Holbach LKS 30 User manual
Operating Manual
Transverse Adapter:
Outer diameter of inlet pipe: 50 mm
Inner diameter of inlet pipe: 46 mm
Pipe length (lR) without thread: 123 mm
Adapter height (hQ): 55 mm
Adapter diameter (dQ): 64 mm
Connection thread: R 3/4 Inch
Flow tolerances achievable with MBASS30:
when loading one PU foam cylinder ± 6 %
when loading two PU foam cylinders ± 8 %
Weight:
Transverse adapter ith inlet pipe: 675 g
Inlet pipe only: 155 g
Material: Anodized aluminum and POM
Article No.: 02-160
Inlet nozzles:
Total length (lD): 70 mm
Length when inserted (lA): 40 mm
Outer diameter (dD): 50 mm
Weight depending on nozzle diameter: 100 ~ 130 g
Material: POM (Polyoxymethylene)
Article No.: see table on page 3
Note: ubject to technical changes
Please do also consult the operating manuals of LKS 30 and
LKS100 and of the used air-conveying devices.
lR
dQ
hQ
dD
lD
lA
R 3/4 Inch
Transverse Adapter and Inlet Nozzles
for Air Samplers LKS 30 / LKS100
Adapter head Inlet Pipe Inlet Nozzle
Umweltanalytik Holbach GmbH
Sperberweg 3 D-66687 Wadern Internet: www.holbach.biz
eMail: in o@holbach.biz
Phone: 06874 / 18 22 77
Tele ax: 06874 / 18 22 78
Transverse Adapter and Inlet Nozzles
Technical Data
Issued: 04/2017
Inlet Nozzles
For isokinetic microbiological air samplings in external air flows, e.g. in air
ducts, inlet nozzles are available to adapt the nominal flow rate of the sam-
pling head to the one of the sample air.
The flow rate of the sample air has to be measured with a flow meter to
determine the required inlet nozzle from the table above.
The cleaned inlet nozzle is mounted on the inlet pipe of the transverse
adapter. The sealing is provided by an O-ring on the shaft of the inlet noz-
zle. When using MBASS30 as air-conveying device, make sure that the
outgoing air is flowing in the same direction as the sample air.
3
Applications
The transverse adapter is an optional accessory for the air sampling
heads LKS 30 and LKS100 and allows to draw in the sample air hor-
izontally. Additionally, isokinetic microbiological air samplings and
the loading of PU foam cylinders for chemical air samplings are
possible. The transverse adapter is used instead of the top part of
the air sampling head.
Components
The transverse adapter consists of the adapter head and the inlet pipe. The
inlet pipe gets screwed into the adapter head and can be unmounted for
cleaning. Only screw on the transverse adapter hand-tight. The sealing is
provided by a gasket on the pipe.
Loading of PU Foam Cylinders
PU foam cylinders with a diameter of 50 mm and a length of 50 to
70 mm can be loaded for chemical air samplings. Up to two PU
foam cylinders can be inserted behind each other in the pipe. When
operating with MBASS30, 300 liters of sample air should be drawn prior
to the sampling without a PU foam cylinder for acclimation. The sampling
procedure is described in the relevant guidelines (e.g. DIN I O 16000 parts
12 and 13).
Remark hen using the air sampling head LKS100:
The air sampling head LKS100 has a much lower air
resistance than the LKS 30 when operating at
30 l/min to load o PU foam cylinder. Depending on
the resistance of the PU foam cylinder, this may lead
to the error message ”No sampler active”. By placing
the included 55 mm circular filter onto the jet plate,
the air resistance of LKS100 can be adjusted.
Remarks hen using MBASS30 as air-conveying device:
The usage of a binderless glass fiber filter is not possible due to its high flow
resistance. Manual checking of the air flow before and after the sampling,
as required by some guidelines, is not possible.
Inlet Nozzle
No.
Flow with
LKS 30
Flow with
LKS100 Article No.
1 - 3 m/s 02-171
2 1,5 m/s 5 m/s 02-172
3 2 m/s 7 m/s 02-173
4 3 m/s 10 m/s 02-174
5 5 m/s 16 m/s 02-175
6 7 m/s - 02-176
ample air flow
ampling in external air flow with transverse adapter and inlet nozzle
Transverse Adapter and Inlet Nozzles
Operating Manual for Transverse Adapter for Air Sampling Heads
2
The Transverse Adapter
Transverse Adapter and Inlet Nozzles
Operating Manual for Transverse Adapter for Air Sampling Heads
Isokinetic Microbiological Air Samplings
This manual suits for next models
1
Other Holbach Laboratory Equipment manuals
Popular Laboratory Equipment manuals by other brands
Agilent Technologies
Agilent Technologies 5800 ICP-OES user guide
Endress+Hauser
Endress+Hauser Cleanfit CPA875 operating instructions
NI
NI PXI-5422 CALIBRATION PROCEDURE
Collomix
Collomix Aqix operating instructions
SPEX SamplePrep
SPEX SamplePrep 6875 Freezer/Mill Series operating manual
Ocean Insight
Ocean Insight FLAME-NIR+ Installation and operation manual
Parker
Parker ALIGN-MG-NA Installation, operation and maintenance manual
BD
BD 644787 user guide
DENTAURUM
DENTAURUM Compact Megaplus Instructions for use
Biuged Laboratory Instruments
Biuged Laboratory Instruments BGD 626 instruction manual
VWR
VWR SAS Super IAQ instruction manual
illumina
illumina MiSeqDx reference guide