Henden H3 User manual
H3 Robotic Pool Cleaner
QUICK START
GUIDE
HELPFUL HINTS
• When working, the power supply should be placed
in the shade.
• Release minimal required floating cable length to
ensure proper pool coverage.
• Leave excess cable rolled outside the pool.
• After each cleaning cycle wash the filter bag or
cartridge. Clogged filter bags reduce scanning and
cleaning efficiency.
• To remove kinks stretch the cable out completely
and let it sit for at least a day in the sun.
• Once a week unplug the cable from the power supply,
unwind the tangled portions of the cable, straighten it
out and leave it in the sun for several hours.
• When not in use, store the pool cleaner in a shady
place upside down.
SPECIFICATIONS
• Use the Robotic Pool Cleaner in the following
water conditions only: Chlorine Max 4 ppm;
pH 7.0-7.8; Temperature 6-34°C (43-93°F);
NaCl Maximum = 5000 ppm.
• Digital Power Supply: Input: 220-240 AC Volts;
50-60 Hertz; 120 Watt; Output: <30 VDC; IP 54.
• Motor protection: IP 68
Minimum depth: 0.80m/2.6ft
Maximum depth: 5m/16.4ft
Thank you for purchasing the Henden H3 Robotic Pool Cleaner.
The Henden H3 uses clever cleaning and navigation technology to keep your pool
sparkling all year long. Designed for easy use and maintenance, the Henden H3 is
a quality piece of pool equipment guaranteed to last.
CAUTIONS AND WARNINGS:
Use the originally supplied power
supply only.
Do not use an extension cable in any
case whatsoever.
Ensure the electrical outlet is protected
by a ground fault interrupter (GFI) or an
earth leakage interrupter.
Keep the power supply out of standing water.
Do not enter the pool while the Robotic Pool Cleaner
is working.
Unplug the power supply before servicing.
Do not pull the Robotic Pool Cleaner from the pool
using the cable.
IMPORTANT
Please read carefully
Register your product online:
www.hendenpools.com.au/productregistration
2HENDEN – QUICK START GUIDE
H3 OPERATION
Setup
Before using the Robotic Pool Cleaner for the first time, perform the following steps:
Into the Pool
Attach the floating cable to the power supply. Position the power supply at least 3m/10ft away from
the edge of the pool.
Operation Out of the Pool
Place the Robotic Pool
Cleaner into the pool.
Release it and let it sink to
the floor. Make sure that
the floating cable is free
of any obstructions.
Turn the power supply ON.
The Robotic Pool Cleaner will
now operate until it has reached the end of the
cleaning cycle.
Open the filter cover. Open the latch to release
the bottom lid.
Rinse well with hose. Once
debris is removed close
and place back into your
cleaner.
The basket handle will
automatically pop up,
making it easy for you
to lift the basket out.
Storage
Coil the cable and store in a cool dry space upside down, or store in a caddy. DO NOT store the robot where it
will be exposed to direct sunlight, excessive heat or to frost.
Cleaning the Basket
It is highly recommended to clean the filter basket after each cleaning cycle. Note: Don’t let the ultra-fine filter
cartridges dry out before cleaning.
Unplug the power supply before servicing.
1
23m/10ft
1 2
3 4 5
6a 6b 6c 6d
7
CLICK
CLICK
1 2
1
ON
3HENDEN – QUICK START GUIDE
H3 MAINTENANCE
Periodic Filter Cleaning
Dismantle the 4 ultra-fine filter panels on the basket according to the following steps:
Position your thumbs on panel and apply pressure until
it pops out. Repeat for all 4 panels.
Clean the filters with a hose.
H3 Robotic Pool Cleaner
Cleaning the Impeller
If you notice debris trapped in the impeller:
Clean the debris trapped in the impeller opening, according to the following steps:
Unplug the power supply before servicing.
Reassemble the 4 filter panels. Insert the clean filter basket and close the filter cover.
12
3
1 2 3
CLICK CLICK
1
2
3
4
HENDEN H3 POWER SUPPLY
BASIC OPERATION
• Plug the Power Supply into an electrical outlet.
• Press the ON button. The LEDs will turn on
and the robot will start to operate. If no
programme is selected, the robot will perform
a single cleaning cycle. The Power Supply will
turn off automatically after 3 hours.
• You can programme the Power Supply at any
time. See the relevant section below for more
details on each program.
*Bluetooth is not available for this model.
WEEKLY TIMER
Your robot has a weekly
timer feature that enables
you to set an automatic
cleaning schedule for the
week ahead.
When the power supply is switched on, you can
press the weekly timer button to select one of
the following cleaning schedule options for the
week ahead:
One click – The robot will automatically
work every day for a full cycle, that is, once a
day for 7 days.
Two clicks – The robot will automatically
work every alternate day for a full cycle,
that is, 4 times in a week.
Three clicks – The robot will
automatically work every 3 days,
that is, 3 times a week.
After selecting one of the above options, the
robot will start to operate at the next occurrence
of the programmed start time.
Note: A fourth click will cancel the cleaning
schedule programme (without a visible
indication).
If the robot is working in the weekly timer mode,
the weekly timer button constantly blinks between
cycles. At the end of the week, the power supply
automatically switches off and you need to
reschedule the robot.
1
2
3
Register your product online:
www.hendenpools.com.au/productregistration
ON/OFF
WEEKLY TIMER
1 2 3
Other manuals for H3
1
Other Henden Swimming Pool Vacuum manuals
