Hinkley 1609 User manual
assembly instructions
Item no. 1609
start here
H I N K L E Y L I G H T I N G 33000 Pin Oak Parkway Avon Lake, OH 44012 800.446.5539 / 440.653.5500 hinkleylighting.com
REVISION 1
assembly instructions
1609
H I N K L E Y L I G H T I N G 33000 Pin Oak Parkway Avon Lake, OH 44012 800.446.5539 / 440.653.5500 hinkleylighting.com
REVISION 1
start here
Drawing 1
I.S.200 caulking instructions
I.S. 200
8.12.10
caulking gun
1. After securing fixture to the wall it is recommended that the gap between the wall
and fixture backplate be sealed with any good quality waterproof caulk or silicone sealant.
(NOT INCLUDED)
Backplate
bead of
caulk to
seal gap
See Drawing 1.
HINKLEY LIGHTING 33000 Pin Oak Parkway Avon Lake, OH 44012 800.446.5539 / 440.653.5500 hinkleylighting.com
1. After securing fixture in place it is recommended that the gap between the mounting top
and fixture base be sealed with any good quality waterproof caulk or silicone sealant.
(NOT INCLUDED). It is also recommended that a small bead of caulk or sealant be put under
the ball knobs used to mount fixture.
caulking gun
ball
knob
caulking
See Drawing 2.
Drawing 2
I.S. 18 wiring grounding instructions
SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (I.S. 18)
AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING
INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED
ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS.
wiring instructions
Indoor Fixtures
1. Connect positive supply wire (A) (typically black or the smooth, unmarked
side of the two-conductor cord) to positive fixture lead (B) with appropriately
sized twist on connector - see Drawings 1 or 2.
2. Connect negative supply wire (C) (typically white or the ribbed, marked
side of the two-conductor cord) to negative fixture lead (D).
3. Please refer to the grounding instructions below to complete all
electrical connections.
Outdoor Fixtures
1. Connect positive supply wire (A) (typically black or the smooth unmarked
side of the two-conductor cord) to positive fixture lead (B) with appropriately
sized twist on connector - see Drawings 2 or 3.
2. Connect negative supply wire (C) (typically white or the ribbed, marked
side of the two-conductor cord) to negative fixture lead (D).
3. Cover open end of connectors with silicone sealant to form a watertight seal.
• If installing a wall mount fixture, use caulk to seal gaps between the fixture
mounting plate (backplate) and the wall. This will help prevent water from
entering the outlet box. If the wall surface is lap siding, use caulk and a
fixture mounting platform specially.
4. Please refer to the grounding instructions below to complete all
electrical connections.
grounding instructions
Flush Mount Fixtures
For positive grounding in a 3-wire electrical system, fasten the fixture ground
wire (E) (typically copper or green plastic coated) to the fixture mounting strap (1)
with the ground screw (2) - see Drawing 1.
Note: On straps for screw supported fixtures, first install the two mounting screws in strap.
Any remaining tapped hole may be used for the ground screw.
Chain Hung Fixtures
Loop fixture ground wire (E) (typically copper or green plastic coated) under the
head of the ground screw (2) on fixture mounting strap (1) and connect to the
loose end of the fixture ground wire directly to the ground wire of the building
system with appropriately sized twist-on connectors - see Drawing 2.
Post-Mount Fixtures
Connect fixture ground wire (E) (typically copper or green plastic coated) to power
supply ground with appropriately sized twist-on connector inside post. Cover open
end of connector with silicone sealant to form a watertight seal - see Drawing 3.
Drawing 1 - Flush Mount
Drawing 2 - Chain Hung
supply wire
fixture leads
twist-on
connectors
Drawing 3 - Post-Mount
twist-on
connectors
1
A CC
BD
supply wire
fixture leads
A C
BD
1
2
supply wire
fixture leads
A C
BD
twist-on
connectors
E
2
E
E
E
E
E
E
I.S. 18
H I N K L E Y L I G H T I N G 33000 Pin Oak Parkway Avon Lake, OH 44012 800.446.5539 / 440.653.5500 hinkleylighting.com
Table of contents
Other Hinkley Light Fixture manuals
Popular Light Fixture manuals by other brands
Emos
Emos CLASSIC ZY1431T manual
Westinghouse
Westinghouse Outdoor Lighting Fixture owner's manual
Hedler
Hedler C 12 silent Operation manual
Blizzard Lighting
Blizzard Lighting Puck: CSI manual
Energetic Lighting
Energetic Lighting ELYSL-5004 Series installation instructions
Lightmaxx
Lightmaxx Shaft 5R user manual
Cooper Lighting
Cooper Lighting Halo L3232E Specification sheet
Stageline
Stageline ODW-2410RGBW instruction manual
Light Sky
Light Sky Tornado Series user manual
Lightolier
Lightolier Paralyte 2424 PLA2G9LS26U specification
Lightolier
Lightolier Lytespan 83ED17S specification
Lightolier
Lightolier Calculite CS8226 specification