Henkel Loctite RB10 User manual

EQUIPMENT

Operation Manual

LoctiteRB10 Rotary Dispense System

Part Number 1635546

Table of Contents

1Please Observe The Following 3

1.1 Emphasized Sections 3

1.2 For Your Safety

1.3 Inspection 3

1.4 Items Supplied 4

1.5 Features 4

2 Description 4

2.1 Control Panel 4

2.2 Integration Panel 5

3 Technical Data 5

4 Installation 6

5 Operation 7

5.1 Theory of Operation 7

5.2 Controller Set Up 8

5.3 Mounting Plate 10

5.4 Valve and Syringe Dispenser Integration 11

5.4.1 Light Cure, CA and VA10 Valves 11

5.4.2 Stationary Valves 11

5.4.3 Syringe or Cartridge Dispensing 12

5.5 Slide Adjustment 13

5.6 Reservoir Low Level Control 13

6 Troubleshooting 14

7 Care and Maintenance 14

8 Accessories 15

9 Wiring Schematic 15

10 Warranty 16

1 Please Observe The Following

1.1 Emphasized Sections

Warning!

Refers to safety regulations and requires safety measures that protect the operator or

other persons from injury or danger to life.

Caution!

Emphasizes what must be done or avoided so that the unit or other property is not

damaged.

Notice:

Gives recommendations for better handling of the unit during operation or

adjustment as well as for service activities.

1.2 For Your Safety

For safe and successful operation of the unit, read these instructions

completely. If the instructions are not observed, the manufacturer can assume no

responsibility.

Do not expose the connecting cable to heat, oil, or sharp edges.

Make sure the Unit stands stable and secure.

Use only original equipment replacement parts.

Always disconnect the power supply before servicing the unit.

Observe general safety regulations for the handling of chemicals such as

Loctite®adhesives and sealants. Observe the manufacturer’s instructions as stated

in the Material Safety Data Sheet (MSDS).

While under warranty, the unit may be repaired only by an authorized Loctite service

representative.

1.3 Unpacking and Inspection

Carefully unpack the Loctite®RB10 Rotary Dispense System and examine the

items contained in the carton. Inspect the unit for any damage that might have

occurred in transit. If such damage has occurred, notify the carrier immediately.

Claims for damage must be made by the consignee to the carrier and should be

reported to the manufacturer.

1.4 Items supplied

(1) Rotary Dispense System

(1) Foot Switch

(1) Power Supply with Cord

(1) Instruction Manual

1.5 Features

Integrated Solution –plug and play with Loctite valves, reservoirs, and

Syringe Systems

Digital Control of rotation, dispense start, dispense stop and delays

Adjustable height, position, angle of dispense, and advance slide speed

Reservoir low-level interface with cycle interruption and display message

Part position sensing allows orientation of adhesive bead start and end

Threaded and non threaded mounting holes for fixtures

Operator lockout for supervisory control of settings

Dispense valve and syringe mounting hardware available

2 Description

The Loctite®RB10 Rotary Dispense System is a fully integrated system used for

dispensing adhesives onto parts in a circular or arc pattern. It will control a syringe system,

cartridge, or dispense valve without requiring a separate valve controller. Internally

synchronized operation of an advancing slide, turntable, and dispense timer makes for easy

and repetitive placement of the adhesive. The set-up is simple, using only preset distance

and rotation speed adjustment. No complex programming required!

2.1 Control Panel (Front of Controller)

2.2 Integration Panel (Back of Controller)

3 Technical Data

Attribute Value

Dispense Pattern Circles or Arcs in a Circular Pattern

Slide Stroke 0 –2”(0 –50 mm)

Rotation Range 0 –999 Degrees

Rotation Speed 5 to 55 RPM

Maximum Part Height 12”(305 mm)

Maximum Part Diameter 18”(475 mm)

Maximum Part Weight 6 lbs (2.7 kg)

Width 12”(305 mm)

Depth 8¾”(222 mm)

Dimensions

Height 22”(559 mm) Minimum

25”(635 mm) Maximum

Weight 18.5 lb (8.4 kg)

Air Input*Clean, dry air not to exceed 125 psig (8.5 bar),

and filtered with a maximum of 50 micron

Power Supply: 110 –230 V / 50 –60 Hz

Internal: 24 VDC

* If the required air quality is not available, install a Loctite®filter regulator. In the US order a

5m filter using part number 985397. In Europe or Asia, order a 10 m filter using part

number 97120.

4 Installation

Before using the tool for the first time check it carefully for signs of external

damage. If any shipping damage is found DO NOT USE THE TOOL - return it to

your supplier immediately.

1. Assemblethe standtothemaincontrolunit byattaching theverticalmountingpole(the

longerbarsupplied)intotheverticalsupport bracketonthecontroloftheunit. Tighten

theM4 fromthesideofthesupport brackettosecure theverticalmountingpole.

2. Assemblethe slide assemblytothestand.

3. SecuretheslideassemblybytighteningtheM6 screwontheslide assemblybracket.

4. Connect the Cylinder Extend and Cylinder Retract Air hoses to the Cyl Extend

and Cyl Retract ports on the back of the unit.

5. Connect the Advance Slide Cable to the Advance Slice Limit Switch connector

of the back of the unit.

6. Plugthepower adapterwithcordintothe“24VDC”inputonthebackofthecontrollerand

intothewallsocket.

Notice: The power adapter has auto ranging power function that can be used

with either 110 or 220V and 50 or 60 Hz.

7. Connectthefootswitch,orPLCstartsignalcable,tothe“StartSwitchXS1”connectoron

thebackofthecontroller.

8. Connecttheairinputlineto theAirInputfittingusing6mmO.D.pneumatictubing(not

supplied).

9. Turn on the local airsupply. This must be a minimum of 80 psi anda maximum of 125

psi.

Warning! When the air is connected, the slide may retract. Be sure to keep

your hands and other objects clear of the slide before connecting the air.

Caution! Clean, dry, filtered air must be used. If it is not, the solenoids in the

controller will be fouled over time. If the required air quality is not achieved,

install a Loctite®filter regulator. In the US order a 5 m filter using Part Number

985397. In Europe or Asia, order a 10 m filter using Part Number 97120.

5 Operation

5.1 Theory of Operation

1. After turning on the unit, press the footswitch or ENTER button to activate the

system.

2. The advancing slide will start to extend and the rotary disc will start to rotate with

the preset speed.

3. The advancing slide will activate the proximity sensor when it reaches the preset

position.

4. The start of disc rotation, or the locator pin reaching the proximity sensor (in

homing mode), will trigger the rotation distance counter and the unit will start to

dispense for preset dispensing time. Use of the homing mode ensures that each

dispense start will be at the same point.

5. After the dispensing timer has reached the preset dispense time, the advancing slide

will retract and the rotary disc will be stopped.

6. The dispense start position “DS Position”determines how far the disc will rotate

before starting to dispense. This ensures the rotation has reached a constant speed

when dispense begins.

7. The “Off Delay”feature determines how long the disc will continue to rotate after

the dispense has stopped. This allows product remaining on the tip of the dispenser

to be transferred to the part after the dispense stops, prior to retracting.

8. The reservoir low level sensor setting disables the start signal and displays “Alarm:

RESERVOIR LOW LEVER.”The Low Level state can be manually overridden

allowing the system to cycle by pressing the ENTER button, however the alarm will

continue to be displayed and the system will not cycle using a footswitch or PLC.

5.2 Controller Set Up

Display

Step

Enter

To Unlock Press 1 & 3

Together For Three Seconds Toggle

Notice: Upon start-up, the system will be in operator lockout mode.

To unlock the controller, press 1 & 3 simultaneously for three seconds. To return to

operator lockout mode simply turn system off; all settings will be stored. The system will

always start in operator lockout mode.

The Display at Power ON will be:

READY

press START

Unlock the controller by pressing 1 & 3 simultaneously for three seconds.

The Display will still be:

READY

press START

Press Step and the Display will change to

LOW LEVEL SENSOR

enabled

To disable the low level sensor, press the Toggle Arrow then press ENTER

Press Step and the Display will change to

HOMING

OFF

To enable homing, press the Toggle Arrow then press ENTER

Press Step and the Display will change to

Speed: 10 RPM

Dist: 90 deg

To change the speed (revolutions per minute), type the desired speed with key pad,

then press ENTER

To change the distance (in degrees) that product will dispense, type the desired

distance using the key pad, then press ENTER

Notice: The distance setting determines how far the rotation motor receives power

and is intended to be an aid in initial set up not as an absolute setting of rotation. Higher

speed setting and heavier part weights create momentum that will cause mounting plate to

carry beyond the preset degrees in a repeatable fashion.

Press Step and the Display will change to

DS Position: 0

OFF Delays: 0.0

To set the Dispense Start position (how far the disc will rotate before dispense

starts) type the desired distance, in degrees, then press ENTER

To set the desire off delay (how long in seconds the disc will rotate after dispense

stops, type the desired time then press ENTER

Press Step and the Display will change to

READY

press START

You have completed Controller Set Up. The Controller will remain unlocked until power

is turned off.

Notice: The settings can be tested without exiting mode by pressing 1 & ENTER.

This will start a cycle.

Changes can be made by pressing STEP key until you get to the desired parameter.

To save the changes and exit Program Mode, simply turn the power off.

5.3 Mounting Plate

The drawing below shows the RB10 Rotary Dispense System mounting plate. This

through holes on the mounting plate can be used for fixture alignment and the threaded ¼-

20 holes can be used to secure the fixture.

This manual suits for next models

Table of contents

Other Henkel Dispenser manuals

Henkel

Henkel Loctite 97008 User manual

Henkel

Henkel OSI Service manual

Henkel

Henkel LOCTITE 97130 User manual

Henkel

Henkel Loctite Shot Miser User manual

Henkel

Henkel Loctite EQ HD12 Manual

Henkel

Henkel Loctite 98427 User manual

Henkel

Henkel Loctite 98548 User manual

Henkel

Henkel Loctite 97631 User manual

Henkel

Henkel Loctite User manual

Henkel

Henkel Loctite EQ RC40 User manual

Popular Dispenser manuals by other brands

Silver King

Silver King Majestic SK12MAJ Technical manual and replacement parts list

Franke

Franke F3Dn Twin Service manual

STIEBEL ELTRON

STIEBEL ELTRON UltraHot Plus Operation and installation instructions

DAN DRYER

DAN DRYER 282 installation guide

Essity

Essity Tork 473208 manual

CBS

CBS SD300BU-88 COMPONENT MAINTENANCE MANUAL WITH ILLUSTRATED PARTS LIST

Sealey

Sealey MK77 manual

Fluid Management

Fluid Management Accutinter 1600 End user guide

Franke

Franke DVS SD99-010 Installation and operating instructions

Graco

Graco Dispensit 1053-10C operation & maintenance

ITALTINTO

ITALTINTO i50 user manual

Coca-Cola

Coca-Cola FREESTYLE 9000 user guide

Graco

Graco ProMix 2KE Operation

TECHCON SYSTEMS

TECHCON SYSTEMS TS1251 user manual

Wayne

Wayne GLOBAL VISTA CNG instruction manual

clarsen

clarsen H133 Instructions for use

PicoBrew

PicoBrew Zymatic user manual

BOWMAN

BOWMAN BP-007 manual