Hipcam Doorbell User manual
1
Importer:
TJM Imports B.V.
Zompstraat 8
8102HX Raalte
The Netherlands
www.tjmsupplies.nl
Copyright © 2019 TJM Imports B.V. All rights reserved.
2
Design of the Hipcam Doorbell
DC 5V power connection
(doorbell back)
Microphone
LED status light
IR LEDs
Wide angle lens
Light sensor
LCD touch screen Speaker
What’s in the box:
1x Hipcam video doorbell
1x Wireless doorbell chime
1x mounting materials
1x Manual
3
Doorbell installation
Locate your fuse box and turn the power o.
Ring your doorbell to double check that the
power is o.
1.
2.
The Hipcam Doorbell works with an output of
12-24v. If in doubt on your power supply output,
please consult with a specialist.
Installation with home chime
Installation with Hipcam chime page 8
Remove the front cover of your current
doorbell. Conrm the wires have an output
of 12-24v.
Disconnect the two wires connected to your
current doorbell ( A and B ) and x them to
the wall with a tape so they do not fall inside
the electrical conduit.
3.
4.
Front Back
Your current doorbell
Chime box
Wires to chime box (12-24v)
4
Remove the backplate from your Hipcam
Doorbell by pushing the pin provided in the
box into the hole located at the bottom of
the unit.
5.
Backplate Doorbell
You might need to drill new holes on the
wall. You can do this by using the drill bit and
the plastic dowels included in the box.
Screw the backplate to the wall. You may
want to add the supplementary wall plate
between the wall and the backplate.
6.
7.
Front Back
Supplementary wall plate
Backplate
Wires coming
from the chime
box (must be
12-24v)
Locate your doorbell´s chime box. It should
look something like this:
8.
5
Remove the cover of your chime box. The
connection should look something like this:
9.
AC power source (110/220v)
12-24v
12-24v
Transformer
12-24v
Chime
Backplate
Connect the black and red wires provided in
the box to Hipcam Chime.
Insert one of the wires (the color is
indistinct) into hole 2 while pressing into
hole 1 with the pin provided in the box.
Insert the other wire into hole 4 while
pressing into hole 3 with the pin provided
in the box
Check both wires are tightly adjusted into the
holes by pulling them gently.
10.
11.
Pairing hole
Pairing LED
Wires provided in the box
Hipcam chime
6
Disconnect the wire from the TRANS terminal
on the chime box and connect it to the FRONT
terminal (A).
11.
Before After
AC stroom power source (110/220v) AC stroom power source (110/220v)
12-24v
12-24v 12-24v
12-24v
12-24v 12-24v
Chime box Chime box
Wire to your
doorway
Wire to your
doorway
Wire to your
doorway
Wire to your
doorway
Connect one of the wires from HIPCAM Chime
to the TRANS terminal on the chime box (A).
Connect the other wire from HIPCAM Chime
to the wired terminal on the transformer that
connects with your doorway (B).
12.
13.
Chime box
AC stroom power source (110/220v)
Wire to your
doorway
Transformer
Transformer
Transformer
Hipcam chime
Backplate
7
Connect the wire that comes from the trans-
former to your Hipcam Doorbell. Right or left is
indistinct (A)
Connect the wire that comes from the front
terminal in your chime box to your HIPCAM
Doorbell (B)Hipcam deurbel (B).
14.
15.
Backplate
Doorbell
Chime
Assemble Hipcam Doorbell to the backplate
screwed to the wall.
Go to your fuse box and turn the power on.
Hipcam Doorbell should turn on automatically.
If this does not happen, check the wire
connection on the chime box and that your
transformer has an output of 12-24v. Otherwise
you will need to upgrade the voltage of your
connection.
The Hipcam doorbell is now ready to pair with
your smartwatch. Read more about this on
page 10.
16.
17.
18.
19.
8
To install the Hipcam chime you can follow
the rst 7 steps of the installation with home
chime (pages 3 and 4).
Don’t forget to remove the power from the
doorbell!
Connect the wire that comes from the
transformer to your Hipcam Doorbell. Right
or left is indistinct (A).
Connect the wire that comes from the front
terminal in your chime box to your Hipcam
Doorbell (B).
1.
2.
3.
Installation with Hipcam chime
Backplate
Doorbell
Wires to your
doorway
Assemble Hipcam Doorbell to the backplate
screwed to the wall.
Open Hipcam Chime (Press the chime´s body
a little bit to take out the lid). Connect the USB
port to Hipcam Plug.
Connect HIPCAM Plug to the socket on the wall.
4.
5.
6.
9
Go to your Fuse box and turn the power on.
Hipcam Doorbell should turn on automatically.
If this does not happen, check the wire
connection on the chime box and that your
transformer has an output of 12-24v. Otherwise
you will need to upgrade the voltage of your
connection
The Hipcam doorbell is now ready to pair with
your smartwatch. Read more about this on
page 10.
7.
8.
9.
10
Get started
Download and Install “Hipcam The Smart
Home Security Ecosystem” App on your
smartphone from Google Play or App Store.
Make sure the Hipcam camera is switched on.
Create a new Hipcam user:
Press “Sign Up”.
Insert your desired e-mail address and
password (your password must include
at least one symbol and be eight or more
characters long).
Conrm your password.
Press the “Create” button, you will then
receive a Hipcam activation link to your
e-mail account.
Open your email account in your smartphone.
Click on the activation link and it will take you
to the Hipcam App prole creation page.
Add your prefered Prole Photo (Optional).
Fill in your name details and press “Set
Prole”.
Click on “Generate QR Code”.
Select your prefered language and press next.
Insert your Wi-Fi password (must be a 2.4
Ghz frequency) and press “Conrm”. The QR
Code scanning animation tutorial will appear.
Click on “Ok” to continue.
1.
2.
3,
4.
5.
6.
Table of contents
Other Hipcam Accessories manuals
