HAMPTON BAY 132 cm Fan User manual

Date Purchased

Store Purchased

Model No.

Serial No.

Vendor No.

UPC

219054

Hampton Bay Lifetime Motor Warranty

The retailer warrants the fan motor to be free from defects in workmanship and material present at time of

shipment from the factory for a lifetime after the date of purchase by the original purchaser. The retailer also

warrants that all other fan parts, excluding any glass or plexiglass parts, to be free from defects in

workmanship and material at the time of shipment from the factory for a period of one year after the date of

purchase by the original purchaser. We agree to correct such defects without charge or at our option replace

with a comparable or superior model if the product is returned to the retailer. To obtain warranty service, you

must present a copy of the receipt as proof of purchase. All costs of removing and reinstalling the product are

your responsibility. Damage to any part such as by accident or misuse or improper installation or by affixing

any accessories, is not covered by this warranty. Because of varying climatic conditions in the United States

this warranty does not cover any changes in brass finish, including rusting, pitting, corroding, tarnishing or

peeling. Brass finishes of this type give their longest useful life when protected from varying weather

conditions. A certain amount of wobble is normal and should not be considered a defect. Servicing performed

by unauthorized persons shall render the warranty invalid. There is no other express warranty. The retailer

hereby disclaims any and all warranties, including but not limited to. Those of merchantability and

fitness for a particular purpose to the extent permitted by law. The duration of any implied warranty

which cannot be disclaimed is limited to the time period as specified in the express warranty. Some states do

not allow limitation on how long an implied warranty lasts, so the above limitation may not apply to you. The

retailer shall not be liable for incidental, consequential, or special damages arising out of or in

connection with product use or performance except as may otherwise be accorded by law. Some states

do not allow the exclusion of incidental or consequential damages, so the above exclusion or limitation may

not apply to you. This warranty gives specific legal rights, and you may also have other rights which vary

from state to state. This warranty supersedes all prior warranties.

Hampton Bay Lifetime Motor Warranty

718212140352 (xxx-xxx)

xxx-xxx

718212140369 (xxx-xxx)

Table of Contents

SAFETY RULES....................................................................................................

PACKAGE CONTENTS ........................................................................................

INSTALLING YOUR FAN.....................................................................................

HANGING THE FAN.............................................................................................

ELECTRICAL CONNECTIONS ..........................................................................

FINISHING THE INSTALLATION.......................................................................

BLADE INSTALLATION ....................................................................................

............................................................

...................................

OPERATING TRANSMITTER....................................................................

CARE OF YOUR FAN..........................................................................................

TROUBLESHOOTING.......................................................................................

SPECIFICATIONS..............................................................................................

INSTALLING THE MOUNTING PLATE

INSTALLING THE LIGHT KIT............................................................................

INSTALLING THE LIGHT BULBS AND GLASS SHADE

THE

1. Before you begin installing the fan, shut power off at the circuit

breaker or the fuse box.

2. Be cautious! Read all instructions and safety information before

installing your new fan. Review accompanying assembly diagrams.

3. Make sure that all electrical connections comply with local codes,

ordinances, or National Electrical Codes. Hire a qualified electrician or

consult a do-it-yourself wiring handbook if you are unfamiliar with

installing electrical wiring.

4. Make sure the installation site you choose allows the fan blades to rotate

without any obstructions. Allow a minimum clearance of 7 feet from the

floor and 18 inches from the tip of the blades to the wall.

5. If you are mounting the fan to a ceiling outlet box, use U.L. Listed

metal octagonal outlet box marked "Acceptable for fan support". Secure

the box directly to the building structure. The outlet box and its support

must be able to support the moving weight of the fan. (at least 35 lbs.) Do

not use a plastic box.

6. Caution: To reduce the risk of personal injury use only the screws

provided with the outlet box.

7. If you are mounting the fan to a joist, make sure it is able to support the

moving weight of the fan (at least 50 lbs.).

8. After you install the fan, make sure that all mountings are secured to

prevent the fan from falling.

9. Do not insert anything into the fan blades while the fan is operating.

10. Turn the fan off and wait for it to stop completely before changing the

fan direction.

NOTE: The important safeguards and instructions appearing in this

manual are not meant to cover all possible conditions and situations that

may occur. It must be understood that common sense, caution and care are

factors which can not be built into this product. These factors must be

supplied by the person(s) installing, caring for and operating the unit.

1. Safety Rules

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR OTHER

PERSONAL INJURY, MOUNT FAN ONLY TO A U.L. LISTED OUTLET BOX

OR SUPPORTING SYSTEM MARKED ACCEPTABLE FOR FAN SUPPORT

AND USE MOUNTING SCREWS AND LOCK WASHERS PROVIDED WITH

THE OUTLET BOX, MOST OUTLET BOXES COMMONLY USED FOR THE

SUPPORT OF LIGHTING FIXTURES ARE NOT ACCEPTABLE FOR FAN

SUPPORT AND NEED TO BE REPLACED. CONSULT A QUALIFIED

ELECTRICIAN IF IN DOUBT.

TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE BLADE

HOLDERS WHILE INSTALLING, BALANCING THE BLADES, OR

CLEANING THE FAN. DO NOT INSERT FOREIGN OBJECTS BETWEEN

ROTATING FAN BLADES.

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS

FAN WITH ANY SOLID-STATE SPEED CONTROL DEVICE.

WARRING

NOTE

READ AND SAVE ALL INSTRUCTIONS!

ATTENTION: The Energy Policy Act of 2005 requires this fan to be

equipped with a 190 watt limiting device. If lamping exceeds 190

watts, the ceiling fan's light kit will shut off automatically.

Unpack your fan and check the contents. You should have the following items;

1 Fan blades (4)

2. Hanger bracket

3. Canopy

4. Canopy cover

5a. Standard downrod assembly

5b. Minimum-length downrod (for close

to the ceiling installation only)

6. Coupling cover

7. Fan motor assembly

8. Mounting plate

9. Light kit

10. Glass shade

11.

12.

13. 40 (3)

14. Balancing kit

Receiver+6 wire nuts

Transmitter+holder+2 mounting screws

Watt candelabra bulbs

Package Contents 2.

a. Mounting Hardware:

Wire nuts (3 Pcs.)

b. Blade Attachment Hardware:

3/16" x 12.3mm Screws (13 PCs.)

Fiber washers (13 Pcs.)

Phillips screw driver; slotted screw driver; step-

ladder; wire cutters; electrical tape.

Tools Required

Mounting Options

Outlet box

Figure 1

Ceiling

joist

Ceiling

joist

Cross brace

Outlet box

Figure 2

Ceiling joist

or cross brace Parallel

wood brace

Provide strong

support

Recessed

outlet box

Hanger bracket

opening must

be facing up-side

Figure 3

Outlet box

Figure 4

Ceiling

joist

Hanger bar

(optional)

Hanger

bracket

Angled ceiling

maximum

18 angle

If there isn't an existing mounting box, then read the

following instructions. Disconnect the power by

removing fuses or turning off circuit breakers.

Secure the outlet box directly to the building

structure. Use appropriate fasteners and building

materials. The outlet box and its support must be able

to fully support the moving weight of the fan (at least

50 lbs.). Use a UL Listed metal outlet box. Do not use

a plastic outlet box.

Figure 1, 2 and 3 are examples of different ways to

mount the outlet box.

Note: You may need a longer downrod to maintain

proper blade clearance when installing on a steep,

sloped ceiling. Longer downrods are available from

your Hampton Bay dealer.

To hang your fan where there is an existing fixture

but no ceiling joist, you may need to install a hanger

bar as shown in Fig. 4 (available at your Hampton

Bay dealer).

3. Installing Your Fan

REMEMBER to turn off the power.

Follow the steps below to hang your fan

properly:

Step 1. Secure the hanger bracket to the

ceiling outlet box using screws included

wi th y our outle t bo x, loc k wa she rs

included with the fan. (Fig.5)

Step 2. Loosen the two set screws and

remove the hitch pin and lock pin in the top

coupling of the motor assembly. (Fig.6)

Step 3. Remove hanger ball from downrod

a s s e m b l y b y l o o s e n i n g s e t s c r e w,

removing the cross pin, and sliding ball off

rod. (Fig.7)

Step 4. Carefully feed fan wires up

through the downrod. (Fig. 8) Thread the

rod into the coupling. Next line up holes

and replace lock pin and hitch pin. Tighten

set screws.

Step 5. Slip coupling cover, canopy cover

a n d c a n o p y o n t o d o w n r o d . ( F i g . 9 )

Carefully reinstall hanger ball onto rod

being sure that cross pin is in correct

position, set screws are tighten and wires

are not twisted.

Step 6. Now lift motor assembly into

position and place hanger ball into hanger

bracket. Rotate until the check groove has

dropped into the registration slot and seats

firmly. (Fig. 10) Rod should not rotate if

this is done correctly.

Outlet box

Hanger bracket

Cross pin

Hanger

ball

Downrod

Supply

wires

Figure 5

Figure 7 Figure 8

Figure 6

Figure 9

Figure 10

Registration

slot

Downrod

Coupling cover

Canopy

Canopy cover

Set screws

Hitch pin

Lock pin

Hitch

pin Lock

Set

screws

Hanger ball

Hanging the Fan 4.

Receiver

Hanger bracket

Figure 11

Figure 12

WARNING: To avoid possible electrical

shock be sure electricity is turned off at the

main fuse or breaker box before wiring.

NOTE: The Hand Held Remote or Wall

Control units included with your ceiling fan

are equipped with 16 code combinations to

prevent possible interference from or to

other remote units. The dip switches on your

Receiver and Transmitter units have been

preset at the factory, please re-check to make

sure the switches on both units are set to the

same positions. The frequency settings

s h o u l d b e c h a n g e d o n l y i n c a s e o f

interference or if a second or more remote

controlled ceiling fans are installed in the

same structure. Any code combination will

operate the ceiling fan and light as long as

the Receiver and Transmitter units are set to

the same codes (Fig. 11)

Step 1. Insert Receiver into Hanger Bracket

with the flat side of the Receiver facing the

ceiling. (Fig. 12)

St ep 2. M ot or to R ec eiver E le ct rical

Connections: Connect the WHITE wire from

the fan to the WHITE wire marked "TO

MOTOR N" from the Receiver. Connect the

BLACK wire from the fan to the BLACK

Wire

marked "TO MOTOR L" from the Receiver.

Connect the BLUE wire from the fan to the

BLUE wire marked "For Light" from the

Receiver. NOTE: If your ceiling fan features

an UP Light: Connect the ORANGE wire

from the fan to the ORANGE wire marked

"For Up Light" from the Receiver. Otherwise

disregard this step and proceed to secure all

wire connections with the plastic wire nuts

provided. (Fig. 13 )

Step 3. Receiver to House Supply Wires

Electrical Connections: Connect the WHITE

wire (Neutral) from the outlet box to the

WHITE wire marked "AC in N" from the

receiver. Connect the BLACK wire (Hot)

from the outlet box to the BLACK wire

marked "AC in L" from the receiver. Secure

all wire connections with the plastic wire

nuts provided. (Fig. 13

Step 4. If your outlet box has a GROUND

wire (Green or Bare Copper) connect this

wire to the Hanger Ball and Hanger Bracket

Ground wires. If your outlet box does not

have a Ground Wire, then connect the

Hanger Ball and Hanger Bracket Ground

Wires together. Secure wire connection with

the plastic wire nut provided. (Fig. 13 )

After all connectors are made, check to make

sure there are no loose strands. As an

additional precaution we suggest to secure

the plastic wire connectors to the wires with

electrical tape.

Note: Fan must be installed at a maximum

distance of 40 feet from the transmitting unit

for proper signal transmission between the

transmitting unit and the fan's receiving

unit.

5. Electrical Connections

Access

window

Blade

Screws

Fiber washers

Figure 14

Outlet box

Hanger

bracket

Hanger

ball

Canopy

cover

Figure 15

7. Blade installation

Rotate motor until holes become visible

through the motor access window. Align the

holes from the blade to the holes from the

motor and secure in place with screws and

fiber washers provided. (Fig. 15)

Fan

White (neutral)

Green or bare

copper (ground)

White ("AC IN N")

White ("to motor N")

Orange

(for upper light)

Orange

(for upper light)

Ground

(green)

(Connect to

ground wire on

hanger bracket

if no house

ground wire

exists.)

Outlet box

Black (hot)

Black ("AC IN L")

Black ("to motor L")

Receiver

Blue (for bottom light)

Black (motor)

Figure 13

6. Finishing the

Installation

Step 1.

Step 2. Slide the canopy up to ceiling and over

the screw on hanger bracket. Rotate canopy

clockwise and tighten the screws. Next, while

holding the canopy with one hand, slide the

canopy cover over the screws and rotate

clockwise until tight. Note: adjust the canopy

screws as necessary until the canopy and

canopy cover are snug. (Fig. 14)

Remove 1 of 2 screws from the

hanger bracket.

Figure 16

8. Installing the

mounting plate

Step 1. Remove 1 of 3 screws from the mounting

ring and loosen the other 2 screws. (Do not

remove)

Step 2. Place the mounting plate key holes

over the 2 screws previously loosened from the

mounting ring, turn mounting plate until it

locks in place at the narrow section of the key

holes. Secure by tightening the 2 screws

previously loosened and the one previously

removed. (Fig. 16).

Screws

Mounting plate

Mounting ring

Screws

Connection plug

Light kit

Mounting plate

Figure 17

9. Installing the light

Kit

NOTE: Before s ta rt in g i ns ta ll at io n,

disconnect the power by turning off the

circuit breaker or removing the fuse at

fuse box.

1. Remove 1 of 3 screws from the mounting

plate and loosen the other 2 screws. (Do

not remove)

2. Raise and hold the light kit close to the

mounting plate and proceed to do the

wire connections. Connect the white wire

connectors from the light kit and fan,

follow the same procedure with the black

wire connectors. (Fig. 17)

3. Place the light kit key holes over the 2

screws previously loosened from the

mounting plate, turn light kit until it

locks in place at the narrow section of the

key holes. Secure by tightening the 2

screws previously loosened and the one

previously removed.

Figure 18

10. Installing the light bulbs and glass shade

NOTE: Before starting installation, disconnect the power by turning off the circuit

breaker or removing the fuse at fuse box.

Install 3 x 40W bulbs ( included).

Raise and hold the glass

shade assembly close to the mounting plate and secure with the screws

previously removed.

ATTENTION: The Energy Policy Act of 2005 requires this fan to be equipped with

a 190 watt limiting device. If lamping exceeds 190 watts, the ceiling fan's light kit

will shut off automatically.

2. Remove the 4 screws from the glass shade assembly.

(Fig. 18)

3. Restore power, your light kit is ready for operation.

candelabra

Mounting

plate

Screws

Bulbs

Glass shade

This manual suits for next models

Table of contents

Other HAMPTON BAY Fan manuals

HAMPTON BAY

HAMPTON BAY Minuet III User manual

HAMPTON BAY

HAMPTON BAY METARIE II 24 User manual

HAMPTON BAY

HAMPTON BAY 52-RDT User manual

HAMPTON BAY

HAMPTON BAY Brookedale User manual

HAMPTON BAY

HAMPTON BAY Babiberre User manual

HAMPTON BAY

HAMPTON BAY Eastridge 640-659 User manual

HAMPTON BAY

HAMPTON BAY BPT13-14HD User manual

HAMPTON BAY

HAMPTON BAY Alida User manual

HAMPTON BAY

HAMPTON BAY YG204D-BN User manual

HAMPTON BAY

HAMPTON BAY AM213-BN User manual

HAMPTON BAY

HAMPTON BAY 68144 User manual

HAMPTON BAY

HAMPTON BAY 58919 User manual

HAMPTON BAY

HAMPTON BAY 52-LASO User manual

HAMPTON BAY

HAMPTON BAY SAN MARINO 91153 User manual

HAMPTON BAY

HAMPTON BAY HOLLY SPRINGS 57281 User manual

HAMPTON BAY

HAMPTON BAY 290-286 User manual

HAMPTON BAY

HAMPTON BAY Farmington User manual

HAMPTON BAY

HAMPTON BAY AG524PR-FB User manual

HAMPTON BAY

HAMPTON BAY SIDLOW 52151 User manual

HAMPTON BAY

HAMPTON BAY MENA 92404 User manual

HAMPTON BAY

HAMPTON BAY Malone User manual

HAMPTON BAY

HAMPTON BAY Trieste User manual

HAMPTON BAY

HAMPTON BAY GAZEBO II YG188-WH User manual

HAMPTON BAY

HAMPTON BAY Thorton User manual

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual