Haven Isotunes User manual
Introduction
Thank you for purchasing ISOtunes
™
Premium Noise Isolating Earbuds.
These earbuds have been specifically designed for use in noisy
environments – allowing you to block out much of the surrounding
noise so that you can listen to your music or talk on the phone with
less interruption. This product has been tested and meets the ANSI
& NIOSH standards for a hearing protector, with a Noise Reduction
Rating (NRR) of 26 dB, and is designed such that you cannot damage
your hearing, at any sound level. Full testing details are available in the
Noise Attenuation section of this booklet.
1. Speakers
2. Battery Box
3. Indicator Light
4. Volume Up Button (+)
5. Multifunction Button (MFB)
6. Volume Down Button (-)
7. Left & Right Magnets
8. Micro USB Charging Port
9. Microphone
1 7
89
23
456
Fitting
ISOtunes
™
comes with 3 sets of foam eartips (S,M,L) and 3 sets of
rubber eartips (S,M,L). The foam eartips provide maximum noise
reduction while the rubber eartips are recommended for use when NOT
in noisy situations. Choose the size that fits most snugly in your ear
canal. Remember, the snugger the fit, the better the noise attenuation.
The foam eartips have been specifically designed by Comply
™
Foam
for use with ISOtunes
™
to provide maximum noise isolation for a
superior audio experience. They are made from a heat-activated
memory foam which allows long term, comfortable wear and enhanced
sound performance.
For maximum noise reduction, first roll the foam eartip between your
thumb and forefinger. Then, place the earbud into your open ear canal.
Hint: To open your ear
canal wider, lift the top
of your ear up and away
from your head, as shown
in the diagram. After
the earbud has been
placed, the foam tip will
expand to fill your ear
canal, providing you with
superior noise isolation
for the best possible
listening experience.
Included with your ISOtunes
™
are a pair of SecureFit tips (pictured
below) that can be used to stabilize the headphones during sports
activities. To put each fit tip on, simply remove the earbud and place
the ring over the earphone. Then, after replacing the earbud, fit the
earphone with the fit tip resting snugly against your inner ear.
Additionally, two mini
cable clips have been
included to tie back and
secure excess wire.
These will allow you to
wear your ISOtunes
™
comfortably while
participating in
mobile activities,
such as running.
Operating Your ISOtunes™Headphones
On/Off
To turn on your ISOtunes™, press and hold the Multifunction Button (MFB)
for 2 seconds, or until you hear “Power On” through the speakers. The
indicator light will turn blue for 1 second to confirm the power is on.
To turn off your ISOtunes™, press and hold the MFB for 3 seconds, or until
you hear “Power off” through the speakers. The indicator light will turn red
for 1 second to confirm the power is off.
Recharging
We recommend charging your ISOtunes™ fully before its first use. Use the
included USB charger to connect to the micro-USB port on the controller
of the headphones. A red LED indicates your headset is charging, while a
blue LED indicates the charging has finished. When the battery is low, the
indicator light will flash red, accompanied by periodic beeps. ISOtunes™
supports iOS Bluetooth® battery level indicator.
Audio Control Functions
Volume Adjustments: Use the Volume Up (+) and Volume Down (-) buttons
to adjust the volume.
Play and Pause Music: Press the MFB once; or, separate/connect the
magnetic earphones; or, control on your Bluetooth®-enabled device.
Forward/Backward Song Selection: Press and hold the Volume Up (+)
button for 2 seconds to skip to the next song. Press and hold the Volume
Down (-) button for 2 seconds to return to the previous song.
Bluetooth Pairing
Press and hold the MFB until the indicator light flashes red AND blue
interchangeably, or until you hear “Pairing” through the speakers. Your
ISOtunes™ must be within 3 feet of the device you’re pairing with.
Search for and select “ISOtunes” in the Bluetooth® settings of your pairing
device. You will then hear “Paired. Your phone is connected.” through the
speakers. If prompted, use input code “0000” to pair.
After powering off and powering back on again, ISOtunes™ will
automatically reconnect with its paired device, if in range.
To delete a pairing record, press and hold both the Volume Up (+) and
Volume Down (-) buttons until the red and blue LED light flashes twice at
the same time. Then, when prompted by a “beep”, press and hold the MFB
for 3 seconds or until the devices are disconnected.
Voice Dialing: If your mobile phone is enabled for voice dialing, press and
hold the Volume Down (-) button for 2 seconds while connected, then
speak after you hear a beep.
DualConnect Function
ISOtunes™ is capable of connecting with two Bluetooth®-enabled phones
at the same time.
To pair two devices at the same time:
1. From OFF mode, press and hold the MFB until the indicator light flashes
red and blue alternately, entering pairing mode. Pair with phone A.
2. Turn off the Bluetooth® switch for phone A. Your ISOtunes™ will return
to unconnected status.
3. From OFF mode, press and hold the MFB until the indicator light flashes
red and blue alternately, entering pairing mode. Pair with phone B.
4. Then, turn on phone A’s Bluetooth® switch again. Your ISOtunes™ will
now be connected to both.
Phone Call Functions
Answering Calls: Press the MFB once; or, separate the magnetic earphones;
or, answer on your Bluetooth®-enabled device.
Ending Calls: Press the MFB once; or, connect the magnetic earphones; or,
end the call on your Bluetooth®-enabled device.
Rejecting Calls: Press and hold the Volume Up (+) button for 2 seconds.
Transferring Calls: During a phone conversation through the headphones,
press and hold the Volume Down (-) button for 2 seconds to switch the call
to your mobile phone. During a phone conversation on your mobile phone,
press and hold the Volume Down (-) button for 2 seconds to switch the call
to the headphones.
Last Number Redialing: Press the MFB twice to redial the last number you
connected with.
Muting Calls: Press and hold the Volume Up (+) button for 2 seconds to
mute a call. Press and hold it again for 2 seconds to take the call off mute.
Noise Attenuation
APPROVAL: ISOtunes
™
is tested and approved in accordance with ANSI S3.19-1974
Specifications.
The level of noise entering a person’s ear, when ISOtunes
™
headphones
are worn as directed, is closely approximated by the difference between the
A-weighted environmental noise level and the Noise Reduction Rating (NRR).
Improper fit of this device will reduce its effectiveness in attenuating noise.
Consult the enclosed instructions for proper fitting.
Example:
1. The surrounding noise level measured at the ear is 100 dB.
2. The NRR of ISOtunes
™
is 26 dB.
3. The noise level entering the ear is approximately equal to 74 dB.
Please note that the NRR is based on the attenuation of continuous noise and may not be
an accurate indicator of the protection attainable against impulsive noise, such as gunfire.
Shift Between Calls on Two Devices
While on a call with phone A, you can answer a call from phone B by
pressing the MFB once. This will put the call from phone A on hold. Press
the MFB again to shift back to the original call.
While on a call with phone A, you can end the call and answer a call with
phone B by pressing and holding the MFB for 2 seconds.
SafeSound™ Technology
If your device incorporates SafeSound™ Technology, its volume output has
been limited to 85 decibels. 85 decibels is the maximum volume limit allowed
by OSHA in the workplace over an 8 hour period. ISOtunes™ devices with
SafeSound™ Technology are OSHA, NIOSH, and ANSI compliant.
Frequency, Hz 125 250 500 1000 2000 3150 4000 6300 8000 NRR
Grand Mean Attenuation, dB 28.5 25.4 30.3 32.8 37.7 42.0 40.9 44.0 44.6
Standard Deviation, dB 2.8 2.3 3.0 3.8 2.8 3.3 3.6 2.7 3.4 26
Guarantee
There is a one year guarantee against defects in material and workmanship. The guarantee
does not cover damage by misuse, abuse or unauthorized modifications.
Maintenance
• Clean your Comply
™
Foam Tips by gently wiping them with a clean, damp cloth. Use water
only. Do not clean tips with alcohol-based cleaning solutions. Let tips dry completely before
next use. To ensure peak performance, we recommend replacing Comply
™
Foam Tips every
three months or when they become soiled. In order to purchase additional tips, please go to
www.complyfoam.com/ISOtunes
• Do not use abrasive cleaning solvents to clean the headset.
• Avoid scratching the headset with sharp objects, as this may cause damage.
• Keep the headset away from high temperature areas, humidity, and dust.
WARNING:
ISOtunes
™
does an excellent job of blocking outside noise. As such, ISOtunes
™
should NOT
be used in environments where users need to be fully aware of their surroundings for personal
safety reasons. For example, do NOT use them while driving a car or riding a motorcycle.
Similarly, do NOT use them when riding a bicycle outside. The user is solely responsible for
ensuring that ISOtunes
™
is used ONLY in safe environments.
Additional Notes
• ISOtunes
™
is compliant with Bluetooth
®
V4.1. We do not guarantee compatibility of all functions
on every Bluetooth
®
-enabled device. Please check your device’s user manual for compatibility and
functionality.
• ISOtunes™ will turn off automatically if not connected with any Bluetooth
®
device within 20 minutes.
• If the magnetic control function isn’t working, this is likely due to dirt or sweat on the magnet. Simply
clean this off to return the control function back to normal.
Specifications
Bluetooth
®
V4.1 Technology
Bluetooth
®
profiles supported: HSP, HFP, A2DP, AVRCP
Supports iOS Bluetooth
®
battery level indicator
Sweat proof and water resistant
Transmission power: Class 2
Operation range: Up to 10 meters
Frequency range: 2.402-2.48 GHz
Battery: Built-in rechargeable 3.7V/60mAH Lithium
Battery
Integrated microphone for hands-free calling
Supports voice commands
High quality microphone offers noise suppression and
echo cancellation
Charging voltage: DC4.75-5.25V
Charging time: About 2 hours
Music time: up to 3.5 hours*
Talk time: up to 4 hours*
Standby time: Up to 150 hours
Dimensions(mm): 38Lx10.5Wx6.5H
Weight: About 16 g
*Time may vary based on user settings.
© 2016 Hearing Components. Comply is a registered trademark of Hearing Components.
The Bluetooth
®
word mark and logos are registered trademarks owned by Bluetooth SIG, Inc.
Introducción
Gracias por adquirir los Auriculares Premium de Aislamiento de Ruido
ISOtunes
™
.
Estos auriculares han sido diseñados específicamente para su uso
en entornos ruidosos, lo que le permitirá bloquear mucho del ruido
circundante, de manera que pueda escuchar música o hablar por
teléfono con menos interrupciones. Este producto ha sido probado
y cumple con las normas ANSI y NIOSH para un protector auditivo,
con una Clasificación de reducción de ruido (NRR) de 26 dB, y es
diseñado de tal forma que no pueda dañar su audición, en cualquier
nivel de sonido. Los detalles completos de prueba están disponibles
en la sección de Atenuación de ruido de este folleto.
1. Altavoces
2. Caja de batería
3. Luz indicadora
4. Botón para subir volumen (+)
5. Botón Multifunción (MFB)
6. Botón para bajar volumen (-)
7. Imanes izquierdo y derecho
8. Puerto de carga Micro USB
9. Micrófono
1 7
89
23
456
Ajuste
ISOtunes
™
viene con 3 conjuntos de olivas de espuma (S,M,L) y
3 conjuntos de olivas de caucho (S,M,L). Las olivas de espuma
proporcionan la máxima reducción de ruido mientras que las olivas
de caucho son recomendadas para su uso cuando NO se está en
situaciones ruidosas. Elija el tamaño que se adapta más cómodamente
a su canal auditivo. Recuerde, mientras más ajustado sea el ajuste,
mejor será la atenuación del ruido.
Las olivas de espuma han sido diseñadas específicamente por
Comply
™
para utilizar con ISOtunes
™
para proporcionar el máximo
aislamiento del ruido para una experiencia de audio superior. Son
fabricadas con una espuma con memoria activada por calor que
permite comodidad de uso a largo plazo y rendimiento de sonido
mejorado.
Para obtener la máxima reducción de ruido, primero coloque la oliva
de espuma entre su pulgar y dedo índice. Luego coloque el auricular
en el conducto auditivo abierto.
Sugerencia: Para abrir el
conducto auditivo en una
manera más amplia, levante
la parte superior de la oreja
hacia arriba y lejos de la
cabeza, como se muestra
en el diagrama. Después
de colocar la oliva, la punta
de espuma se expande
para llenar el conducto
auditivo, proporcionándole
un excelente aislamiento del
ruido para obtener la mejor
experiencia de sonido posible.
Table of contents
Languages:
Other Haven Headphones manuals
Haven
Haven ISOtunes WIRED User manual
Haven
Haven ISOtunes FREE EN352 User manual
Haven
Haven ISOtunes FREE EN352 User manual
Haven
Haven ISOtunes FREE EN352 User manual
Haven
Haven ISOtunes PRO Bluetooth User manual
Haven
Haven ISOtunes XTRA User manual
Haven
Haven ISOtunes WIRED User manual
Haven
Haven ISOtunes FREE Aware IT-15 User manual
Haven
Haven ISOtunes XTRA User manual
