HAMPTON BAY Antigua Plus User manual

56” Antigua Plus

Ceiling Fan by Hampton Bay

Accu-Arm™ for Accurate

and Easy Installation

Steeper Blade Pitch for

Greater Air Movement

3-Speed Reverse Function for

Year-Round Comfort and Savings

Tri-Mount Installation

QUESTIONS, PROBLEMS, MISSING PARTS:

Before returning to your local Home Depot, please call our

Customer Service Team at 1-877-527-0313 or visit www.homedepot.com.

Please reference your SKU (926 906 oil-rubbed bronze)

or UPC (082392 73540 1R oil-rubbed bronze).

Thank you for purchasing this Hampton Bay ceiling

fan. This product has been manufactured with the

highest standards of safety and quality. The nish

of this fan is weather resistant, but over time will

naturally weather and fade.

Safety Rules .................................. 1

Unpacking Your Fan .................... 2

Installing Your Fan ...................... 3

Operating Your Fan ..................... 10

Care of Your Fan.......................... 11

Troubleshooting............................ 11

Specications ................................ 12

Warranty Information................. 13

Table of Contents

UL Model No. 56-ANTHL

Safety Rules .................................. 1

Unpacking Your Fan .................... 2

Installing Your Fan ...................... 3

Operating Your Fan ..................... 10

Care of Your Fan.......................... 11

Troubleshooting............................ 11

Specications ................................ 12

Warranty Information................. 13

1. To reduce the risk of electric shock, insure electricity

has been turned off at the circuit breaker or fuse box

before beginning.

2. All wiring must be in accordance with the National

Electrical Code ANSI/NFPA 70-1999 and local electrical

codes. Electrical installation should be performed by a

qualied licensed electrician.

3. WARNING: To reduce the risk of re or electric shock, do

not use this fan with any solid-state speed control device.

4. CAUTION: To reduce the risk of personal injury, use only

the screws provided with the outlet box.

5. The outlet box and support structure must be securely

mounted and capable of reliably supporting a minimum of

35 pounds. Use only UL Listed outlet boxes marked “FOR

FAN SUPPORT.”

6. The fan must be mounted with a minimum of 7 feet

clearance from the trailing edge of the blades to the oor.

7. Do not operate reversing switch while fan blades are in mo-

tion. Fan must be turned off and blades stopped before re-

versing blade direction.

8. Avoid placing objects in path of the blades.

9. To avoid personal injury or damage to the fan and other items,

be cautious when working around or cleaning the fan.

10. Do not use water or detergents when cleaning the fan or fan

blades. A dry dust cloth or lightly dampened cloth will be

suitable for most cleaning.

11. After making electrical connections, spliced conductors

should be turned upward and pushed carefully up into

outlet box. The wires should be spread apart with the

grounded conductor and the equipment-grounding

conductor on one side of the outlet box.

12. Electrical diagrams are for reference only. Light kits that are

not packed with the fan must be UL listed and marked suitable

for use with the model fan you are installing. Switches must be

UL General Use Switches. Refer to the instructions packaged

with the light kits and switches for proper assembly.

Safety Rules 1.

READ AND SAVE THESE INSTRUCTIONS

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL

INJURY, MOUNT TO OUTLET BOX MARKED ACCEPTABLE FOR FAN

SUPPORT AND USE SCREWS PROVIDED WITH THE OUTLET BOX.

PLEASE REMOVE RUBBER MOTOR STOPS ON THE BOTTOM OF THE

FAN BEFORE INSTALLING BLADES OR TESTING THE MOTOR.

TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE

BLADE BRACKETS (ALSO REFERRED TO AS (“FLANGES”) DURING

ASSEMBLY OR AFTER INSTALLATION. DO NOT INSERT OBJECTS IN

THE PATH OF THE BLADES.

a. Blade attachment hardware

(15 screws)

b. Electrical Hardware

(3 plastic wire connectors, 1 hanger pin, 1

locking pin)

c. Close-to-Ceiling mount hardware

(1 rubber gasket)

d. Miscellaneous Parts & Balancing Kit

(2 pull chains, blade balancing kit)

8. Blade Bracket (Flange) Set (5)

with blade bracket screws pre-installed

9. Decorative Leaves

10. Light Kit

11. Glass Bowl

12. Bulbs (3)

1. Slide-On Mounting Plate (inside canopy)

2. Downrod and Hanger Ball Assembly

3. Canopy with Canopy Ring attached

4. Fan Motor Assembly

5. Switch Housing

6. Decorative Motor Collar Cover

7. Blades (5)

2. Unpacking Your Fan

IMPORTANT: THIS PRODUCTAND/OR COMPONENTSARE COVERED BY

ONE OR MORE OF THE FOLLOWING U.S. PATENTS: 5,947,436; 5,988,580;

5,971,573; 6,010,110; 6,010,306; 6,039,541; 6,046,416 AND OTHER

PATENTS PENDING.

Unpack your fan and check the contents. You should have the following items:

Installing Your Fan 3.

Tools Required

Phillips screw driver, straight slot screw

driver, adjustable wrench, step ladder, and

wire cutters.

Mounting Options

If there isn’t an existing outlet box, then read

the following instructions. Disconnect the

power by removing fuses or turning off

circuit breakers.

Secure the outlet box directly to the building

structure. Use appropriate fasteners and

building materials. The outlet box and its

support must be able to fully support the

moving weight of the fan (at least 35 lbs.)

Do not use plastic outlet boxes.

Figures 1, 2, and 3 are examples of different

ways to mount the outlet box.

Outlet Box

Note: You may need a longer downrod to

maintain proper blade clearance when install-

ing on a steep, sloped ceiling. The maximum

angle allowable is 30˚. If the canopy touches

downrod, remove the decorative canopy

bottom cover and turn the canopy 180˚ before

attaching the canopy to the mounting plate.

Outlet Box

To hang your fan where there is an existing

xture but no ceiling joist, you may need an

installation hanger bar as shown in Figure 4

(available at your Hampton Bay retailer).

TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK OR PERSONAL INJURY, MOUNT FAN

ONLY TO AN OUTLET BOX MARKED ACCEPT-

ABLE FOR FAN SUPPORT AND USE THE

MOUNTING SCREWS PROVIDED WITH THE OUT-

LET BOX. OUTLET BOXES COMMONLY USED

FOR THE SUPPORT OF LIGHTING FIXTURES

MAY NOT BE ACCEPTABLE FOR FAN SUPPORT

AND MAY NEED TO BE REPLACED. CONSULT A

LICENSED ELECTRICIAN IF IN DOUBT.

Figure 1

Figure 2

Figure 4

Figure 3

different procedures to follow for the two

types of installation.

Standard Ceiling Mounting

1. Remove the canopy ring from the canopy

by turning the ring to the right until it

unlocks (Figure 5).

2. Remove the mounting plate from the

canopy by loosening the four screws on

the top of the canopy. Remove the two

non-slotted screws and loosen the slotted

screws. This will enable you to remove the

mounting plate (Figure 6).

Hanging the Fan

REMEMBER to turn off the pow-

er. Follow the steps below to hang your

fan properly.

NOTE: This ceiling fan is supplied with two

types of hanging assemblies; the standard

ceiling installation using the downrod with

ball and socket mounting, and the “close-to-

ceiling” mounting. The “close-to-ceiling”

mounting is recommended in rooms with

less than 8-foot ceilings or in areas where

additional space is desired from the oor

to the fan blades. When using standard

downrod installation, the distance from the

ceiling to the bottom of the fan blades will be

approximately 12 inches. The “close-to-ceiling”

installation reduces the distance from the

ceiling to the bottom of the fan blades to

approximately 9 inches.

Once you have decided which ceiling

installation you will use, proceed with the

following instructions. Where necessary,

each section of the instructions will note the

Figure 5

Figure 6 Figure 7

3. Route the wires exiting the top of the

fan motor through the decorative motor

collar cover then the canopy ring. Make sure

the slot openings are on top. Route the wires

through the canopy and then through the

ball/downrod assembly (Figure 7).

WHEN MOUNTING THE FAN ON A SLOPED

CEILING, THE STANDARD BALL/DOWNROD

MOUNTING METHOD MUST BE USED. THE

MOUNTING PLATE MUST BE MOUNTED SO

THAT THE SLOT OPENINGS ARE ON THE

LOWER SIDE BY SLIDING THE MOUNTING

PLATE FROM THE TOP DOWN. FOR A GREATER

MOUNTING ANGLE, REMOVE THE DECORA-

TIVE CANOPY BOTTOM COVER (FIGURE 9).

“Close-to-Ceiling” Mounting

1. Remove the canopy ring from the canopy

by turning the ring to the right until it

unlocks (Figure 5).

2. Remove the mounting plate from the cano-

py by loosening the four screws on the top

of the canopy. Remove the two non-slotted

screws and loosen the slotted screws. This

will enable you to remove the mounting

plate (Figure 6).

3. Remove the decorative canopy bottom cov-

er from the canopy by depressing the three

studs (Figure 9).

4. Remove three of the six screws and lock-

washers (every other one) securing the mo-

tor collar to the top of the fan motor housing

(Figure 10).

5. Place the rubber gasket over the remain-

ing three screws, route the wires exiting

the top of the fan motor through the canopy

ring (make sure the slot openings are on

top), then proceed to place the ceiling can-

opy over the collar at the top of the motor

(Figure 11). 5.

4. Loosen, but do not remove, the set

screw on the collar on the top of the

motor housing.

5. Align the holes at the bottom of the

downrod with the holes in the collar

on top of the motor housing (Figure 7).

Carefully insert the hanger pin through

the holes in the collar and downrod. Be

careful not to jam the hanger pin against

the wiring inside the downrod. Insert the

locking pin through the hole near the

end of the hanger pin until it snaps into its

locked position, as noted in the circle inset

of Figure 7.

6. Re-tighten the set screws on the collar on top

of the motor housing (Figure 8).

7. Proceed to “Installing the Fan” section.

FAILURE TO PROPERLY INSTALL SET SCREWS

IN STEP 7 COULD RESULT IN FAN LOOSENING

AND POSSIBLY FALLING.

FAILURE TO PROPERLY INSTALL THE LOCK-

ING PIN AS NOTED IN STEP 5 COULD RESULT

IN FAN LOOSENING AND POSSIBLY FALLING.

Figure 8

Figure 9

Figure 10

Figure 11

6. Align the mounting holes with the holes

in the motor and fasten, using the three

screws and lock-washers removed in step 4

(Figure 11).

7. Tighten the mounting screws securely.

WHEN USING THE STANDARD BALL/DOWNROD

MOUNTING, THE TAB IN THE RING AT THE BOT-

TOM OF THE MOUNTING PLATE MUST REST IN

THE GROOVE OF THE HANGER BALL. FAILURE

TO PROPERLY SEAT THE TAB IN THE GROOVE

COULD CAUSE DAMAGE TO WIRING.

Installing Fan to

the Outlet Box

WHEN MOUNTING THE FAN ON A SLOPED

CEILING, THE STANDARD BALL/DOWNROD

MOUNTING METHOD MUST BE USED. MAKE

SURE THE MOUNTING BRACKET SLOTS ARE

ON THE LOWER SIDE BY SLIDING THE MOUNT-

ING BRACKET FROM THE TOP DOWN.

1. Pass the 120-volt supply wires through the

center hole in the ceiling mounting bracket

as shown in Figure 7.

2. Install the ceiling mounting plate on the out-

let box by sliding the mounting plate over

the two screws provided with the outlet

box. When using close-to-ceiling mount-

ing, it is important that the mounting plate

be level. If necessary, use leveling washers

(not included) between the mounting plate

and the outlet box. Note that the at side of

the mounting plate is toward the outlet box

(Figure 7).

3. Securely tighten the two mounting screws.

4. Carefully lift the assembly up to the ceil-

ing mounting plate. If using Close-to-

Ceiling mounting, hang the fan on the

hook provided by utilizing one of the

holes at the outer rim of the ceiling canopy

(Figure 12). If using standard mounting, seat

the hanger ball in the mounting plate socket.

Make sure the tab on the mounting bracket

socket is properly seated in the groove in the

hanger ball (Figure 12).

Figure 12

THE HOOK AS SHOWN IN FIGURE 12 IS ONLY

TO BALANCE FAN WHILE ATTACHING WIRING.

FAILURE TO HANG AS SHOWN IN FIGURE 12

MAY RESULT IN HOOK BREAKING, CAUSING

THE FAN TO FALL. HOOK MUST PASS FROM

INSIDE TO OUTSIDE OF CANOPY.

Making the Electrical

Connections

REMEMBER to disconnect the power. If

you feel you do not have enough electrical

wiring knowledge or experience, have your fan

installed by a licensed electrician.

Follow the steps below to connect the fan

to your household wiring. Use the wire

connecting nuts supplied with your fan. Se-

cure the connectors with electrical tape.

Make sure there are no loose strands or

connections.

1. Connect the two green fan ground wires lo-

cated on the downrod and mounting plate

to the household ground wire. When using

Close-to-Ceiling mounting, there is only one

green ground wire from the ceiling mount-

ing plate since the ball/downrod assembly is

not used.

2. Connect the fan light supply (blue) wire

and the fan supply (black) wire to the

black household supply wire as shown in

gure 13.

3. Connect the neutral fan (white) wire to the

white neutral household wire.

4. After connecting the wires, spread them

apart so that the green and white wires are

on side of the outlet box and the black wire

is on the other side.

5. Turn the wire connecting nuts upward and

push the wiring into the outlet box.

EACH WIRE NUT (WIRE CONNECTOR) SUP-

PLIED WITH THIS FAN IS DESIGNED TO ACCEPT

UP TO ONE 12 GAUGE HOUSE WIRE AND TWO

WIRES FROM THE FAN. IF YOU HAVE LARGER

THAN 12 GAUGE HOUSE WIRING OR MORE

THAN ONE HOUSE WIRE TO CONNECT TO THE

FAN WIRING, CONSULT AN ELECTRICIAN FOR

THE PROPER SIZE WIRE NUTS TO USE.

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT USE A WALL MOUNTED SOLID

STATE SPEED CONTROL WITH THIS FAN. IT

WILL PERMANENTLY DAMAGE THE ELEC-

TRONIC CIRCUITRY.

Figure 13

Finishing the Fan

Installation

STANDARD CEILING MOUNTING

1. Align the locking slots of the ceiling canopy

with the two screws in the mounting plate.

Push up to engage the slots and turn clock-

wise to lock in place. Immediately tighten

the two mounting screws rmly.

2. Install the remaining two mounting

screws into the holes in the canopy and

tighten rmly.

3. Install the decorative canopy ring by align-

ing the ring’s slots with the screws in the

canopy. Rotate the ring clockwise to lock

in place.

4. You may now proceed to attaching the

fan blades.

WHEN USING THE STANDARD BALL/DOWNROD

MOUNTING, THE TAB IN THE RING AT THE BOT-

TOM OF THE MOUNTING PLATE MUST REST IN

THE GROOVE OF THE HANGER BALL. FAILURE

TO PROPERLY SEAT THE TAB IN THE GROOVE

COULD CAUSE DAMAGE TO WIRING.

Figure 15

CLOSE-TO-CEILING MOUNTING

1. Carefully unhook the fan from the mount-

ing plate and align the locking slots of the

ceiling canopy with the two screws in the

mounting plate. Push up to engage the slots

and turn clockwise to lock in place. Imme-

diately tighten the two mounting screws

rmly.

2. Install the remaining two mounting screws

into the holes in the canopy and tighten

rmly.

3. Install the decorative canopy ring by align-

ing the ring’s slots with the screws in the

canopy. Rotate the ring clockwise to lock

in place.

4. You may now proceed to attaching the fan

blades.

Attaching the

Fan Blades

1. Attach blade to blade bracket using the

screws as shown in gure 14. Please note that

the rubber washers are pre-attached to the

blade bracket. Start a screw into the bracket.

Repeat for the two remaining screws.

LOCKING SLOTS OF CEILING CANOPY ARE

PROVIDED ONLY AS AN AID TO MOUNTING.

DO NOT LEAVE FAN ASSEMBLY UNATTENDED

UNTIL ALL FOUR CANOPY SCREWS ARE EN-

GAGED AND FIRMLY TIGHTENED.

2. Tighten each screw securely.

3. Fasten the blade assembly to the motor by

inserting the alignment post into the slot on

the bottom of the motor and tightening the

blade bracket screws. Please note that the

blade bracket screws are pre-installed into

the blade bracket (Figure 14a).

4. Repeat steps 1-3 for the remaining blades.

Figure 14

Figure 14a

Blade Balancing

All blades are grouped by weight. Because nat-

ural woods vary in density, the fan may wobble

even though the blades are weight matched. The

following procedure should correct most fan

wobble. Check after each step.

1. Check that all blade and blade bracket

screws are secure.

2. Most fan wobble problems are caused when

Attaching the

Switch Housing

1. Remove the three mounting screws on the

black bracket below the motor (Figure 15).

2. Connect the adaptor plug exiting the bottom

of the motor with the plug from the switch

housing.

3. Mount the switch housing to the black plate

below the motor by aligning the three screw

holes and securing with the three screws re-

moved in step 1.

Screws

Molded

Adaptor

Connector

Switch

Housing

Black

Bracket

Other manuals for Antigua Plus

Table of contents

Other HAMPTON BAY Fan manuals

HAMPTON BAY

HAMPTON BAY Gazebo II YG187-WH User manual

HAMPTON BAY

HAMPTON BAY Landmark Plus User manual

HAMPTON BAY

HAMPTON BAY STONERIDGE EF600K-52 User manual

HAMPTON BAY

HAMPTON BAY YG269AP-MWH User manual

HAMPTON BAY

HAMPTON BAY 68144 User manual

HAMPTON BAY

HAMPTON BAY GAZEBO YG188-BN User manual

HAMPTON BAY

HAMPTON BAY MIDILI 91100 User manual

HAMPTON BAY

HAMPTON BAY GAZEBO II YG188-WH User manual

HAMPTON BAY

HAMPTON BAY PORTSMOUTH 51355 User manual

HAMPTON BAY

HAMPTON BAY 266-848 Installation guide

HAMPTON BAY

HAMPTON BAY AM212INL-WH User manual

HAMPTON BAY

HAMPTON BAY AG524-ORB User manual

HAMPTON BAY

HAMPTON BAY Y52YH5-06 Owner's manual

HAMPTON BAY

HAMPTON BAY 68" Enchantment User manual

HAMPTON BAY

HAMPTON BAY 58919 User manual

HAMPTON BAY

HAMPTON BAY 855975 User manual

HAMPTON BAY

HAMPTON BAY 7114-01 User manual

HAMPTON BAY

HAMPTON BAY Brookedale II User manual

HAMPTON BAY

HAMPTON BAY 567-472 User manual

HAMPTON BAY

HAMPTON BAY BANNERET YG730-MWH User manual

HAMPTON BAY

HAMPTON BAY AM217-BK User manual

HAMPTON BAY

HAMPTON BAY Tipton II 52" User manual

HAMPTON BAY

HAMPTON BAY AL958B-BN User manual

HAMPTON BAY

HAMPTON BAY 52119 User manual

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual