HAMPTON BAY Copperhead 184-860 User manual

Hampton Bay Lifetime Limited Warranty

The retailer warrants the fan motor to be free from defects in workmanship and material

present at time of shipment from the factory for a lifetime after the date of purchase by the

original purchaser. The retailer also warrants that all other fan parts, excluding any glass or

plexiglass blades, to be free from defects in workmanship and material at the time of

shipment from the factory for a period of one year after the date of purchase by the original

purchaser. We agree to correct such defects without charge or at our option replace with a

comparable or superior model if the product is returned to the retailer. To obtain warranty

service, you must present a copy of the receipt as proof of purchase. All costs of removing

and reinstalling the product are your responsibility. Damage to any part such as by accident

or misuse or improper installation or by affixing any accessories, is not covered by this

warranty. Because of varying climatic conditions in the United States this warranty does not

cover any changes in brass finish, including rusting, pitting, corroding, tarnishing or

peeling. Brass finishes of this type give their longest useful life when protected from

varying weather conditions. A certain amount of wobble is normal and should not be

considered a defect. Servicing performed by unauthorized persons shall render the warranty

invalid. There is no other express warranty. The retailer hereby disclaims any and all

warranties, including but not limited to. Those of merchantability and fitness for a

particular purpose to the extent permitted by law. The duration of any implied warranty

which cannot be disclaimed is limited to the time period as specified in the express warranty.

Some states do not allow limitation on how long an implied warranty lasts, so the above

limitation may not apply to you. The retailer shall not be liable for incidental,

consequential, or special damages arising out of or in connection with product use or

performance except as may otherwise be accorded by law. Some states do not allow the

exclusion of incidental or consequential damages, so the above exclusion or limitation may

not apply to you. This warranty gives specific legal rights, and you may also have other

rights which vary from state to state. This warranty supersedes all prior warranties.

Lifetime Limited Warranty

Date Purchased

Store Purchased

Model No.

Serial No.

Vendor No.

UPC

184-860

219032

792145353171

Safety Rules.....................................................................................................................................

Unpacking Your Fan .........................................................................................................................

Installing Your Fan ...........................................................................................................................

.....................................................................................................................

Your .............................................................................................................

Care of Your Fan ............................................................................................................................

Troubleshooting .............................................................................................................................

Specifications ................................................................................................................................

Installing the Light Kit

Operating Transmitter

10.

11.

12.

13.

14.

Table of Contents

1. Safety Rules

1.To reduce the risk of electric shock, insure electricity has been

turned off at the circuit breaker or fuse box before beginning.

2. All wiring must be in accordance with the National Electrical Code

and local electrical codes. Electrical installation should be

performed by a qualified licensed electrician.

3. NOTE: Suitable for use with solid-state speed controls.

4. WARNING: To reduce the risk of personal injury, use only the two

steel screws (and lock washers) provided with the outlet box for

mounting to the outlet box. Most outlet boxes commonly used for

the support of lighting fixtures are not acceptable for fan support

and may need to be replaced, consult a qualified electrician if in

doubt.

8. Do not operate the reverse switch while the fan blades are in

motion. The fan must be turned off and the blades stopped before

reversing the blades direction.

9. Avoid placing objects in the path of the blades.

10. To avoid personal injury or damage to the fan and other items, be

cautious when working around or cleaning the fan.

11. Do not use water or detergents when cleaning the fan or fan

blades. A dry dust cloth or lightly dampened cloth will be

suitable for most cleaning.

12. After making electrical connections, spliced conductors should be

turned upward and pushed carefully up into the outlet box. The

wires should be spread apart with the grounded conductor and the

equipment-grounding conductor on one side of the outlet box.

13. Electrical diagrams are for reference only. Light kits that are not

packed with the fan must be UL Listed and marked suitable for

use with the model fan you are installing. Switches must be UL

General Use Switches. Refer to the Instructions packaged with

the light kits and switches for proper assembly.

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL

INJURY, MOUNT FAN TO OUTLET BOX MARKED ACCEPTABLE FOR

FAN SUPPORT.

5. The outlet box and support structure must be securely mounted and

capable of reliably supporting a minimum of 50 pounds. Use only UL

Listed outlet boxes marked FOR FAN SUPPORT.

6. WARNING: Use only with light kit marked "Suitable for Use in Wet

Locations"

7. The fan must be mounted with a minimum of 7 feet clearance from the

trailing edge of the blades to the floor.

WARNING

TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE

BLADE ARMS (ALSO REFERRED TO AS BRACKETS) DURING

ASSEMBLY OR AFTER INSTALLATION. DO NOT INSERT OBJECTS IN

THE PATH OF THE BLADES.

NOTE

READ AND SAVE ALL INSTRUCTIONS!

Unpack your fan and check the contents. You should have the following items;

1. Fan blades (5)

2. Canopy assembly

4. Coupling cover

5. Fan motor assembly

6. Blade arms (5)

7. Switch housing

8. Mounting plate

Ball/downrod assembly

9. Light kit

10. Glass shade

11. 13 Watt compact fluorescent bulb

13a. Wall transmitter incl. 2 mounting screws

and 3

13b. Wall plate w/2 mounting screws

14. Balancing kit

12. Receiver with 6 wire nuts

wire nuts

13a

13b

15. Loose parts bag containing:

a. Blade attachment hardware

(16 screws with )

b. Mounting hardware

( 3 plastic wire connectors)

rubber washers

WARNING

DO NOT INSTALL OR USE FAN

IF ANY PART IS DAMAGED OR MISSING.

CALL TOLL FREE 1-877-902-5588. Unpacking Your Fan 2.

Tools Required

P h i l l i p s s c r e w d r i v e r , s t r a i g h t s l o t

scre w d r iver, a d j u stable wre n c h , step

ladder, and wire cutters.

Mounting Options

If there isn't an existing listed mounting

box, then read the following instructions.

Disconnect the power by removing fuses or

turning off circuit breakers.

Secure the outlet box directly to the

b u i l d i n g st r u c t u r e . Us e a p p r o p r i a t e

fasteners and building materials. The outlet

box and its support must be able to fully

support the moving weight of the fan (at

least 50 lbs). Do not use plastic outlet

boxes.

Figures 1,2 and 3 are examples of different

ways to mount the outlet box.

Note: You may need a longer downrod to

maintai n proper bl ade cleara n c e when

installing on a steep, sloped ceiling.

Outlet box

Figure 1

Figure 2

Figure 4

3. Installing Your Fan

Provide strong support

Recessed

outlet box

Mounting bracket

opening must be

toward the top

Figure 3

Angled ceiling

maximum

18 angle

To hang your fan where there is an existing

fixture but no ceiling joist, you may need an

installation hanger bar. (Fig.4) (available at

any Home Depot store).

Hanging the Fan

REMEMBER to turn off the power. Follow

the steps below to hang your fan properly:

Step 1. Remove the decorative canopy

bottom cover from the canopy by turning the

cover counter clockwise.(Fig. 5)

Step 2. Remove the hanger bracket from the

canopy by loosening the two screws on the

bottom of the hanging bracket

from the screw head and turning the canopy

counter clockwise.(Fig. 5)

Step 3. Secure the hanger bracket to the

ceiling outlet box with the screws and

washers provided with your outlet box.

Step 4. Pass the 120-volt supply wires

through the center hole in the ceiling hanger

bracket.(Fig. 6)

Step 5. Remove the hanger pin, lock pin and

set screws from the top of the motor

assembly.

NOTE:

Step 6. Route wires exiting from the top of

the fan motor through the collar cover,

canopy cover, canopy and then through the

a half turn

If a longer downrod is needed, take

out the screw located in the hanger ball,

lower the hanger ball and remove the pin,

remove all 3 pieces from the downrod and

assemble them onto the new longer downrod

before proceeding step 6. (The longer

downrod is available at any Home Depot

store)

WARNING

FAILURE TO PROPERLY INSTALL LOCKING PIN

AS NOTED IN STEP 7 COULD RESULT IN FAN

LOOSENING AND POSSIBLY FALLING.

Step 8. Tighten two set screws on top of the fan

motor firmly. (Fig. 7)

Step 9. Place the downrod ball into the hanger

bracket socket. Rotate the downrod ball until

the groove of the downrod ball lines up with

the hook of the hanger bracket. (This will help

balance the fan.)

Step 7. Align the holes at the bottom of the

downrod with the holes in the collar on top of

the motor housing (Fig.7). Carefully insert the

hanger pin through the holes in the collar and

downrod. Be careful not to jam the pin against

the wiring inside the downrod. Insert the

locking pin through the hole near the end of

the hanger pin until it snaps into its locked

position, as noted in the circle inset of Fig. 7.

Figure 5

Ceiling

canopy

Canopy

cover

Mounting

screws

(supplied with

electrical box)

Hook

UL Listed

electrical

box

Figure 6 120V Wires

Washers

Figure 7

Hanger

bracket

Hanger

bracket

Motor wires

Ball/downrod

assembly

Hanger pin Locking

Collar cover

Downrod

Canopy

Canopy cover

Set screws

Make the Electric Connections

WARNING: To avoid possible electrical

shock, be sure electricity is turned off at the

main fuse box before wiring.

NOTE: This r e mote control unit i s

equipped with 16 code combinations to

prevent possible interference from or to

other remote units. The frequency switches

on your receiver and transmitter have been

preset at the factory. Please recheck to make

sure the switches on the transmitter and the

receiver are set to the same position, any

combination of settings will operate the fan

as long as the transmitter and receiver are

set to the same position. (Fig. 8)

Step 1. (Fig. 9) Insert the receiver into

the mounting bracket with the flat side of

the receiver facing the ceiling.

Step 2. (Fig. 10) Motor to Receiver

Electrical Connections: Connect the black

wire from the fan to black wire marked "TO

MOTOR L". Connect the white wire from

the fan to the white wire marked "TO

MOTOR N" from the receiver. Connect the

blue wire from the fan to the blue wire

marked "For Light" from the receiver.

Secure the wire connections with the plastic

wire nuts provided.

Step 3. (Fig. 10) Receiver to House Supply

Wires Electrical Connections: Connect the

black (hot) wire from the ceiling to the black

wire marked "AC in L" from the receiver.

Connect the white(neutral) wire from the

ceiling to the white wire marked "AC in N" from

the receiver. Secure the wire connections with

the plastic wire nuts provided.

Step 4. (Fig. 10) If your outlet box has a ground

wire (green or bare copper) connect it to the fan

ground wires; otherwise connect the hanging

bracket ground wire to the mounting bracket.

Secure the wire connection with a plastic nut

provided. After connecting the wires spread

them apart so that the green and white wires are

on one side of the outlet box and black and blue

wires are on the other side. Carefully tuck the

wire connections up into the outlet box.

CAUTION: Do not use with wall light

dimmer switch.

Figure 9

Receiver

Hanger

bracket

Figure 8

Frequency

switch

Figure 10

White (neutral)

Green or bare

copper (ground)

White ("AC IN N")

White ("to motor N")

Ground

(green)

(Connect to

ground wire on

hanger bracket

if no house

ground wire

exists.)

Outlet box

Black (hot)

Black ("AC IN L")

Black ("to motor L")

Receiver

Blue ("for light")

Blue (light)

Black (motor)

Fan

SUPPLY CIRCUIT

Figure 11

Wall

control

Black

White

Blue

Ground

Green

INPUT

AC120V

AC SUPPLY

WARNING: HOOK UP IN "SERIES ONLY" DO NOT CONNECT THE HOT AND

NEUTRAL WIRES OF ELECTRIC CIRCUIT TO THE TRANSMITTER WALL

SWITCH - DAMAGE TO THE SWITCH AND POSSIBLE FIRE COULD OCCUR.

Step 1. Remove the existing wall plate and switch from the wall junction box.

Step 2.

Step 3. (Fig. ) Carefully tuck the wire connections inside the junction box. Secure the wall

transmitter with the two screws provided. Attach the wall plate over the wall transmitter and

secure with the two screws provided.

Make the electrical connections as shown in (Fig. 11). If your outlet box has a ground

wire (green or bare copper) connect the wall transmitter's ground wire to it; otherwise

connect the wall transmitter's ground wire directly to one of the screws from the outlet box.

Figure 12

REMEMBER to Shut the Power Off at the Circuit Breaker or Fuse Box.

Installing the Wall Transmitter

Figure 13

Outlet box

Hanger

bracket

Canopy

cover

Screws

Finishing the Installation

Step 1. Tuck connections neatly into ceiling

outlet box.

Step 2. Slide the canopy up to ceiling and over

the 2 screws on the hanger bracket. Rotate

canopy clockwise. Next, while holding the

canopy with one hand, slide the canopy cover

over the screws and rotate clockwise until

tight. Note: adjust the canopy screws as

necessary until the canopy and canopy cover

are snug. (Fig. 13)

WARNING

Make sure the notch on the hanging bracket

properly sits in the groove in the hanger

ball before attaching the canopy to the

bracket by turning the housing until it

drops into place.

Attaching the Fan Blades

Step 1 Attach blades to blade arms using three

screws with rubber washers.(Fig. 15) Start a

screw into the blade arm, do not tighten. Repeat

for the 2 remaining screws and washers.

Step 2 Tighten each screw securely starting

with the center screw. Make sure the blade is

straight. Repeat steps for the remaining blades.

Step 3

(Fig. 16)

Fasten the blade assemblies to the motor

housing by lining up the slots of the blade arms

with the tabs on the motor housing, then tighten

the two screws and washers already installed in

the blade arms.

WARNING

TO REDUCE THE RISK OF PERSONAL INJURY,

DO NOT BEND THE BLADE ARMS WHILE

INSTALLING, BALANCING THE BLADES, OR

CLEANING THE FAN. DO NO INSERT FOREIGN

OBJECTS BETWEEN ROTATING FAN BLADES.

Rubber packing

mounts

Screws

Figure 15

Figure 14

Figure 16

CAUTION: Remove 5 rubber packing

mounts from fan motor assembly and discard

before installation. (Fig. 14)

Motor

Blade arm

Slot

Tab

Blade

arm

Blade

Screws

with rubber

washer

This manual suits for next models

Table of contents

Other HAMPTON BAY Fan manuals

HAMPTON BAY

HAMPTON BAY EASTVALE User manual

HAMPTON BAY

HAMPTON BAY LEROY 37810 User manual

HAMPTON BAY

HAMPTON BAY ASHBURTON YG593-TB User manual

HAMPTON BAY

HAMPTON BAY Redington 740-125 User manual

HAMPTON BAY

HAMPTON BAY AL975-BN 593-552 User manual

HAMPTON BAY

HAMPTON BAY HAWKINS YG204-BN User manual

HAMPTON BAY

HAMPTON BAY CYPRUS 220 635 User manual

HAMPTON BAY

HAMPTON BAY TITAN 52 User manual

HAMPTON BAY

HAMPTON BAY Hawthorne II User manual

HAMPTON BAY

HAMPTON BAY Ansley User manual

HAMPTON BAY

HAMPTON BAY STANCE 52-STAN 52-STAN User manual

HAMPTON BAY

HAMPTON BAY CARROLTON II User manual

HAMPTON BAY

HAMPTON BAY GLENDALE III AK338-MBK User manual

HAMPTON BAY

HAMPTON BAY Metarie 795-970 User manual

HAMPTON BAY

HAMPTON BAY Altura 128 925 User manual

HAMPTON BAY

HAMPTON BAY Glendale 52 User manual

HAMPTON BAY

HAMPTON BAY Gazebo II YG187-WH User manual

HAMPTON BAY

HAMPTON BAY ST. DAVID 91344 User manual

HAMPTON BAY

HAMPTON BAY YG419-WH User manual

HAMPTON BAY

HAMPTON BAY Trusseau 324-683 User manual

HAMPTON BAY

HAMPTON BAY Torrington User manual

HAMPTON BAY

HAMPTON BAY AC457-WB User manual

HAMPTON BAY

HAMPTON BAY CEDAR LAKE 52109 User manual

HAMPTON BAY

HAMPTON BAY YG763-BN User manual

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual