fan.

Separate the white and green

connections from the black wire

connections, which should be kept

on opposite sides of the outlet box.

Ensure there are no loose wires or connections,

and secure connectors with electrical tape.

Again, ensure that the power has

been cut before working with the

wiring. Use the wire nuts provided

with your fan.

Ceiling

Mounting

Bracket

Receiver

White(Zero line)

Brown (Forward and reverse)

Black(motor)

Blue(light)

Outlet Box

Green or Bare

Copper (ground)

Black (“AC IN L”)

Black (hot)

White (“AC IN N”)

White (neutral)

Blue

Brown

White

Black

Blue

Brown

White

Black

Receiver

Receiver Head

CANOPY AND COVER INSTALLATION

FAN BLADE INSTALLATION

Step 1. Fit a blade in place on a blade holder

and secure it using three blade bolts,

bolt nuts, and flat washers.

Step 2. Making sure the blade is straight,

tighten the nuts.

Step 3. Remove the bolt pre-installed on the

fan motor assembly.

Step 4. Install the blade holder underneath

the motor and secure it by replacing

and retightening the bolt.

Step 5. Repeat for the remaining blades and

blade holders.

Step 1. Tuck all the connections neatly into the outlet box.

Step 2. Slide the canopy up to the ceiling mounting bracket and place the key hole slots

over the mounting screws or bolts on the bracket. Rotate the canopy until the

screw heads lock in place at the narrow section of the key hole.

Step 3. Attach the canopy cover to the bottom of the canopy and screw it into place.

Ceiling Mounting

Bracket

Canopy

Canopy Cover

Mounting Screws/Bolts

Outlet Box

Bolt Nut

Flat Washer

Bolt

Blade

Blade Holder

Wire Connectors

LED Light Kit

Light Plate

Bolts

Glass Shade

LIGHT INSTALLATION

COLOR TEMPERATURE ADJUSTMENT

The LED light has 3 different color setting: Warm White (3000K), Daylight (4500K), and

Cool White (6000K). To adjust the light settings,

1. Press LIGHT on the remote control to turn on the LED light.

2. Press LIGHT again to turn off the light.

3. Press LIGHT to turn on the light once more with the next color temperature in order.

Repeat these steps to toggle among 3 color temperatures.

Step 1. Remove the pre-installed bolts on

the fan motor assembly.

Step 2. Feed the wire connectors through

the middle of the light plate. Install

the light plate onto the motor

assembly and secure it by replacing

and retightening the bolts.

Step 3. Connect the LED light kit to the light

plate using its magnetic suction-cup

bolts.

Step 4. Connect the wire plugs of the LED

light kit to the wire connectors (blue

to blue and white to white).

Step 5. Fit the glass shade onto the light

plate and screw it into place.

Ensure it is firmly connected to

avoid loosening during use.

REMOTE CONTROL OPERATION

DO NOT press R/F while the fan is turning. Wait for it to stop completely before changing

the direction of its rotation.

This remote operates with a range of 30 feet (10 m). It uses 2 1.5V AAA batteries (not

included). If the remote will not be used for a prolonged period, it is recommended to

remove the batteries for better service life.

Starts the fan at low speed

Starts the fan at medium speed

Starts the fan at high speed

Stops the fan

Turns the light on or off

Runs the fan for 1 hour and then turns it off

Runs the fan for 2 hours and then turns it off

Runs the fan for 4 hours and then turns it off

Reverses the fan’s direction

Key Function

LOW

MED

STOP

LIGHT

R/F

Install the remote control holder onto any wall or suitable flat surface using the two steel screws.

Table of contents

Other HOMEDEPOT Fan manuals

HOMEDEPOT

HOMEDEPOT Home Decorators Conner User manual

HOMEDEPOT

HOMEDEPOT YG269B-EB User manual

HOMEDEPOT

HOMEDEPOT B552QI-BN User manual

HOMEDEPOT

HOMEDEPOT TRICE User manual

HOMEDEPOT

HOMEDEPOT YG528-BN User manual

HOMEDEPOT

HOMEDEPOT AL383-WH User manual

HOMEDEPOT

HOMEDEPOT FZ-12A2 User manual

HOMEDEPOT

HOMEDEPOT MONTGOMERY DB91-WH User manual

HOMEDEPOT

HOMEDEPOT Commercial Electric SFD5-400B User manual

HOMEDEPOT

HOMEDEPOT YG269BP-MWH User manual

HOMEDEPOT

HOMEDEPOT Comercial Electric SFD-250B User manual

HOMEDEPOT

HOMEDEPOT EVERBILT CX1000AMEVB User manual

HOMEDEPOT

HOMEDEPOT 1005 820 129 User manual

HOMEDEPOT

HOMEDEPOT FL-804 User manual

HOMEDEPOT

HOMEDEPOT Trice YG269C-BN User manual

HOMEDEPOT

HOMEDEPOT AERO BREEZE 60-EVO User manual

HOMEDEPOT

HOMEDEPOT CFN-1056 User manual

HOMEDEPOT

HOMEDEPOT HUGGER II RD4130AH-BN User manual

HOMEDEPOT

HOMEDEPOT F3501 Manual

HOMEDEPOT

HOMEDEPOT Merra CFN-1054 User manual

HOMEDEPOT

HOMEDEPOT WINDWARD IV 99966 User manual

HOMEDEPOT

HOMEDEPOT Merra CFN-1032 User manual

HOMEDEPOT

HOMEDEPOT EF200S-52 User manual

HOMEDEPOT

HOMEDEPOT CFN-1053 User manual

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual