Heatsail BEEM User manual
For the most recent version of this manual, check our website.
Do not discard this manual, as it contains your device’s serial number.
BEEM® MANUAL
1. Electrical safety procedures & requirements
2. Operational safety
3. Maintenance
4. Warranty conditions
5. Applicable law – competent court
6. Assembly and wiring instructions
7. Operation
8. Troubleshooting
1. Consignes de sécurité électrique & conditions d‘utilisation
2. Sécurité
3. Entretien
4. Conditions de garantie
5. Droit applicable
6. Installation illustrée et schémas de connexion
7. Opération
8. Dépannage
6
7
8
10
11
12
21
21
25
26
27
29
30
31
40
40
EN
FR
4Heatsail BEEM®
EN
Thank you for your purchase!
This manual is inextricably linked to the BEEM®and must
always be kept by the user or by the responsible person.
Read the user instructions carefully. It contains essential
information about safety, use, cleaning and maintenance
of the BEEM. Heatsail cannot be held liable for damage to
persons, animals and objects resulting from non-compliance
with the instructions in the user manual.
Heatsail reserves the right to make changes to the product,
technical features and instructions at any time and without
prior notice.
If you resell the BEEM, transfer it to another user or leave it
behind when relocating, the manual must be made available
to the new user.
We wish you many warm and pleasant evenings with our
BEEM.
5Manual
EN
User manual
Operating, maintenance and installation.
Attention
Please read through these instructions carefully before using your BEEM.
Do not discard this manual, as it contains your device’s serial number.
6Heatsail BEEM®
EN
1. Electrical safety procedures
& requirements
The use of the BEEM requires an electrical system with sound safety
grounding. The electrical safety of the device is only assured if it is
correctly connected to a grounding system built in accordance with
safety regulations. It must be inspected before use. If anything is unclear,
a qualified and authorized person must be consulted. Heatsail is not
responsible for damage caused by an ungrounded device.
The installation of the BEEM electrical components requires a main
connection of 240V-50/60Hz (16 Amp fuse AND 30 mA RCD for the single
BEEM, 20 Amp fuse AND 30 mA RCD for the double BEEM): the connection
must be properly implemented in accordance with the applicable IEC-CEI
standards and local ordinances.
This product must by installed by a licensed electrician and the power
supply connection should be in accordance with the requirements of
NFPA 70 and OSHA Regulations 29 CFR 1910.304(b)(2).
Please note: Statutory and other local regulations may apply. The
electrical power supply will need to be interrupted using lock-out/tag-out
procedures before work on the electrical components can be carried out.
Electric adapters, power strips and/or extension cords may not be used
for the BEEM electrical supply. A switch must be installed between the
BEEM and the fuse box at all times. Non-compliance with these instruc-
tions may compromise the safety of the device. Heatsail will not be held
liable for any damage resulting from these issues.
7Manual
EN
2. Operational safety
A minimum clear height of 71 inches (1.80 meters) must be observed for the
BEEM, measured between the ground and bottom of the lowest heating
element at the time of installation.
Children must be under adult supervision at all times when near this
product, when in use. This product is not intended to be operated by
children, to be played with or to be played on. The BEEM must be kept out
of reach of anyone incapable of assessing the risks which can arise from
the (improper) use of electrical equipment.
Do not use the BEEM in small rooms when occupied by persons not
capable of leaving the room on their own, unless constant supervision is
provided.
CAREFUL - The heater reaches very high temperatures and can cause
burns. The BEEM must never be touched after it is switched on.
Special attention must be given when children and vulnerable people
are present.
The BEEM will remain hot for a considerable period of time after it has been
switched o. Do not touch the BEEM for a period of 40 minutes after it has
been switched o. Caution should be exercised at all times.
The BEEM must never be used when the glass is damaged.
The BEEM may not be used with a timer or any device which can
automatically switch on the heating as there is a risk of fire if the BEEM
has been incorrectly positioned or if items have been placed within
the minimum safe operating distance.
Never use the BEEM in the immediate vicinity of a bath, jacuzzi, shower,
or swimming pool.
8Heatsail BEEM®
EN
To reduce the risk of fire, keep textiles, curtains, or any other flammable
material a minimum distance of 40 inches (100 cm) from the BEEM. Never
cover your BEEM without disconnecting the power supply via the circuit
breaker.
The BEEM must never be touched with bare, wet or damp body parts.
The BEEM is constructed of six (BEEM 230, BEEM 290) or eight (BEEM
390, BEEM 520) high-radiance ceramic heating elements, mounted on a
reflective plate. The full operating temperature will be reached within 30
minutes.
Please note: There is no noticeable glow in the infrared area.
Never use the BEEM to light anything on fire. The ceramic elements are
fragile and must be handled with care. The same also applies to the glass
casing.
The BEEM can only be installed at covered places.
The BEEM is not allowed for use in greenhouses or construction sites.
Always keep the BEEM free of snow.
Heatsail will not be held responsible for damage resulting from
non-compliance with the instructions regarding use and maintenance.
3. Maintenance
3.1. Cleaning
Your BEEM must be cleaned on a monthly basis.
The electrical supply must be disconnected via the installation’s breaker
switch before cleaning activities can commence. Cleaning may only be
done with a dry and soft cloth. Do not use any abrasive cloths. Do not
use detergents. Using a high-pressure and/or steam cleaner is prohibited.
Cleaning is only permitted once the BEEM has completely cooled down.
Non-compliance with these rules may compromise the safety of the
device. Heatsail will not be held responsible for damage resulting from
non-compliance with the cleaning instructions.
9Manual
EN
3.2. Replacing the bulb
Your BEEM is supplied with six (BEEM 230, BEEM 290) or eight (BEEM 390,
BEEM 520) G9 halogen bulbs of 120V/ 40 Watt as standard. The maximum
permitted output power is 40 Watt per bulb.
The electrical supply must be disconnected via the installation’s breaker
switch before the bulb can be replaced.
You can replace the bulb by carefully lifting up the glass panel and remove
it by turning it. The bulb is held in place by a spring. Remove the bulb by
pulling gently to release it from the holder. Then replace the bulb and
reverse previous steps.
Please note: Be careful never to touch the halogen bulb with bare fingers,
as oils from skin will significantly reduce bulb life.
3.3. Inspection
The BEEM must be subjected to an annual inspection.
The user is not authorized to carry out his own inspections and repairs.
Inspection of the BEEM must exclusively be carried out by qualified and
authorized technicians, in accordance with Heatsail’s applicable standards
and regulations. “Qualified technicians” are understood to mean: qualified
electricians who are familiar with the applicable electrical laws and
regulations in accordance with the requirements of NFPA 70 and OSHA
Regulations 29 CFR 1910.304(b)(2).
The electrical supply must be disconnected via the installation’s main
breaker before any work can be carried out.
All repairs must be requested via Heatsail or an authorized distributor of
Heatsail products. A repair is only valid when original parts have been
used.
Upon written approval by Heatsail, the entire control panel should be
returned in case of a defective cable.
Heatsail will not be held responsible for damage resulting from non-
compliance with the maintenance instructions.
10 Heatsail BEEM®
EN
4. Warranty conditions
4.1. Warranty
Your BEEM comes with a two-year, limited warranty. The original invoice will
serve as your proof of purchase. This warranty does not aect the buyer’s
rights by virtue of the national legislation regarding the sale of consumer
goods. This warranty is only valid if the BEEM installation and maintenance
have been carried out in accordance with the applicable standards
and regulations and instructions for the installation, use, cleaning and
maintenance of the product, by qualified individuals who satisfy the
legal requirements.
The warranty term will commence from the date the goods were delivered.
Any defective goods will be reviewed by Heatsail or an authorized Heatsail
distributor. Once Heatsail has deemed a fault as a warranty situation, the
Heatsail unit(s) will be brought to Heatsail or a local distributor for repair
and returned in a timely manner.
Heatsail and its distributors will not award any compensation for any direct
or indirect damage resulting from, or relating to, using the product.
The replaced parts will be under warranty for the remainder of the warranty
period from the date the goods are delivered.
4.2. Warranty exclusions
• The conditions for activating the warranty were not met.
• The parts appear to be defective as a result of negligence or
inappropriate use or incorrect maintenance.
• The installation has not been carried out in accordance with the legal
standards and not in accordance with the instructions provided in the
user manual.
• Any damage caused as a result of weather conditions, chemical and
electrochemical reactions, improper use, natural disasters, electrical
discharge, fire, a defective electrical installation, modifications or
mishandling to packaging, the handle and the electrical wiring.
• Any damage caused by transport.
Other manuals for BEEM
2
Table of contents
Languages:
Other Heatsail Light Fixture manuals
Popular Light Fixture manuals by other brands
Emos
Emos CLASSIC ZY1431T manual
Westinghouse
Westinghouse Outdoor Lighting Fixture owner's manual
Hedler
Hedler C 12 silent Operation manual
Blizzard Lighting
Blizzard Lighting Puck: CSI manual
Energetic Lighting
Energetic Lighting ELYSL-5004 Series installation instructions
Lightmaxx
Lightmaxx Shaft 5R user manual
Cooper Lighting
Cooper Lighting Halo L3232E Specification sheet
Stageline
Stageline ODW-2410RGBW instruction manual
Light Sky
Light Sky Tornado Series user manual
Lightolier
Lightolier Paralyte 2424 PLA2G9LS26U specification
Lightolier
Lightolier Lytespan 83ED17S specification
Lightolier
Lightolier Calculite CS8226 specification