HERMITAGE BATH 7151 Series User manual
Installation Manual
Manual de Instalación
For technical suppo contact
Para sopoe técnico, póngase en contacto con
58-60 pulgadas de ancho × 76 pulgadas de alto & 58-60 pulgadas de ancho × 60 pulgadas de alto
626-341-5763
http://www.homebandc.com/
Model Number/Número de modelo: 7151 Series
58-60 in. W × 76 in. H & 58-60 in. W × 60. H
Sliding Framed
Shower Door & Tub Door
Puea corrediza con
marco para ducha & puea para bañera.
Detalles del componente
Instrucciones previas a la instalación
21-28
29-36
19
20
Pasos de instalación para apeura izquierda
Pasos de instalación para apeura derecha
Component Details
Pre-Installation Guidelines
3-10
11-18
1
2
Steps for Left Handed Opening Installation
Steps for Right Handed Opening Installation
English
01
Español
02
TABLE OF
CONTENTS
Detailed Diagram of
Shower Door Components
1
FIXED PANEL (1 pcs)
WALL BRACKET (2 pcs)
COUNTERSUNK HEAD
ST3.5X35 (6 PCS)
COUNTERSUNK HEAD
ST4.8X38 (4 PCS)
WALL PLUG
(6 PCS)
6
WALL CHANNEL (1 pcs) HANDLE (1 pcs) BOTTOM TRACK (1 pcs) BOTTOM TRACK COVER
(1 pcs) DOOR GASKET (1 pcs) GAP GASKET (2 pcs)
DOOR PANEL (1 pcs) ROLLERS (2 pcs) GLASS HOLDERS (2 pcs) STOPPERS (2 pcs) BOTTOM GUIDE (1 pcs) RUNNING RAIL (1 pcs)
WALL PLUG
(4 PCS)
GLASS FIX NAIL
(2 PCS) WEDGE VINYL (2 PCS)
8
3/8" glass is
not matched
PARTS LIST.
Before You Sta
Required Tools
SILICONE
LEVEL PENCIL
DRILL MEASURE TAPE
SCREW DRIVERS HANDSAW SAFETY GLASSES
RUBBER MALLET DRILL BITS
2
Thank you for choosing our sliding shower door. We aim to provide you with the most satisfying
product and user experience. Please carefully read through this manual as it contains impoant
product information and step-by-step installation instructions. Failure to follow the instructions
may aect the product's warranty.
1.Before installation, please inspect the boxes for any damage caused during shipping. If any
pas are missing or defective, please contact our customer seice by email at info@lifeupinc.net
within 7 business days from the delive date. Please note that we will not provide free
replacements for damaged products or missing pas if you contact us more than 7 business days
after product installation. Feel free to reach out if you have any questions related to your
purchase order number.
2.Ensure that you consult your local building codes if you have any questions about installation
standards. Building and plumbing codes may va depending on your location.
3.Verify that the installation suace or level is strong enough to suppo the weight of the shower
door. Do not install it on plastic shower modules or dwall unless additional suppo is provided
behind the wall.
4.This shower door is quite heavy and should be installed by a professional.
1.Always wear safety glasses when cutting or drilling.
2.Unframed tempered glass should never come into contact with rigid suaces, as it may shatter.
Avoid touching the edge of the tempered glass panel with tools or any rigid object, and refrain
from placing the unframed tempered glass edge directly on the oor.
3.Do not t to cut tempered glass, as it will shatter.
Warnings
!
1/4"
5/16"
LEFT HAND ASSEMBLY
Install the rollers on the door.
Remove the rollers from the package and
install them on the door panel as shown in
the illustration. Secure them using a 5/32"
Hex key.
Shower Door Left Side Opening Installation Method
Follow the corresponding diagram below for instructions
STEP 1
3
STEP 2
Place the door panel inside your shower
room and position the wooden blocks under
the bottom as shown in the illustration.
Drill holes for the wall channel with a 1/4" drill bit.
Drill holes for the wall bracket with a 5/16" drill bit.
For dwall with a thickness greater than 3/8" to 1/2", please ensure the use of specied dwall
anchors for installation. For dwall with a thickness less than 3/8" to 1/2", please ensure that
you install the brackets on the stud.
STEP 4
4
Use a professional level and the provided positioning guide to determine the position of the
wall channel, as shown in the illustration.
STEP 3
Install the wall plugs.
STEP 5
Install the wall channel. Secure the wall channel using ST3.5x35 screws in the holes from the
previous steps.
Install the wall bracket. The wall bracket consists of two pas; now, remove the inner pa,
which is the bracket base, as shown in the pictures. The bracket base may tend to slide down on
the single mounting screw. So, once you have determined the appropriate height (ensuring that
there is a large enough gap at the bottom of the door for it to slide easily through the bottom
guide), disassemble it, mix up the epoxy putty, and apply some to the slotted hole above the
screw head on both bracket bases.
5
STEP 6
The bracket base
mounting hole might slip,
so you may need to use
epoxy or shims.
6
Measure and cut the Bottom Track.
Measure from one wall to the Wall Channel
at the bottom. Mark the Bottom Track at the
determined distance, then cut it from the
end. Smooth out the rough edges (being
careful to avoid damaging the nished
suaces). The cut Bottom Track should t
ush between the walls without the need
for hand pressure.
STEP 7 STEP 8
Drill holes for the Bottom Track with a
1/4" drill bit.
Install the wall plugs.
STEP 9 STEP 10
Install the Bottom Track. Secure the
Bottom Track using ST3.5x35 screws in the
holes as described in the previous steps.
7
Use caulk gun inject Clear Silicone Sealant
to the wall channel and bottom track.
NOTE:lf the glass is not 3/8", please
ignore this step.Please go ahead to the
next step.
STEP 11 STEP 12
Install the xed panel. Put the xed panel
into the Bottom track and the Wall channel.
If the glass is not 3/8" thick, cut the wedge
vinyl to the exact size of the xed panel
and inse them into the Wall Channel and
Bottom Track.
Measure and cut the Running Rail. Measure
from one wall to the other at the top of the
shower door opening. Mark the running rail
at the determined distance. Cut it from the
end and smooth out the rough edges where
the running rail was cut, taking care to avoid
damaging nished suaces. The cut running
rail should t ush between the walls without
the need for hand pressure.
STEP 13 STEP 14
Install the stoppers. Position the stoppers
on the running rail and secure them
temporarily in place. Do not fasten them;
fasten them after installing the xed panel
and glass panel.
Position the outer pa of the wall brackets
on the running rail. Secure them temporarily
in place.
Install some pas of glass holders on the
running rail as illustrated.
Only cut this side if it is necessa!
Fasten the running rail. Secure the outer pa of the wall bracket. Attach the running rail to the
xed panel using the glass holders. Secure them temporarily in place.
STEP 15
Install the bottom guide.
Use the positioner to determine the bottom guide's position as illustrated in step 1. Drill holes
with a Ø5/16" drill bit as shown in step 2. Fasten the bottom guide according to the holes from
the above steps using Ø5/16 wall plugs and ST4.8*38 screws, as illustrated in steps 3 and 4.
STEP 16
Please review the bottom. Position the black rubber pa to match the thickness
of the glass. This bottom comes in 4 dierent thicknesses. Ensure that the
thickness of the glass aligns with the corresponding black rubber pa. Fasten
the bottom guide as illustrated.
8
Fasten the running rail. Secure the outer pa of the wall bracket. Attach the running rail to the
xed panel using the glass holders. Secure them temporarily in place.
STEP 15
Install the bottom guide.
Use the positioner to determine the bottom guide's position as illustrated in step 1. Drill holes
with a Ø5/16" drill bit as shown in step 2. Fasten the bottom guide according to the holes from
the above steps using Ø8 wall plugs and ST4.8*38 screws, as illustrated in steps 3 and 4.
STEP 16
Please review the bottom. Position the black rubber pa to match the thickness
of the glass. This bottom comes in 4 dierent thicknesses. Ensure that the
thickness of the glass aligns with the corresponding black rubber pa. Fasten
the bottom guide as illustrated.
8
Table of contents
Languages:
Other HERMITAGE BATH Bathroom Fixture manuals
