Heta SCAN-LINE SOLID C User manual

ECODESIGN READY

OPERATING AND INSTALLATION

INSTRUCTIONS

SCAN-LINE SOLID C

THE SCAN-LINE SOLID C IS EXEMPT FOR USE

IN SMOKE CONTROL AREAS WHEN BURNING DRY WOOD

DANISH DESIGN . DANISH QUALITY . DANISH PRODUCTION

www.heta.dk

Congratulations on your new stove. We are sure that you will be happy with your in-

vestment, especially if you follow the advice and instructions we have put together in

these operating instructions.

The Scan-Line Solid C have been approved according to the EN 13240, NS 3058/3059

and the Scan-Line Solid C is modiﬁed so that they are also recommended as exempt

for use within smoke control areas (SCA) throughout the UK (see clean air act Appen-

dix A). of the air supply regulation so that it can`t be closed completely.

Heta A/S

Jupitervej 22,

DK-7620 Lemvig

Phone: +45 9663 0600

E-mail: [email protected]

Heta is a registered

trademark of Heta A/S

18.05.2022

0037-1514 Version 2.4

Printed in Denmark

Subject to printing errors

and changes.

Operating Instructions Contents

Before installation ....................................................... 4-5

Accessory Parts.............................................................. 6

1. Operating instructions .................................................... 7

1.1 Before using.................................................................... 7

1.2 First ﬁring ........................................................................ 7

1.3 Regulating the airﬂow .................................................... 7

1.4 Lighting the stove ........................................................... 7

1.5 Refueling ......................................................................... 7

1.6 Reduced burning ............................................................ 8

1.7 Risk of explosion............................................................. 8

1.8 Emptying the ash ............................................................ 8

1.9 Draft conditions in the chimney ...................................... 8

1.10 Fuel ................................................................................. 9

1.11 Operational problems ................................................... 10

1.12 Chimney ﬁres ................................................................ 10

1.13 Maintenance ................................................................. 10

1.14 Cleaning the glass ........................................................ 10

1.15 Lubricate the moving parts........................................... 10

1.16 Diagram for the maintenance ...................................... 11

1.17 Troubleshooting............................................................ 12

1.18 Cleaning/Replacing bricks after chimney sweeping..... 13

1.19 Stove data table EN 13240........................................... 14

1.20 Garantee ....................................................................... 14

1.21 Parts......................................................................... 15-16

2. Installation Instructions................................................. 17

8120-0000-DK 8120-0100-DK

8120-0200-DK 8120-0200-DK

DOP-Prestige Indsats 2237-2016

Heta A/S

Jupitervej 22 . DK-7620 Lemvig . Denmark

Produktionsår: 2016

DS/EN 13229/A2:2004/NS 3058/3059

Produkt beskrivelse Serie nr.:

Brændsel: Træ

Ydelse nominel: 8 kW

Røggas temperatur: 3120C

Middel CO emission: 0,085%

Middel CO emission i mg/Nm3: 1063 mg/Nm3

Støv: 27 mg/Nm3

Virkningsgrad: 79%

Nox (mg/Nm3): 109 mg/Nm3

Støv (NS 3058/3059) samlet vægtet partikelemission: 2,15 g/kg

OGC ved 13% O2 (CEN/TS 15883): 81 mgC/Nm3

Afstand til brændbart uden sideglas: 400 mm

Afstand til brændbart med sideglas: 550 mm

Afstand til brændbart - front: 1100 mm

For opbygning i øvrigt - se installationsvejledning.

Indsatsen må tilsluttes røggas samleledning.

Ovnen er egnet til intermitterende brug.

Anvend kun anbefalet brændsel.

Følg fabrikantens brugervejledning.

Prestige Indsats

Lukket ildsted

For inddbygning

BETJ ENING S- OG

OPST ILLIN GSVEJ LEDNING

SCAN -LINE S OLID C

DANSK DES IGN . D ANSK KVALITET . DA NSK PRODUKTION

www.heta.d k

Operating /

Instruction manual

Heta glove

CHR list

Standard V1,30

Data plate

Sealant

Repair mortar

Flue collar

1525-0031

Handle

2 x 1013-1006

4 x M6x10

Bolt 0008-1117

13 x M6x8

Bolt 0008-0035

13 x M6x25

Distance brackets

0008-1807

Top panel

1026-0149

Base

4018-0050

BEFORE INSTALLATION

Heta wood stoves are quality products, therefore, your ﬁrst impression is very important! We have

a good logistics network, which transports Heta products with great care for our dealers. Neverthe-

less, when in transport or handling, damage of the often-heavy stoves can occur. It is important that

upon receipt check your Heta product completely and report any damage or defects to your dealer.

The packaging must be disposed of as follows:

Wood is untreated and able to burn in the stove.

Plastic and cardboard you can drop off at your local recycling center.

With your new wood stove you should ﬁnd the following:

NB!

Heat shield must be installed.

See page 24.

NB!

Heat shield must be installed.

See page 23.

Required tools are not supplied.

Concrete

element

1 x 0023-2507

1 x 0023-2508

1 x 0023-2509

Heat shield

1 x 1022-0087

2 x 1022-0090

1 x 1022-0091

Adjustment

device

2 x 1513-0151

1 right

1 left

Graphite spray

for lubrication

Solid C High

Top

Concrete

element

1 x 0023-2509

Heat shield

2 x 1022-0090

1 x 1022-0091

1 x 1022-0094

13 x 0008-1807

13 x 0008-0035

External air from

behind

1 x 0032-0027

Accessory Parts

Akkumulation

1 x 0023-0237

2 x 0023-0237

3 x 0023-0237

4 x 0023-0237

(Solid C High)

Solid C

External air from behind (1324 mm)

5032-0082

1 x 1522-0009

3 x 0008-1720 3,9x14

screw

- 1011-0275

- 1011-0276

1511-0032 -

4 x 0008-1720 3,9x14

5 x 0008-2301 M4x8

External air from below, complete

1511-0033

90o Flue pipe

1 x 0050-0514

Solid High

External air from behind (1824 mm)

5032-0092

1 x 1522-0009

3 x 0008-1720 3,9x14 screw

Flue pipe 1 x 1021-4087

90o Flue pipe

1 x 0050-0514

1. OPERATING INSTRUCTIONS

Bafﬂe plate

Handle

- combustion air

Door

Firebox

Closed Open Start-up air

1.1 Before using

Before the wood stove is used make sure

required installation conditions, are met. See

page 20-21.

1.2 First ﬁring

The stove paint is fully cured from the factory,

but a minor unpleasant odour could still arise.

1.3 Regulating the air ﬂow

A handle below the door regulates the stoves

combustion air.

For start-up air hold the handle to the far right.

The handle will go back into its open position

when the air controll handle is released.

See ﬁg. 2.

The Scan-Line Solid C stoves are designed and

tested to burn extremely cleanly with very little

smoke discharge and are exempt for use in

smoke control areas throughout the UK when

burning dry wood logs. To comply, a permanent

stop is ﬁtted to ensure that the air control slider

cannot be closed beyond (percentage of air as

per test) of its fully open position. A permanent

amount of air will therefore enter the ﬁrebox to

feed the ﬁre producing negligible amounts of

smoke and unburnt hydrocarbons. The applian-

ces will only be considered as an exempt appli-

ance if this stop is in place.

1.4 Lighting the stove

Place two pieces of wood on the bottom. Stack

kindling on top in layers with air between. Set-

ting ﬁre starter (bag, brick, parafﬁn) on the top,

now you are ready to light the fuel. The ﬂames

must work from the top down.

The use of lighter ﬂuid, oils or any

liquid fuels is strictly forbidden

from use in a wood stove.

Fully open the combustion air and leave the

door ajar (about 1 cm open).

Once the ﬁre is established and the chimney is

hot (after about 3-5 minutes) closed door and

regulate the air into operating position. We re-

commend, all of the ﬁrst fuel is burned with the

combustion air fully open in the operating po-

sition. This ensures the stove and chimney are

thoroughly heated.

Startup/Lighting

Scan the code and select a language.

1.5 Refueling

Refueling of your stove should be done while

there is still a good layer of embers. Distribute

the embers with the majority of them to the front.

Place pieces of wood equivalent to about 1 kg

on top of the embers perpendicular to the door.

Now open the combustion air completely. If the

stove and/or chimney cools down too much, it

may be necessary to use the start-up air and

possibly have the door ajar.

Maximum

wood ﬁlling

Vermiculite

(stone)

come from the tree, when it is becomes glowing

charcoal.

If you are looking for less heat out-put, achieve

this by fueling with smaller volumes of wood and

a lower operating air. You may not completely

close the operating air during ﬁring.

Be aware that the stove will naturally soot if the

operating air is too low. This is not good for the

environment. There is also a risk for the glass,

he chimney and other parts will become sooted.

By a combination of the above and possibly

burning damp wood. Can lead to high levels of

soot that it becomes sticky. Causing the sealing

of the door to tear off when opening the door

the next day.

1.7 Explosion!!!

It is very important never to leave

The stove after start up or refueling,

before the ﬁre is established.

(Typically 1 to 3 minutes)

Explosion can occur if ﬁlled with too much fuel

in the stove, the production of large volumes

of gas, which can explode if the air supply be-

comes too low.

1.8 Emptying the ash

Be careful not to damage the vermiculite when

the removing the ash.

Be careful when emptying the

ashes out. There can be hot

embers left for a long time.

Never empty ash into a combusti-

ble container.

It is an advantage for the next ﬁring to leave a

layer of ash lying in the bottom of the ﬁrebox.

Warning!

One must always use cation around

the stove seen, as it gets very warm

during use. (In excess of 90° C).

Children should avoid contact with the stove.

Setting up a fence if you have small children may

be necessary.

Do not place ﬂammable objects like drying racks,

furniture, curtains too close to the stove.

The wood will then ignite within a very short time

(Typically 1 to 3 minutes). Once the fuel is Ignited

Close the door and regulate the air back to ope-

rating air. When the ﬁre is well established, you

can now regulate the operating air to the desired

combustion level.

Nominal heat out-put is 8 KW, equivalent to the

operating air at about 40% open, requiring re

fueling after approximately 50 min.

Ensure when refueling that the wood is not too

close, it will cause poorer combustion, less heat

out-put and lower efﬁciency.

The fuel load, must be maintained below the top

series of air holes and within the outer vent in

each side. Fig. 5

When refueling be careful to place

the fuel into the combustion

cham-

ber gently, (use the provided glo-

ve). By not doing so you risk crack-

ing or breaking the vermiculite.

If there is reduced draft in the chimney, we re-

commend opening a window at stoking. This will

give better ventilation to the room and more oxy-

gen for combustion.

1.6 Reduced burning

The stove is, designed for intermittent use.

It is important to maintain the layer of hot em-

bers. Lower heat out-put occurs when no ﬂames

Combustion

air

Combustion

air

1.9 Draft conditions

and the chimney

Poor draft will not allow the stove to burn, as it

should. The glass can soot, requires cleaning of

the chimney more often, smoke can escape out

when the door is open and it gives poor fuel ef-

ﬁciency. Leading to unnecessary polluting of the

environment.

Good draft will allow the stove to achieve op-

timal combustion and the highest possible ef-

ﬁciency. Heta wood stoves are constructed so

that it itself provides an optimal blend of com-

bustion air. This provides a high efﬁciency/heat,

clean glass and low environmental impact.

Minimum chimney draft

for Prestige insert is 10

PA.

It is the draft that the stove has been tested

and approved on. The minimum draft is neces-

sary to provide clean burning, beautiful ﬂame

picture, as well as achieving the rated efﬁciency.

There is a risk of smoke escaping into the room

if the door is opened during vigorous ﬁring, or if

there is a lack of air supply to the room, for ex. if

an extraction fan is in use.

Flue gas temperature at the rated output is 312°C

relative to 20°C. Flue gas ﬂow is 6,3 g / sec.

The chimney height and diameter, as well as

the temperature difference between the ﬂue gas

and outside temperature generates the chimney

draft. Chimney insulation is therefore important

as new efﬁcient stoves create lower ﬂue tempe-

ratures. Wind and weather conditions also in-

ﬂuence draft, in some cases it may be disad-

vantageous wind direction, combined with the

position of the chimney can cause negative draft

(it blows through the chimney), causing smoke

escape from the stove.

Before using after a long period of inactivity,

check that the chimney is free for any blocka-

ges. (soot build-up, bird nests, leaves etc.).

Reduced draft can occur when:

• The temperature difference is too small

between smoke gasses and outdoor

• To short of a chimney• The outside temperature is high, and indoor temperature is low f. ex. in summer

• False air in the chimney• Chimney is blocked• Air tight house (lack of combustion air supply)• Poorly placed chimney for the surroundings, for ex. the ridge and trees may cause

turbulence.

Good draft occurs when:

• The difference in temperature in the chimney

(warmer) and outside temperature (colder)

• It is clear weather• The chimney has the right height min 4 metersabove the stove, and clear of the roof ridge

1.10 Fuel

Your new stove is EN approved for ﬁring with

wood fuel. You must therefore only burn clean,

dry wood in your stove. Never use your stove

to burn driftwood, as this may contain a lot of

salt which can damage both the stove and the

chimney. Similarly, you must not ﬁre your stove

with refuse, painted wood, pressure-impregna-

ted wood or chipboard, as these materials can

emit poisonous fumes and smoke.

Correct ﬁring using well seasoned wood pro-

vides optimal heat output and maximum efﬁ-

ciency. At the same time, correct ﬁring prevents

environmental damage in the form of smoke

emissions and reduces the risk of chimney ﬁres.

If the wood is damp and inadequately seasoned,

a large proportion of the energy in the fuel will

be used to vaporize the water, and this will all

disappear up the chimney. Thus, it is important

to use dry, well seasoned wood, i.e. wood with a

moisture content of less than 20 %. Achieve this

by storing the wood for 1–2 years before use.

Pieces of ﬁrewood with a diameter of more than

10 cm should be split before before storing. The

pieces of ﬁrewood should be of an appropriate

length (approx. 19-25 cm) so that they can lie

ﬂat on the bed of embers.

If you store your wood outdoors, it is best to

cover it.

Examples of fuel values

for different woods and their typical densities

per cubic meter, speciﬁed for 100% wood with

a moisture content of 18%.

Wood kg/m3Wood kg/m3

Beech 710 Willow 560

Oak 700 Alder 540

Ash 700 Scotch pine 520

Elm 690 Larch 520

Maple 660 Lime 510

Birch 620 Spruce 450

Mountain pine 600 Poplar 450

It is advised not to use oil-containing woods

like teak tree and mahogany, as this can cau-

se damage to the glass.

Heating value in wood

You have to use about 2.4 kg normal wood to

replace one litre of heating oil. All woods have

almost the same heating value per kg, which is

about 5.27 kW/hour for absolute dry wood.

Wood with a moistness of 18% has a efﬁciency

of about 4.18 kW / hour per kg, and one litre

heating oil contains about 10 kW / hour.

CO2release

At combustion 1000 litres of heating oil forms

3.171 tons CO2. As wood is a CO2neutral heat/

energy source, you save the environment about

1.3 kg CO2every time you have used 1 kg nor-

mal

wood.

1.11 Operational problems

The chimney must be swept at least once a

year, we recommend the use of a NACS (natio-

nal association of chimney sweeps) registered

chimney sweep.

In the event of smoke or malodorous fumes are

being produced, you must ﬁrst check to see

whether the chimney is blocked.

The chimney must, of course, always provide

the minimum draft necessary to ensure that it

possible to regulate the ﬁre. Please note, how-

ever, that chimney draft is dependent on the wea-

ther conditions. In high winds, the draft can be-

come so powerful that it may be necessary to ﬁt a

damper in the ﬂue gas pipe to regulate the draft.

When cleaning the chimney, soot and other

deposits may come to fall on the bafﬂe plate,

remove and clean it. In cases where the wood

burns too quickly, this may be due to excessive

chimney draft. You should also check to make

sure that the door seal and ash pan seal is intact

and correctly ﬁtting.

If the stove it generating too little heat, this may

be because you are ﬁring with wet wood. In this

case, much of the heating energy is used to dry

the wood, resulting in poor efﬁciency, poten-

tially damaging the vermiculite and an increased

risk of soot deposits in the chimney.

1.12 Chimney ﬁre

In case of a chimney ﬁre, which often results from

incorrect operation/maintenance or prolonged

use of damp wood, close the door and the air

supply completely, to help slow/smother the ﬁre.

Call the ﬁre department.

The stove and chiminey must be inspected be-

fore use again.

1.13 Maintenance

The surface of the stove is treated with a heat-

resistant paint. The stove should be cleaned

with a damp cloth.

Any damage to the surface in the form of chips

or scratches can be repaired using touch-up

paint, which is available in spray cans.

1.14 Cleaning the glass

Incorrect ﬁring, for example using wet wood,

can result in the viewing window becoming

covered in soot. This soot can be easily and

effectively removed by using proprietary stove

glass cleaner.

1.15 Lubricate the moving parts of

the stove with graphite spray

Before using graphite spray, you

should cover the exposed sur-

faces so that lubricants are ap-

plied only to the moving parts.

Always test the graphite spray on a hidden

surface to make sure the can is working as

intended.

Graphite spray should only be used on a

cold stove.

Other manuals for SCAN-LINE SOLID C

Table of contents

Other Heta Stove manuals

Heta

Heta CLEAN BURN SL 500 Series User manual

Heta

Heta INSPIRE 40 User manual

Heta

Heta Scan-line 8 User manual

Heta

Heta SCAN-LINE95 User manual

Heta

Heta SCAN-LINE GREEN 300 User manual

Heta

Heta SCAN-LINE 40 User manual

Heta

Heta Scan-Line 900 Series User manual

Heta

Heta Icon-line Moderna Series User manual

Heta

Heta SCAN-LINE 550 User manual

Heta

Heta Scan-line 8 User manual

Heta

Heta SCAN-LIINE 80 XL User manual

Heta

Heta SCAN-LINE 550 User manual

Heta

Heta Ambition 5 User manual

Heta

Heta Scan-Line 70 User manual

Heta

Heta SCAN-LINE GREEN 300 User manual

Heta

Heta SCAN-LINE 10 User manual

Heta

Heta Scan-Line 1000 User manual

Heta

Heta Vista User manual

Heta

Heta Scan-Line 800 Series User manual

Heta

Heta SCAN-LINE 80 User manual

Heta

Heta Scan-Line Tour 10 User manual

Heta

Heta vision III User manual

Heta

Heta SCAN-LINE AQUA User manual

Heta

Heta GREEN200 User manual

Popular Stove manuals by other brands

Arada

Arada Cassette Stove installation guide

Parmco

Parmco FS 600 Installation and operating instructions

MCZ

MCZ SUITE AIR 10 M2 installation guide

HearthStone

HearthStone Stowe DV 8321 Owner's manual & installation guide

Cattara

Cattara FAMILY manual

Stanley

Stanley Argon F500 OVAL Installation and operating instructions

Avalon

Avalon B-VENT instructions

Nordpeis

Nordpeis Vega user manual

Exquisit

Exquisit EKC601-5 Instructions for use and installation

Stanley

Stanley Oisin Oil MK II Installation and operation instruction

Thermocet

Thermocet Brookfield S/CC Operating and installation instructions

HASE

HASE delhi operating instructions

Vermont Castings

Vermont Castings Intrepid 2 User instructions

Italiana Camini

Italiana Camini CLASSICA Installation, use and maintenance

Avalon

Avalon Vashon Avanti DVS FS manual

Spartherm

Spartherm ambiente a1 Installation and operating manual

Dimplex

Dimplex MCFSTV12AU manual

Warmlite

Warmlite WL46040 manual