Hand Held Products Quick Check PC600 User manual

Quick Check® PC600

Bar Code Verifier

User’s Guide

Disclaimer

Hand Held Products, Inc. (“Hand Held Products”) reserves the right to make

changes in specifications and other information contained in this document

without prior notice, and the reader should in all cases consult Hand Held

Products to determine whether any such changes have been made. The

information in this publication does not represent a commitment on the part of

Hand Held Products.

Hand Held Products shall not be liable for technical or editorial errors or

omissions contained herein; nor for incidental or consequential damages

resulting from the furnishing, performance, or use of this material.

This document contains proprietary information that is protected by copyright. All

rights are reserved. No part of this document may be photocopied, reproduced,

or translated into another language without the prior written consent of Hand

Held Products.

Web Address: www.handheld.com

Statement of Agency Compliance

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

FCC Class A Compliance Statement

This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to

cause harmful interference, in which case the user will be required to correct the

interference at his own expense.

Caution: Any changes or modifications made to this equipment not

expressly approved by Hand Held Products, Inc. may void the FCC

authorization to operate this equipment.

Note: To maintain compliance with FCC Rules and Regulations, cables

connected to this device must be shielded cables, in which the cable shield

wire(s) have been grounded (tied) to the connector shell.

Canadian Notice

This equipment does not exceed the Class A limits for radio noise emissions as

described in the Radio Interference Regulations of the Canadian Department of

Communications. (ICES-003)

Le present appareil numerique n'emet pas de bruits radioelectriques depassant

les limites applicables aux appareils numeriques de la classe A prescrites dans

le Reglement sur le brouillage radioelectrique edicte par le ministere des

Communications du Canada. (ICES-003)

The CE mark on the product indicates that the system has been tested

to and conforms with the provisions noted within the 89/336/EEC

Electromagnetic Compatibility Directive and the 73/23/EEC Low Voltage

Directive.

For further information please contact:

Hand Held Products, Inc.

Nijverheidsweg 9

5627 BT Eindhoven

The Netherlands

Hand Held Products shall not be liable for use of our product with equipment (i.e.,

power supplies, personal computers, etc.) that is not CE marked and does not

comply with the Low Voltage Directive.

Limited Warranty

Hand Held Products, Inc., ("Hand Held Products") warrants its products to be

free from defects in materials and workmanship and to conform to Hand Held

Products' published specifications applicable to the products purchased at the

time of shipment. This warranty does not cover any Hand Held Products product

which is (i) improperly installed or used; (ii) damaged by accident or negligence,

including failure to follow the proper maintenance, service, and cleaning

schedule; or (iii) damaged as a result of (A) modification or alteration by the

purchaser or other party, (B) excessive voltage or current supplied to or drawn

from the interface connections, (C) static electricity or electro-static discharge,

(D) operation under conditions beyond the specified operating parameters, or (E)

repair or service of the product by anyone other than Hand Held Products or its

authorized representatives.

This warranty shall extend from the time of shipment for the duration published

by Hand Held Products for the product at the time of purchase ("Warranty

Period"). Any defective product must be returned (at purchaser’s expense)

during the Warranty Period to Hand Held Products' factory or authorized service

center for inspection. No product will be accepted by Hand Held Products

without a Return Materials Authorization, which may be obtained by contacting

Hand Held Products. In the event that the product is returned to Hand Held

Products or its authorized service center within the Warranty Period and Hand

Held Products determines to its satisfaction that the product is defective due to

defects in materials or workmanship, Hand Held Products, at its sole option, will

either repair or replace the product without charge, except for return shipping to

Hand Held Products.

EXCEPT AS MAY BE OTHERWISE PROVIDED BY APPLICABLE LAW, THE

FOREGOING WARRANTY IS IN LIEU OF ALL OTHER COVENANTS OR

WARRANTIES, EITHER EXPRESSED OR IMPLIED, ORAL OR WRITTEN,

INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

HAND HELD PRODUCTS’ RESPONSIBILITY AND PURCHASER’S

EXCLUSIVE REMEDY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR

OR REPLACEMENT OF THE DEFECTIVE PRODUCT. IN NO EVENT SHALL

HAND HELD PRODUCTS BE LIABLE FOR INDIRECT, INCIDENTAL, OR

CONSEQUENTIAL DAMAGES, AND, IN NO EVENT, SHALL ANY LIABILITY

OF HAND HELD PRODUCTS ARISING IN CONNECTION WITH ANY

PRODUCT SOLD HEREUNDER (WHETHER SUCH LIABILITY ARISES FROM

A CLAIM BASED ON CONTRACT, WARRANTY, TORT, OR OTHERWISE)

EXCEED THE ACTUAL AMOUNT PAID TO HAND HELD PRODUCTS FOR

THE PRODUCT. THESE LIMITATIONS ON LIABILITY SHALL REMAIN IN

FULL FORCE AND EFFECT EVEN WHEN HAND HELD PRODUCTS MAY

HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH INJURIES, LOSSES,

OR DAMAGES. SOME STATES, PROVINCES, OR COUNTRIES DO NOT

ALLOW THE EXCLUSION OR LIMITATIONS OF INCIDENTAL OR

CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION

MAY NOT APPLY TO YOU.

All provisions of this Limited Warranty are separate and severable, which means

that if any provision is held invalid and unenforceable, such determination shall

not affect the validity of enforceability of the other provisions hereof. Use of any

peripherals not manufactured/sold by Hand Held Products voids the warranty.

This includes but is not limited to: cables, power supplies, cradles, and docking

stations. Hand Held Products, Inc. extends these warranties only to the first end-

users of the products. These warranties are nontransferable.

The limited duration of the warranty for the Quick Check PC600 Bar Code

Verifier is for two (2) years.

Table of Contents

Introduction.......................................................................................1

Getting Started with Quick Check®PC.............................................2

Unpacking / What's Included............................................................................. 2

Quick Check®PC Quick Start...........................................................3

Quick Check®PC Installation and Setup.........................................6

Quick Check®PC Features.............................................................11

Summary Grade Information........................................................................... 13

General Scan Results....................................................................................... 14

Reflectance Measures...................................................................................... 15

ISO/IEC Scan Grade........................................................................................ 15

Format Parameters.......................................................................................... 16

Dimensional Parameters ................................................................................. 16

Additional Data ............................................................................................... 17

Status Bar ........................................................................................................ 18

Additional Features......................................................................................... 18

Configuration and Settings.............................................................................. 19

Verification Parameters................................................................................... 19

Scan Direction .................................................................................19

Using Quick Check®PC..................................................................20

Wand/Mouse Aperture Selection...................................................................... 21

View Individual Scan Results........................................................................... 23

View Scan Reflectance Profile......................................................................... 24

Bar/Space Analysis.......................................................................................... 24

Calculate “X”.................................................................................................. 24

Notes................................................................................................................ 25

Reflectometer................................................................................................... 25

Print Report..................................................................................................... 26

Getting Help .................................................................................................... 26

Context Sensitive Help..................................................................................... 27

Understanding Print Quality Results..............................................27

Common Corrective Actions ...........................................................32

Error messages ................................................................................34

Frequently Asked Questions ...........................................................35

Glossary of Terms............................................................................39

Additional Sources of Information.................................................56

Electrical Specifications..................................................................57

Appendix A Messages......................................................................59

Additional Data Messages:.............................................................................. 59

Error Messages: .............................................................................................. 59

Appendix B Notes for Windows .....................................................60

Additional Notes For Windows:....................................................................... 60

Technical Assistance .......................................................................60

Introduction

Hand Held Products is pleased to supply you with the Quick Check®PC bar code

verification system. The instrument and software offer an easy-to-use and

powerful combination that provides both pass/fail testing and full traditional and

ISO/IEC verification with significant detail.

This manual contains information on Quick Check®PC instrument and software.

It describes all the features and functions of the software and provides additional

information about bar code symbol quality and the ANSI X3.182 / CEN EN1635 /

ISO/IEC 15416 method of symbol verification.

This manual is organized into the following sections:

•System Requirements

•Windows®98, 2000 and NT operating system

•PC (or compatible) with 486 or better processor

•4 Megabytes of RAM

•3 Megabytes available on hard drive

•Available COM Port (COM 1-4)

•Microsoft Compatible Mouse

•Getting Started

•Quick Start Guide

•Quick Check®PC Installation and Setup

•Quick Check®PC Features

•Using Quick Check®PC

•Understanding Print Quality Results

•Common Corrective Actions

•Error Messages

•FAQs - Bar Code Basics

•Glossary of Terms

•Additional Sources of Information

•Appendix A: Additional Data Messages

•Appendix B: Setting up Windows Communications

•Technical Support

Getting Started with Quick Check®PC

Unpacking / What's Included

When you first receive your Quick Check®PC, inspect the packaging for any

signs of shipping damage. If there is evidence of damage, please keep ALL

packing materials and contact the delivery carrier as soon as possible for claim

procedure.

Unpack the Quick Check®PC carefully and confirm that you have the following

items:

•The Quick Check®PC Interface Module

•9-pin/RJ-12 serial cable

•Hand Held Products Quick Check®Mouse Wand or Pen Wand

•AC charger/power supply

•4 “AA” Rechargeable NiCad batteries

•Quick Check®PC software (CD-ROM)

•User’s Guide

•Packaged with the Manual

Ruler for measuring symbol length

Gauge ruler (showing common sizes of bar code symbols)

•Reference Symbols (6 sheets)

•Reflectance Calibration Page (QCRFPG)

If you do not have all these items, contact your sales representative.

Other manuals for Quick Check PC600

Table of contents

Other Hand Held Products Barcode Reader manuals

Hand Held Products

Hand Held Products HandHeld 3800 Linear Series User manual

Hand Held Products

Hand Held Products HandHeld 3800 Linear Series User manual

Hand Held Products

Hand Held Products SV Series User manual

Hand Held Products

Hand Held Products 2020/5620 User guide

Hand Held Products

Hand Held Products DOLPHIN RF User manual

Hand Held Products

Hand Held Products IMAGETEAM 3800E User manual

Hand Held Products

Hand Held Products IMAGETEAM 4400 User manual

Hand Held Products

Hand Held Products IMAGETEAM 4620 User manual

Hand Held Products

Hand Held Products 4230 User manual

Hand Held Products

Hand Held Products IMAGETEAM 4410 User manual

Hand Held Products

Hand Held Products 4800p User manual

Hand Held Products

Hand Held Products IMAGETEAM 3900 User manual

Hand Held Products

Hand Held Products SCANTEAM 2070 User guide

Hand Held Products

Hand Held Products IMAGETEAM 3800i Installation and operating instructions

Hand Held Products

Hand Held Products 4800p User manual

Hand Held Products

Hand Held Products 2020 User manual

Hand Held Products

Hand Held Products 4X00 User manual

Hand Held Products

Hand Held Products 2020 User guide

Hand Held Products

Hand Held Products Quick Check PC600 User manual

Hand Held Products

Hand Held Products IK8560 User manual

Hand Held Products

Hand Held Products QUICK CHECK 890 User manual

Hand Held Products

Hand Held Products 3800ESD User manual

Hand Held Products

Hand Held Products IMAGETEAM 4410 User manual

Hand Held Products

Hand Held Products IT4000 Use and care manual

Hand Held Products Quick Check PC600 User manual

Popular Barcode Reader manuals by other brands