HAMPTON BAY 476-317 User manual

Hampton Bay Lifetime Limited Warranty

The retailer warrants the fan motor to be free from defects in workmanship and material

present at time of shipment from the factory for a lifetime after the date of purchase by the

original purchaser. The retailer also warrants that all other fan parts, excluding any glass or

plexiglass blades, to be free from defects in workmanship and material at the time of

shipment from the factory for a period of one year after the date of purchase by the original

purchaser. We agree to correct such defects without charge or at our option replace with a

comparable or superior model if the product is returned to the retailer. To obtain warranty

service, you must present a copy of the receipt as proof of purchase. All costs of removing

and reinstalling the product are your responsibility. Damage to any part such as by accident

or misuse or improper installation or by affixing any accessories, is not covered by this

warranty. Because of varyingclimatic conditions inthe United States this warranty does not

cover any changesin brass finish, including rusting, pitting, corroding, tarnishing orpeeling.

Brass finishes of this type give their longest useful life when protectedfrom varying weather

conditions. A certain amount of wobble is normal and should not be considered a defect.

Servicing performed by unauthorized persons shallrender the warranty invalid. There is no

other express warranty. The retailer hereby disclaims any and all warranties,

including but not limited to. Those of merchantability and fitness for a particular

purpose to the extent permitted by law. The duration of any implied warranty which

cannot be disclaimedis limited to the time period as specified inthe express warranty. Some

states do not allow limitation on how long an implied warranty lasts, so the above limitation

may not apply to you. The retailer shall not be liable for incidental, consequential, or

special damages arising out of or in connection with product use or performance except

as may otherwise be accorded by law. Some states do not allow theexclusion of incidental

or consequential damages, so the above exclusion or limitation may not apply to you. This

warranty gives specific legal rights, and you may also have other rights which vary from

state to state. This warranty supersedes all priorwarranties.

Lifetime Limited Warranty

Date Purchased

Store Purchased

Model No.

Serial No.

Vendor No.

UPC

476-317

11289

792145350705

Safety Rules.....................................................................................................................................

Unpacking Your Fan ........................................................................................................................

Installing Your Fan ...........................................................................................................................

Installing the Light Kit.....................................................................................................................

Operating Your Fan .........................................................................................................................

Care of You r Fan ...........................................................................................................................

Troubleshooting ............................................................................................................................

Specifications ...............................................................................................................................

10.

11.

12.

13.

14.

Table of Contents

1. To reduce the risk of electric shock, insure electricity has been turned

off at the circuit breakeror fuse boxbefore beginning.

2. All wiring must be in accordance with the National Electrical Code and

local electrical codes. Electrical installation should be performed by a

qualified licensed electrician.

3. WARNING: To reduce the risk of electrical shock and fire, do not use

this fan withany solid-state fanspeed control device.

4. WARNING: To reduce the riskof personal injury, use only the two steel

screws (and lock washers) provided with the outlet box for mounting to

the outlet box. Most outlet boxes commonly used for the support of

lighting fixtures are not acceptable for fan support and may need to be

replaced, consult aqualified electrician ifin doubt.

7. Do not operate reversing switch while fan blades are in motion. Fan

must be turned off and blades stopped before reversing blade

direction.

8. Avoid placing objects in the path of the blades.

9. To avoid personal injury or damage to the fan and other items, be

cautious when workingaround or cleaningthe fan.

10. Do not use water or detergents when cleaning the fan or fan blades. A

dry dust cloth or lightly dampened cloth will be suitable for most

cleaning.

11. After marking electrical connections, spliced conductors should be

turned upward and pushed carefully up into outlet box. The wires

should be spread apart with the grounded conductor and the

equipment-grounding conductor onone side ofthe outlet box.

12. Electrical diagrams are for reference only. Light kit that are not

packed with the fan must be UL Listed and marked suitable for use

with the model fan you are installing. Switches must be UL General

Use Switches. Refer to the Instructions packaged with the light kits

and switches forproper assembly.

WARNING

TO REDUCETHE RISK OFFIRE, ELECTRIC SHOCKOR PERSONAL

INJURY, MOUNT FAN TO OUTLET BOX MARKEDACCEPTABLE FOR

FAN SUPPORT.

5. The outlet box and support structure must be securely mounted and

capable of reliably supporting a minimum of 50 pounds. Use only UL

Listed outlet boxesmarked FOR FAN SUPPORT.

6. The fan must be mounted with a minimum of 7 feet clearance from the

trailing edge ofthe blades tothe floor.

WARNING

TO REDUCETHE RISK OFPERSONAL INJURY, DO NOTBEND THE

BLADE BRACKETS (ALSOREFERRED TOAS FLANGES)DURING

ASSEMBLYOR AFTERINSTALLATION. DO NOTINSERT OBJECTS IN

THE PATHOF THE BLADES.

NOTE

READ AND SAVE ALLINSTRUCTIONS!

1. Safety Rules

Unpacking Your Fan 2.

Unpack your fanand check thecontents. You should havethe following items:

2. Canopy assembly

Set of blades(5)

Ball/downrod assembly

Collar cover

Fan motor assembly

6. Set ofblades arms (5)

7. Light fixture

Pull chains andfobs (2)

60Watt medium base bulbs (2)

8. Glass shade

10.

11. Balancekit

12. Loose partsbag containing:

a. Blade attachmenthardware

(16 screws)

b. Mounting hardware

(3 plastic wireconnectors)

c. Flush mountingattachment

hardware

(3 screws &3 lock washers)

WARNING

DO NOT INSTALL ORUSE FAN

IF ANYPARTIS DAMAGED OR MISSING.

CALL TOLLFREE 877-898-1881

NOTE

FOR NON-LIGHT USEPURPOSE, THE

SWITCH HOUSING COVERIS AVAILABLE

BY CALLINGTHE TOLLFREE NUMBER

877-898-1881

3. Installing Your Fan

Tools Required

Phillips screwdriver, straight slot

screwdriver, adjustablewrench, step ladder,

and wire cutters.

Mounting Options

If there isn't an existing ULlisted mounting

box, then read the following instructions.

Disconnect the power by removing fuses or

turning off circuit breakers.

Secure the outlet box directly to the

building structure. Use appropriate

fasteners and buildingmaterials. The outlet

box and its support must be able to fully

support the moving weight of the fan (at

least 50 lbs). Do not use plastic outlet

boxes.

Figures 1,2 and 3 are examples of different

ways to mountthe outlet box.

Note: You may need a longer downrod to

maintain proper blade clearance when

installing on asteep, sloped ceiling.

To hang your fan where there is an existing

fixture but no ceiling joist, you may need an

installation hanger bar as shown in Figure 4

(available at yourHampton Bay Retailer).

Outlet box

Provide strong

support

Recessed

outlet box

Mounting bracket

opening must be

toward the top

Outlet box

Figure 1 Figure 3

Figure 2

Figure 4

Angled ceiling

maximum

20 angle

Hanging the Fan

REMEMBER to turn off th the power. Follow

the steps below to hangyour fan properly. NOTE:

This ceiling fan is supplied with two types of

hanging assemblies; the standard ceiling

installation using the downrod with ball and

socket mounting and the "close-to-ceiling"

installation. The "close-to-ceiling" installation

is recommended in rooms with less than 8-feet

ceilings or in areas where additional space is

desired from the floor to the fan blades. When

using the standard 4 1/2"downrod, the distance

from the ceiling to the bottom of the fan blades

will be approximately 12 inches. The "close-

to-ceiling" installation reduce this distanceto 8-

inches. Once you have selected which mounting

system you will use, proceed with the following

instructions. Where necessary, each section of

the instructions will note the different

procedures to follow for the two types of

mounting.

1/2

STANDARD CEILINGINSTALLATION

1. Remove the canopy ring from the canopy by

turning the ring to the right until it unlocks.

(Fig. 5)

2. Remove the hanger bracket from the canopy by

loosening the four screws onthe top of the canopy.

Remove the two non-slotted screws and loosen

the slotted screws. This will enable you to

remove the hanger bracket. (Figure5)

9. Align theholes at the bottom ofthe downrod with

the holes in the collaron top of the motorhousing

(Figure 6A). Carefully insert the hanger pin

through the holes in the collar and downrod. Be

careful not to jam thepin against the wiring inside

the downrod. Insert the locking pin through the

hole in locked position, asnoted in the circle inset

of Figure 6A

WARNING

FAILURETO PROPERLY INSTALL LOCKING

PIN AS NOTEDIN STEP 9COULD RESULT IN

FAN LOOSENINGAND POSSIBLY FALLING.

3. Pass the 120-volt supplywires through the center

hole in the ceiling hanger bracket as shown in

Fig.6

4. Loose the two screwson the outlet box inhalf way.

5. Attach the hanger bracket on the outlet box by

sliding the hanger bracket over the screws

provided with the outlet box.

6.Tighten the two screwson the outlet box securely.

7. Remove the hanger pin, locking pin and set

screws from the top ofthe motor assembly.

8. Route wires exiting fromthe top of the fan motor

through the collar cover and canopy ring. Make

sure the slot openings of the canopy ring are on

top. Route the wires through the canopy andthen

through the ball/downrod assembly (Figure6A).

Figure 5

Ceiling

mounting

plate

Ceiling

canopy

Screws

Canopy

ring

Mounting

screws

(supplied with

electrical box)

Tab

Ceiling

mounting

plate

UL Listed

electrical

box

Slide mounting

bracket over

screw heads

Figure 6 120V Wires

CAUTION

REMOVE 4 RUBBERPACKING MOUNTS

AND DISCARD BEFOREINSTALLATION.

10. Tighten two set screws on top of the fan

motor firmly.(Figure 6A)

11. Place the downrod ball into the hanger

bracket socket.

4. Pass the 120-volt supply wires through the center

hole in the ceiling hanger bracket as shown in Fig.

5. Loose the two screws on the outlet box halfway.

6. Attach the hanger bracket on the outlet box by

sliding the hanger bracket over the screws provided

with the outlet box.

7. Tighten the two screws on the outlet box securely.

8. Remove three of the six screws and lock washers

(every other one) from the collar of top motor

(Figure. 7)

9. Place the rubber gasket over the remaining three

screws, route the wires exiting the top of the fan

motor through the canopy ring (make sure the slot

openings of the ring are on top). then proceed to

place the ceiling canopy over the collar at the top

of the motor. Align the mounting holes with the

holes in the motor and fasten using the screws and

lock washers provided (Fig. 7).

10.Tighten the mounting screws securely. (Fig. 7)

11.Hang the fan on the tab of the hanger bracket. Be

certain that the canopy is fully locked into tab as

shown in Fig. 8. This will allow you to make the

electrical connections.

Pin in

locked

position

Canopy ring

Hanger pin

Motor collar

Motor wires

Ball/downrod

assembly

Ceiling

canopy

Locking pin

Tighten

screws

firmly

Figure 6A

Collar cover

Figure 8

Tab

Figure 7A

Canopy

Bottom

Cover

Screw and

Lockwasher

(3 of 6 places)

Ceiling

Canopy

Figure 7

Canopy

Ring

Collar

Rubber

gasket

CLOSE-TO-CEILING INSTALLATION

1. Remove the canopy ring from the

canopy by turning the ring to the right

until it unlocks. (Fig. 5)

2. Remove the hanger bracket from the

canopy by loosening the four screws

on the top of the canopy. Remove the

two non-slotted screws and loosen the

slotted screws. This will enable you to

remove the hanger bracket. (Figure5)

3. Remove the decorative canopy bottom

cover from the canopy by depressing

the three studs (Fig. 7A)

WARNING

FAILURE TOCOMPLETELYTIGHTEN

THE THREE SCREWS IN STEP9 COULD RESULT IN

FAN LOOSENINGAND POSSIBLY FALLING.

Making the Electrical

Connections

Remember to disconnect the power.

Follow the steps below to connect the fan to your household

wiring. Use the wire connecting nuts supplied with your fan.

Secure the connectors with electrical tape. Make sure there are

no loose strands or connections.

Step 1 Connect the fan supply (black) wire and light supply (blue)

wire to the black household supply wire as shown in Figure 9.

Step 2. Connect the neutral fan (white) wire to the white neutral

household wire.

Step 3 Connect the fan ground wire (green) to the household

ground wire.

Step 4 After connecting the wires, spread them apart so that the

green and white wires are on one side of the outlet box and the

black and the blue wires are on the other side.

Step 5 Turn the connecting nuts upward and push the wiring into

the outlet box.

Figures 10 and 11 illustrate the wiring connections for optional

wall control (available at your Hampton Bay Retailer, the wire

color out of wall control may vary, see wall control's installation

manual for correct wire connections.)

NOTE

LIGHT KITS ARE AVAILABLE AT YOU

HAMPTON BAYRETAILER. THE FAN IS

ALREADY WIRED TO SUPPORT THE LIGHT KIT OPTION.

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR

OTHER PERSONAL INJURY. MOUNT FAN ONLY ON AN

OUTLET BOX OR SUPPORTING SYSTEM MARKED

ACCEPTABLE FOR FAN SUPPORT.

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK.

DO NOT USE THIS FAN WITH ANYSOLID-STATE SPEED

CONTROL DEVICE.

SUPPLYCIRCUIT

Ground

Conductor

Outlet Box

Green

Ground

Lead

Ground to

Downrod

BLACK

WHITEWHITE

BLACK

BLUE

GREEN

WHITE

BLUE

BLACK WHITE

Figure 9

Diagram indicates optionallight kit wiring.

SUPPLYCIRCUIT

Ground

Conductor

Outlet Box

Green

Ground

Lead

Ground to

Downrod

BLACK

WHITE

BLACK

BLUE

GREEN

Figure 10

Diagram indicates optionallight kit wiring.

Light Switch

WHITE

BLUE

BLACK WHITE

Finishing the

Installation

STANDARD CEILINGINSTALLATION

Slide canopy up to the ceiling as shown in

Figure 12 leaving a 1/8" clearance

between the canopy and the ceiling. Make

sure you place the wires safely into outlet

box. Secure the canopy to the hanger

bracket with thefour screws withyour fan.

Slide the canopy ring over the canopy and

tighten by turningthe ring.

CLOSE-TO-CEILING INSTALLATION

Remove the fan from the tab on the hanger

bracket. Secure the canopy to the hanger

bracket as shown in Figure 13 with four

screws included with your fan. Slide the

canopy ring over the canopy and tighten

by turning thering.

Figure 12

Figure 13

Allow 1/8"

Clearance

Allow 1/8"

Clearance

SUPPLYCIRCUIT

Ground

Conductor

Outlet Box

Green

Ground

Lead

Ground to

Downrod

BLACK

WHITE

BLACK

BLUE

GREEN

Figure 11

Diagram indicates optionallight kit wiring.

Light

Fan

WHITE

BLUE

BLACK WHITE

Remove the blade attachment screws from

the fan motor assembly. Attach and adjust

fan blades according to the instructions in

the following section.

WARNING

Make sure thenotch on thehanging

bracket properly sitsin the groovein the

hanger ball beforeattaching the canopy

to the bracketby turning thehousing

until it dropsinto place.

Rubber

washer

Blade

arm

Figure 14

Blade

Screws

Attaching the Fan

Blades

Step 1 Attach the blades to the blade arms

using three screws and rubber washers as

shown in Figure 14. Start a screw into the arm,

do not tighten. Repeat for the 2 remaining

screws and washers.

Step 2 Tighten each screw securely starting

with the center screw. Make sure the blade is

straight.

Step 3 Fasten the blade arms to the motor by

inserting the tab from the blade arms to the slot

in the bottom motor housing, then tighten the

two screws and washers already installed in the

blade arms (Figure15).

Step 4 Install an optional light kit if you wish.

Follow the instructionsincluded with the kit.

Figure 15

Motor

Blade arm

Slot

Tab

Table of contents

Other HAMPTON BAY Fan manuals

HAMPTON BAY

HAMPTON BAY Miramar User manual

HAMPTON BAY

HAMPTON BAY 290-286 User manual

HAMPTON BAY

HAMPTON BAY SAUTERNE AL975-BN User manual

HAMPTON BAY

HAMPTON BAY BPT13-13D-1 User manual

HAMPTON BAY

HAMPTON BAY YG269AP-MWH User manual

HAMPTON BAY

HAMPTON BAY Bercello Estates II User manual

HAMPTON BAY

HAMPTON BAY ASHBURTON YG593-BN User manual

HAMPTON BAY

HAMPTON BAY MINNA HE-12026 User manual

HAMPTON BAY

HAMPTON BAY AL958B-BN User manual

HAMPTON BAY

HAMPTON BAY 24816-021 User manual

HAMPTON BAY

HAMPTON BAY Antigua Plus User manual

HAMPTON BAY

HAMPTON BAY ALTURA 52356 User manual

HAMPTON BAY

HAMPTON BAY GAZEBO II YG188-WH User manual

HAMPTON BAY

HAMPTON BAY CHASTAIN II User manual

HAMPTON BAY

HAMPTON BAY PORTSMOUTH 51355 User manual

HAMPTON BAY

HAMPTON BAY STONERIDGE EF600K-52 User manual

HAMPTON BAY

HAMPTON BAY GLENDALE AG524-FB User manual

HAMPTON BAY

HAMPTON BAY YG098-NM User manual

HAMPTON BAY

HAMPTON BAY SW19129-A ORB User manual

HAMPTON BAY

HAMPTON BAY ASHBURTON YG593-WH User manual

HAMPTON BAY

HAMPTON BAY BAYFIELD User manual

HAMPTON BAY

HAMPTON BAY OSCW-24M BK User manual

HAMPTON BAY

HAMPTON BAY SEAPORT AL634-WH User manual

HAMPTON BAY

HAMPTON BAY SFZ-500-1 User manual

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual