HAMPTON BAY 284-485 User manual

Hampton Bay Lifetime Limited Warranty

The retailer warrants the fan motor to be free from defects in workmanship and material

present at time of shipment from the factory for a lifetime after the date of purchase by the

original purchaser. The retailer also warrants that all other fan parts, excluding any glass or

plexiglass blades, to be free from defects in workmanship and material at the time of

shipment from the factory for a period of one year after the date of purchase by the original

purchaser. We agree to correct such defects without charge or at our option replace with a

comparable or superior model if the product is returned to the retailer. To obtain warranty

service, you must present a copy of the receipt as proof of purchase. All costs of removing

and reinstalling the product are your responsibility. Damage to any part such as by accident

or misuse or improper installation or by affixing any accessories, is not covered by this

warranty. Because of varyingclimatic conditions inthe United States this warranty does not

cover any changesin brass finish, including rusting, pitting, corroding, tarnishing orpeeling.

Brass finishes of this type give their longest useful life when protectedfrom varying weather

conditions. A certain amount of wobble is normal and should not be considered a defect.

Servicing performed by unauthorized persons shallrender the warranty invalid. There is no

other express warranty. The retailer hereby disclaims any and all warranties,

including but not limited to. Those of merchantability and fitness for a particular

purpose to the extent permitted by law. The duration of any implied warranty which

cannot be disclaimedis limited to the time period as specified inthe express warranty. Some

states do not allow limitation on how long an implied warranty lasts, so the above limitation

may not apply to you. The retailer shall not be liable for incidental, consequential, or

special damages arising out of or in connection with product use or performance except

as may otherwise be accorded by law. Some states do not allow theexclusion of incidental

or consequential damages, so the above exclusion or limitation may not apply to you. This

warranty gives specific legal rights, and you may also have other rights which vary from

state to state. This warranty supersedes all priorwarranties.

Lifetime Limited Warranty

Date Purchased

Store Purchased

Model No.

Serial No.

Vendor No.

UPC

284-485

219032

792145350378

Safety Rules.....................................................................................................................................

Unpacking Your Fan .........................................................................................................................

Installing Your Fan ...........................................................................................................................

Installing the Light Kit......................................................................................................................

Your .............................................................................................................

Care of Your Fan .............................................................................................................................

Troubleshooting .............................................................................................................................

Specifications ................................................................................................................................

Operating Transmitter

10.

11.

12.

13.

Table of Contents

1. Safety Rules

1. To reduce the risk of electric shock, insure electricity has been turned

off at the circuit breakeror fuse boxbefore beginning.

2. Allwiring must bein accordance with the National Electrical Code and

local electrical codes. Electrical installation should be performed by a

qualified licensed electrician.

3. WARNING: To reduce the risk of electrical shock and fire, do not use

this fan withany solid-state fanspeed control device.

4. WARNING: To reduce the risk of personal injury, use only the two

steel screws (and lock washers) provided with the outlet box for

mounting to the outlet box. Most outlet boxes commonly used for the

support of lighting fixtures are not acceptable for fan support and may

need to bereplaced, consult aqualified electrician ifin doubt.

8. Avoid placing objects in the path of the blades.

9. To avoid personal injury or damage to the fan and other items, be

cautious when workingaround or cleaningthe fan.

10. Do not use water or detergents when cleaningthe fan or fan blades. A

dry dust cloth or lightly dampened cloth will be suitable for most

cleaning.

11. After making electrical connections, spliced conductors should be

turned upward and pushed carefully up into the outlet box. The wires

should be spread apart with the grounded conductor and the

equipment-grounding conductor onone side ofthe outlet box.

12. Electrical diagrams are for reference only. Light kits that are not

packed with the fan must be UL Listed and marked suitable for use

with the model fan you are installing. Switches must be UL General

Use Switches. Refer to the Instructions packaged with the light kits

and switches forproper assembly.

WARNING

TO REDUCETHE RISK OFFIRE, ELECTRIC SHOCKOR PERSONAL

INJURY, MOUNT FAN TO OUTLET BOX MARKEDACCEPTABLE FOR

FAN SUPPORT.

5. The outlet box and support structure must be securely mounted and

capable of reliably supporting a minimum of 50 pounds. Use only UL

Listed outlet boxesmarked FOR FAN SUPPORT.

6. The fan must be mounted with a minimum of 7 feet clearance from the

trailing edge ofthe blades tothe floor.

7. Do not operate the reverse switch while the fan blades are in motion.

The fan must be turned off and the blades stopped before reversing the

blades direction.

WARNING

TO REDUCETHE RISK OFPERSONAL INJURY, DO NOTBEND THE

BLADE ARMS(ALSO REFERRED TO ASBRACKETS) DURING

ASSEMBLYOR AFTERINSTALLATION. DO NOTINSERT OBJECTS IN

THE PATHOF THE BLADES.

NOTE

READ AND SAVE ALLINSTRUCTIONS!

Unpacking Your Fan 2.

Unpack your fanand check thecontents. You should havethe following items:

2. Canopy assembly

Set of blades(5)

Ball/downrod assembly (1)

& extra downrod(1)

Collar cover

5. Glass plate(2)

6. Fan motorassembly

7. Top glass shade

8. Set ofblade arms (5 )

10. Bottom glassshade

11. Finial

Receiver+6 wire nuts

Transmitter+holder+2 mounting screws

candelabra

Balancing kit

. Light kit

12.

13.

14. 15

16.

W Bulbs (6)

15. 40W Bulbs (3)

17. Loose partsbag containing:

a. Blade attachmenthardware

()

b. Mounting hardware

( 3 plasticwire connectors)

16 screws

WARNING

DO NOT INSTALL ORUSE FAN

IF ANYPARTIS DAMAGED OR MISSING.

CALL TOLLFREE 1-877-898-1881

ONON

UPLIGHT

DOWNLIGHT

LO MED HI

FANOFF

3. Installing Your Fan

Tools Required

Phillips screwdriver, straight slot

screwdriver, adjustablewrench, step ladder,

and wire cutters.

Mounting Options

If there isn't an existing ULlisted mounting

box, then read the following instructions.

Disconnect the power by removing fuses or

turning off circuit breakers.

Secure the outlet box directly to the

building structure. Use appropriate

fasteners and buildingmaterials. The outlet

box and its support must be able to fully

support the moving weight of the fan (at

least 50 lbs). Do not use plastic outlet

boxes.

Figures 1,2 and 3 are examples of different

ways to mountthe outlet box.

Note: You may need a longer downrod to

maintain proper blade clearance when

installing on asteep, sloped ceiling.

To hang your fan where there is an existing

fixture but no ceiling joist, you may need an

installation hanger bar as shown in Figure 4

(available at yourHampton Bay Retailer).

Outlet box

Provide strong

support

Recessed

outlet box

Mounting bracket

opening must be

toward the top

Outlet box

Figure 1 Figure 3

Figure 2

Figure 4

Angled ceiling

maximum

20 angle

Hanging the Fan

REMEMBER to turn off the power. Follow

the steps belowto hang yourfan properly:

Step 1. Remove the decorative canopy

bottom cover from the canopy by turning the

cover counter clockwise.(Fig.6)

Step 2. Remove the hanger bracket from the

canopy by loosening the two screws on the

bottom of the hanging bracket turn

from the screw head and turning the canopy

counter clockwise.(Fig, 6)

Step 3. Pass the 120-volt supply wires

through the center hole in the ceiling hanger

bracket as shownin Fig.7.

Step 4. Secure the hanger bracket to the

ceiling outlet box with the screws and

washers provided withyour outlet box.

Step 5. Remove the hanger pin, lock pin and

set screws from the top of the motor

assembly.

Step 6. Route wires exiting from the top of

the fan motor through the collar cover,

canopy cover, canopy and then through the

ball / downrod.(Fig. 8)

Step 7. Align the holes at the bottom of the

downrod with theholes in the collar on topof

the motor housing (Fig.8). Carefully insert

a half

WARNING

FAILURETO PROPERLY INSTALL LOCKINGPIN

AS NOTED INSTEP 7 COULD RESULT IN FAN

LOOSENING ANDPOSSIBLYFALLING.

Step 8. Tighten twoset screws ontop of the fan

motor firmly (Figure8)

Step 9. Place the downrod ball into the hanger

bracket socket.

CHANGING THE DOWNROD(OPTIONAL)

NOTE: Your fan comes with a 4" downrod

attached to the hanger ball. In addition you

have been provided with a 6"downrod to use if

desired. If you choose to use the 6" downrod,

perform the followingsteps:

1. Remove the hanger ball from the 4"

downrod by loosening the set screw at the

top of the downrod which holds the hanger

ball to thedownrod.

2. Slide the hanger ball down the downrod and

remove the supportpin.

the hanger pin through the holes in the collar

and downrod. Be careful not to jam the pin

against the wiring inside the downrod. Insert

the locking pin through the hole near the end

of the hanger pin until it snaps into its locked

position, as notedin the circleinset of Fig. 8.

Figure 5

Installing the bulbs

and glass plate

Step 1. Install 6 x15W bulbs (provided) into

the sockets of the bulb holder bracket on the

top of motor,

Step 2. Loose the four thumb screws and

rubber washers from the bulb holder bracket.

Step 3. Place the two glass plates over the bulb

holder bracket and secure them in place with

the four thumb screws and rubber washers

previously removed. Tighten the thumb screws,

DO NOT OVER TIGHTEN.

Glass plate

Bulb holder bracket

Bulbs

Thumb screw

Rubber washer

Make the Electric Connections

WARNING: To avoid possible electrical

shock, be sureelectricity is turned off at the

main fuse boxbefore wiring.

NOTE: This remote control unit is

equipped with 16 code combinations to

prevent possible interference from or to

other remote units. The frequency switches

on your receiver and transmitter have been

preset at the factory. Please recheck to

make sure the switches on transmitter and

receiver are set to the same position, any

combination of settings will operate the fan

as long as the transmitter and receiver are

set to thesame position.(Figure 9)

Step 1. (Figure 10) Insert the receiver into

the mounting bracket with the flat side of

the receiver facingthe ceiling.

Step 2. (Figure 11) Motor to Receiver

Electrical Connections: Connect the Black

wire from the fan to Black wire marked "TO

MOTOR L". Connect the White wire from

the fan to the White wire marked "TO

MOTOR N" from the receiver. Connect the

Blue wire fromthe fan to the Blue wiremarked

"For bottom Light" from the receiver.

Connect the Orange wire from fan to the

Orange wire from receiver marked "For

Upper Light". Secure wire connections with

the plastic wire nuts provided. Wire nuts

provided.

Step 3. (Figure 11) Receiver to House Supply

Wires Electrical Connections: Connect the

black (hot) wire from the ceiling to the black

wire marked "AC in L" from the receiver.

Connect the white(neutral) wire from the

ceiling to the white wire marked "AC in N"

from the Receiver. Secure the wire

connections with the plastic wire nuts

provided.

Step 4. (Figure 11) If your outlet box has a

ground wire (green or bare copper) connect it

To the fan ground wires; otherwise connect

the hanging bracket ground wire to the

mounting bracket. Secured the wire

connection with a plastic nut provided. After

connecting the wires spread them apart so

that the green and white wires are on one side

of the outlet box and black and blue wires are

on the other side. Carefully tuck the wire

connections up into the outlet box.

Pin in

locked

position

Motor collar

Motor wires

Ball/downrod

assembly

Ceiling

canopy

Tighten

screws

firmly

Figure 8

Hanger pin

Locking pin Collar cover

Canopy

cover

Figure 6

Ceiling

mounting

plate

Ceiling

canopy

Canopy

cover

Mounting

screws

(supplied with

electrical box)

Hook

Ceiling

mounting

plate

UL Listed

electrial

box

Figure 7 120V Wires

Washers

3. Insert the support pin in the holes at the

top of the 6" downrod and slide the

hanger ball up the 6" downrod. Make

sure the support pin is properlyseated in

the grooves inthe top ofthe hanger ball.

4. Tightenthe set screwfirmly.

Figure 12

Outlet box

Hanger

bracket

Canopy

cover

Screws

Finishing the Installation

Step 1. Slide the canopy up to the ceiling and over

the 2 screws on the hanger bracket. Rotate canopy to

lock in place. Next, while holding the canopy with

one hand, slide the canopy cover up and over the

screws, rotate and lock in place.

NOTE: Adjust the canopy screws as necessary until

the canopy and canopy cover are snug. (Fig. 12)

Figure 10

Receiver

Hanger

bracket

ONON

Figure 9

Code switch

WARNING

Make sure thenotch on thehanging bracket

properly sits inthe groove inthe hanger ball

before attaching thecanopy to thebracket by

turning the housinguntil it dropsinto place.

SUPPLYCIRCUIT

WHITE

BLUE

BLACK

White (neutral)

Green or bare

copper (ground)

White ("AC INN")

White ("to motor N")

Orange

(for upper light)

Orange

(for upper light)

Ground

(green)

(Connect to

ground wire on

hanger bracket

if no house

ground wire

exists.)

Outlet box

Black (hot)

Black ("AC INL")

Black ("to motor L")

Receiver

Black (motor)

Figure 10

Blue (for bottom light)

Note: Fan must be installed at a maximum

distance of 20 feet from the transmitting unit

for proper signal transmission between the

transmitting unit andthe fan's receivingunit.

Figure 13

Attaching the top

glass housing

Remember to disconnect the power.

Loose the three screws on the glass housing

assembly. Hold up the glass housing assembly to

ceiling fan assembly, and take the three screws on

the glass housing assembly over the three key

holes in the motor assembly plate, twist clockwise

to set glass housing firmly with motor fan

assembly. Be sure to tighten the three screws to

avoid the glass falling.

NOTE: Check to make sure the three screws

from the glass housing assembly are completely

through the key holes in the fan motor assembly

and sit firmly.

Topglass housing

assembly

Screws

Motor assembly

Rubber

washer

Blade

arm

Figure 14

Blade

Screws

Attaching the Fan

Blades

Step 1 Attach blades to blade arms using

three screws and rubber washers as shown in

Figure 14. Start a screw into the arm, do not

tighten. Repeat for the 2 remaining screws

and washers.

Step 2 Tighten each screw securely starting

with the center screw. Make sure the blade is

straight.

Step 3 Fasten the blade arms to the motor by

inserting the tab from the blade arms to the

slot in the bottom motor housing, then

tighten the two screws and washers already

installed in theblade arms. (Figure15)

Step 4 Install an optionallight kit ifyou wish.

Follow the instructionsincluded with thekit.

Figure 15

Motor

Blade arm

Slot

Tab

All blades are grouped by weight. Because

natural woods very in density, the fan may

wobble even though the blades are weighed

equally.

The following procedure should correct

most fan wobbling problems. Check after

each step.

1. Check that all blade and blade arms

screws are secure.

2. Most fan wobbling problems are caused

when blade levels are unequal. Check this

level by selecting a point on the ceiling

above the tip of one of the blades. Measure

this distance as shown in Figure 16. Rotate

the fan until the next blade is positioned for

measurement. Repeat for each blade. The

distance should be equal within

1/8".

deviation

WARNING

TO REDUCE THERISK OF PERSONALINJURY,

DO NOT BENDTHE BLADE HOLDERS

WHILE INSTALLING,BALANCING THE

BLADES, OR CLEANINGTHE FAN. DO NOT

INSERT FOREIGNOBJECTS BETWEEN

ROTATING FANBLADES.

Touching

ceiling

Figure 16

3. Use the enclosed Blade Balancing Kit if

the blade wobbleis still noticeable.

4. If the blade wobble is still noticeable,

interchanging two adjacent (side by side)

blades can redistribute the weight and

possibly result insmoother operation.

This manual suits for next models

Table of contents

Other HAMPTON BAY Fan manuals

HAMPTON BAY

HAMPTON BAY 48" Roanoke User manual

HAMPTON BAY

HAMPTON BAY Brookedale II User manual

HAMPTON BAY

HAMPTON BAY BPT13-14HD User manual

HAMPTON BAY

HAMPTON BAY AK438-MBK User manual

HAMPTON BAY

HAMPTON BAY Rocio User manual

HAMPTON BAY

HAMPTON BAY Lonestar 52 User manual

HAMPTON BAY

HAMPTON BAY CAMPBELL User manual

HAMPTON BAY

HAMPTON BAY Palisades User manual

HAMPTON BAY

HAMPTON BAY Metarie 795-970 User manual

HAMPTON BAY

HAMPTON BAY BENNINGTON 52389 User manual

HAMPTON BAY

HAMPTON BAY 7107-03 User manual

HAMPTON BAY

HAMPTON BAY BPT18-34A-5 User manual

HAMPTON BAY

HAMPTON BAY 9100 User manual

HAMPTON BAY

HAMPTON BAY SENZE 24816-021 User manual

HAMPTON BAY

HAMPTON BAY BPT12-13E User manual

HAMPTON BAY

HAMPTON BAY 1002 275 335 User manual

HAMPTON BAY

HAMPTON BAY Glendale User manual

HAMPTON BAY

HAMPTON BAY 42010 User manual

HAMPTON BAY

HAMPTON BAY Milton 458 412 User manual

HAMPTON BAY

HAMPTON BAY SINCLAIR User manual

HAMPTON BAY

HAMPTON BAY HAVANA 48-HVA User manual

HAMPTON BAY

HAMPTON BAY FZ-12A User manual

HAMPTON BAY

HAMPTON BAY 51315 User manual

HAMPTON BAY

HAMPTON BAY Torrington User manual

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual