Haier HWD-D1200TXVE User manual

USER MANUAL

Automatic Drum

Washing Machine

HWD-D1200TXVE

HWD-D1200TXVEME

HWD-D1000TXVE

HWD-D1000TXVEME

page no.

Before use

Parts .......................................................................................................... 1

Safety instructions ................................................................................. 2 - 4

Installation ............................................................................................ 5 - 6

Functions .............................................................................................. 7 - 8

Using the appliance

Programme selection ................................................................................. 9

Preparation .............................................................................................. 10

Using your appliance ........................................................................ 11 - 12

Other functions ....................................................................................... 13

Maintenance

Maintenance .................................................................................... 14 - 15

Trouble shooting ..................................................................................... 16

Technical speciﬁcations ............................................................................ 17

Table of contents

This diagram may vary slightly with the layout of the washing machine you

have just purchased due to technical improvements.

NOTICE

Please read these instructions carefully before using this appliance. The

instructions contain important information which will help you get the

best out of the appliance and ensure safe and proper installation, use and

maintenance.

KEEP THIS MANUAL

Keep this manual in a convenient location so you can refer to it to check safe

and proper use of the appliance. If you sell or give the appliance to someone

else, or leave it behind when you move house, make sure you also pass on

this manual so that the new owner can become familiar with the appliance

and safety warnings.

Parts

Selection dial

Detergent

dispenser

Door

Power cable

Earthing terminal

Drain hose

Packing bolts (3)

Hose clip

Back plate

Top panel

Display

Porthole

Back plate

screws (3)

Door handle

Power button

Using your appliance will be simple, but please make sure read the following

to get the best out of it and to ensure your own safety.

BEFORE SWITCHING THE APPLIANCE ON FOR THE FIRST TIME:

✓Ensure you connect the appliance directly to a domestic mains water

supply.

✓Ensure that the appliance is situated on a ﬁrm level base.

✓Ensure that the electrical system meets the requirement laid out in the

installation section of this document.

✓Use a separate earthed socket for the power supply.

✓Make sure that the plug is accessible.

✓Make sure that the power cable is not caught under or in the appliance

and avoid damage to the power cable.

✓Check that hose joints and connections are ﬁrm and no water can leak.

If joints are loose or there is leakage, turn off the tap and repair. Do not

use the washing machine until the hoses are properly ﬁxed.

DO NOT

✗Connect the appliance to the power supply until installation is

complete.

✗Install the appliance outdoors or in a damp place. In the event of a

water leak allow the machine to dry naturally.

✗Expose the appliance to heat sources or direct sunlight to prevent

plastic and rubber components from aging.

✗Use an appliance with missing parts.

Safety instructions

DURING DAILY USE OF THE APPLIANCE

✓Unplug the appliance before carrying out any maintenance or repair.

✓Hold the plug and not the electric cable when unplugging the washing

machine.

✓Keep the door slightly open when not in use to prevent formation of

odours.

✓After each wash programme, turn off the machine and switch it off at

the mains to save electricity and for safety. Wipe clean the lower part of

the porthole.

✓Pull up zips and ﬁx loose threads to prevent the items from being

entangled. If necessary, put small items into a net bag or pillow.

DO NOT

✗Touch or use the appliance when barefoot or with wet or damp hands

or feet.

✗Use ﬂammable detergent or dry cleaning agent.

✗Open the detergent drawer during the wash cycle.

✗Use any ﬂammable sprays in close vicinity to the appliance

✗Remove or insert the plug in the presence of ﬂammable gas

✗Place heavy objects or sources of heat or damp on the top of the

appliance.

✗Obstruct the ventilation openings at the base of the appliance.

✗Attempt to repair the appliance yourself. Contact the manufacturer or

their approved service agent.

✗Allow children or the inﬁrm to play with the appliance or packing

materials, without adult supervision.

✗Touch the porthole during the washing process – it gets hot!

✗Force the door open. The door is ﬁtted with a self-lock device and will

not open until 2-3 minutes after the washing machine stops.

✗Open the door if the water level is visibly over the porthole.

✗Use the appliance if the power cable is damaged. It must be replaced

by the manufacturer, its approved service agent or similarly qualiﬁed

persons in order to avoid a hazard.

✗Wash foam rubber or sponge-like materials on a hot wash.

✗Cover the appliance.

Electrical connection (UK ONLY)

For your safety please read the following information

Warning: This appliance must be earthed.

The appliance must be connected to a 220 volt 240 cycle AC supply by

means of a three pin socket, suitably earthed and should be protected by a

13 amp fuse.

The appliance is supplied with a standard 3 pin mains plug ﬁtted with a 13

amp fuse. Should the fuse require replacement, it must be replaced with a

13 amp fuse approved to BS1362.

The plug contains a removable fuse cover that must be reﬁtted when the

fuse is replaced. In the event of the fuse cover being lost or damaged, the

plug must not be used until a replacement cover has been obtained.

When disposing of the appliance the plug should be cut off as close to

the plug body as possible and the fuse should be removed to prevent an

electrical hazard. Dispose of the plug safely.

The use of adapters, multiple connectors and/or extension cables is not

recommended.

How to wire a 13 amp plug.

Important

The wires in the mains lead on this

appliance are coloured in accordance with

the following code:

Green and Yellow – Earth

Blue - Neutral

Brown - Live

As this may not correspond with your installation, proceed as follows:

The green and yellow wire must be connected to the terminal in the plug

which is marked with the letter E or with the earth symbol ~ or coloured

green and yellow,

The blue wire must be connected to the terminal marked N.

The brown wire must be connected to the terminal marked L.

Safety instructions

Caution: protective gloves should be warn

• Remove all the packing materials

(including the foam base) to prevent

vibration during use, as show in Fig. 1.

On opening, water drops may be visible

on the appliance. This is a normal

phenomenon.

• Check that the appliance is also supplied with the following:

• Remove the packing bolts as shown in

Fig. 2.

The packing bolts are designed for

support of internal components during

transit.

Before use:

1. Remove the back plate.

2. Remove the three packing bolts on

the back plate and take out the hose.

3. Replace the back plate.

4. Fill the holes left by the packing bolts

with the plastic plugs provided.

Attention: The packing bolts and hose

should be kept in a safe place for later

use.

• Levelling the appliance

There are adjustable feet under the

bottom of the appliance. Before use,

the appliance should be adjusted, as

show in Fig. 3, so that it is level. This

will minimise vibrations and thus noise

during use. It will also reduce wear and

tear. We recommend using a spirit level

to level the appliance. 5

Installation

User

manual

Quality

certiﬁcate

Water

hose Hose clip Plastic

plugs

Quantity 1 1 1 1 3

Connecting the hose to the cold

water supply

1. Connect the nut on the water

inlet hose to the connector on

the water valve. Ensure all seals

are in place.

2. Tighten the nut to secure the

hose.

Drain hose

• The height of the drainage outlet must

be between 80-100cm. To prevent the

drain hose from dropping, attach it

using the drain hose clip at the back of

the washing machine.

• Use the hose clip to secure the end

of the drain hose and to prevent the

outﬂow of water. It is recommended

that the length of the drain hose is not extended by way of a hose extension.

In case of absolute need, we recommend that the extension has the same

diameter as the existing hose and does not exceed 250cm in length.

Note: The drain hose should not be underwater and should be securely ﬁxed

and leak-free. When the drain hose is placed on the ground or the height

of the pipe is less than 80cm, the washing machine will continuously drain

while being ﬁlled (self-syphoning).

Connection to the power supply

Before connecting to the power supply, make sure that:

• The socket is suitable or the maximum power of the washing machine (for

safety, fuses in the power circuit should be rated for no less than 13A).

• The supply voltage should be within the values indicated on the

speciﬁcations page.

• The power supply socket and the plug of the washing machine should

be compatible. If they are not compatible, refer to a washing machine

technician or Haier designated service engineer for power cable replacement.

• The washing machine should be earthed and in compliance with applicable

law.

• Additional earthing cables should not be necessary if the socket and plug are

earthed.

• If required, an additional earthing cable should be installed on the upper

back of the washing machine and earthed.

Installation

Water inlet hose nut

Water inlet valve connector

Cont r ol pa nel

A. Power button G. Start/Pause button

B. Programme selection dial H. button

C. Detergent distribution drawer I. Dry button

D. Spin speed setting button J. Extra rinse button

E. Display K. Delay button

F. Wash status indicator L. Wash temperature button

Funct ions

A. Power button

Press this button to switch on the washing machine. Press it again to switch

it off.

B. Programme selection dial

Turn the dial clockwise or anti-clockwise to select the required programme.

(Refer to Programme selection guide).

C. Detergent distribution drawer

Programme descriptions are printed on the front of

the detergent distributor, there are three detergent

compartments numbered 1, 2, 3.

Box 1: Standard washing - extra-fast washing

Box 2: Softener

Box 3: Pre-washing detergent

D. Spin speed setting button

Touch this button to select the desired speed. Refer to page 10 for guidance

on spin speeds.

E. Display

Information such as remaining wash time, temperature and speed setting

and error messages are shown here.

F. Wash status indicator

This light shows the stage of the cycle of the selected programme.

J H G

F E L A

1 2 3

WashRinse Spin Dry

Time

Delay ExtrarinseDry Start/Pause

Rinse

Wash

Prewash

Cotton&Linen

Synthetics

Wool

Quickwash

Spin

Dry

Iron

Air wash

G. Start/Pause button

When the washing machine is connected to the power socket and a

programme is selected, touch this button to start operation. Touch this

button again during operation to pause the programme. The display screen

will ﬂash and the machine will be paused. Press the button again and the

programme will continue.

H. button

Economy wash. This function automatically adjusts water consumption,

wash time and heating time.

The wash load range is:

Prewash: 1kg~6kg;

Cotton: 1kg~6kg;

Synthetic: 1kg~3kg;

Quick wash: 1kg~3kg;

Wash: 1kg~6kg;

Rinse: 1kg~6kg;

Spin: 1kg~6kg

I. Dry button

Touch this button, the corresponding light will come on and the appliance

will dry the laundry after the last spin cycle.

J. Rinse hold button

Rinse hold helps reduce the creasing and odours that occur when you leave

damp laundry in the appliance after the cycle has ﬁnished. The laundry

stays in the water from the last rinse until you deselect the rinse hold button

which will then start the spin programme to ﬁnish off the cycle.

K. Delay button

Touch this button and the washing machine will start operation after the

selected delay period. The corresponding indicator will go on. The delay

range is 0.5-24 hours. Each touch of this button increases the delay by half

an hour. After the delay is selected, press the Start/ Pause button to start

countdown (the time is displayed on the screen until the programme ends).

Note: The delay time must be longer than the programme time, otherwise

the washing machine will start the wash programme immediately.

L. Wash temperature button

Touch this button and the wash temperature will be displayed on the

screen. Select a suitable temperature according to the type of laundry. The

corresponding light will come on.

Functions

This manual suits for next models

Table of contents

Popular Washer manuals by other brands

Tricity Bendix

Tricity Bendix AW 1000 W Operating & installation instructions

Panasonic

Panasonic NA-F60L5WRB operating instructions

GE WSLP1500 Dimensions and installation information

Electrolux

Electrolux EWF1284EDW Service manual

Bosch

Bosch WAN2829BSN User manual and installation instructions

LG TV2516DV3B owner's manual

LG TH2517DSAV owner's manual

VESTEL

VESTEL CMH-XL 7510 TE user manual

AEG

AEG 74335 User information

Johnson

Johnson JWF721A user manual

Beko

Beko WTE7604XLW0 owner's manual

Danby

Danby DTT100A1WDB Owner's use and care guide

Amica

Amica WA 14 Ex operating instructions

Daewoo

Daewoo DWD-F1222 instruction manual

Bosch

Bosch WAS28461AU instruction manual

Miele

Miele PW 6080 Vario manual

Finlux

Finlux FLX108CF220 user manual

Whirlpool

Whirlpool 3LBR5132AN0 Use and care guide