Haier HVS1000 User manual

Table of Contents

Before using the appliance

Matters needing attention......1-3

Installation.............................4-5

Function ...............................6-7

How to operate the wasing machine

Program description table........8

Preparation .............................9

Washing Procedure ..........10-11

Maintenance ..........................12

Technical Specifications ........14

Wiring Circuit .........................15

Maintenance

Troubleshooting Guide ..........13

Operation Manual

Automatic Drum Washing Machine

Name of parts...inside front cover

Slim 5

HVS1000

Top

Handle

Program selector

Detergent dispenser

Name of Parts

Door

Porthole

Function selector

Caution and Warning symbols

Bottom planel

This diagram may be slightly different from the layout of the washing

machine you have just purchased due to techincal improvements

For you safely,any instructions in this manual with this

"Warning"sign must be followed strictly.

For your safety and to prevent damage to the washing

machine,any instructions in this manual with this "Stop"

sign must be followed strictly.

ON/OFF button



Matters Needing Attention

ƽSafety



.A separate earthed socket is required for the

power supply. The washing machine must be

positioned so that the plug is accessible.

2. Hold the plug and not the electric cable when

unplugging the washing machine.

3.Fuses in the power circuit should be rated for 15A.

If the supply cord is damaged, it must be replaced

by the manufacturer, its service agent or similarly

qualified persons in order to avoid a hazard.

4. Do not touch or use the washing machine bare-

footed or when the hands or feet are wet.

5.Do not use flammable detergent or dry clean

ing agent; do not use flammable spray in close

vicinity to the washing machine; do not remove

or insert the plug in the presence of flammable

gas.

6. The door of the washing machine will become hot

during the heating process. Avoid contact with the

door during the heating process. For safety, keep

children away from the washing machine.



Keep children away from the packing materials after unpacked.



Wiring Circuit

Slim 5

HVS1000



8.The washing machine should not be installed

outdoors or in a damp place. In the event of water

leakage or splashes allow the machine to dry

naturally.

10.Keep away from heat sources and direct sunlight

to prevent plastic and rubber components from

aging.

11.During installation, ensure that the electric

cable is not trapped by the washing machine

and avoid damage to the electric cable.

During Use

1. Before use, check the joints of the filling hose,

the tap and the drainage hose for possible

problems from water pressure fluctuations.

If joints are loose or there is leakage, turn

off the tap and repair. Do not use the washing

machine until the hoses are properly fixed.

The appliance is to be connected to the water

mains using new hose-sets

and that old hose

-sets should not be reused

Keep the door slightly open when the washing

machine is not in use to prevent formation of

odors; do not cover the washing machine with

plastic cover so that inside dampness cannot

be kept in.

Matters Needing Attention

9. The carpet must not obstruct the ventilation

openings in the base of the washing machine.

Technical Specifications

Model

Power supply

Power(Max)

Water pressure (MPa)

Washing power(W)

Spinning power(W)

Max. wash load (kg)

Spinning speed (MAX) (r/min)

Wash program

Heating power (W)

Weight (kg)

Anti-Electric shock

Anti-Water class

Slim 5

HVS1000

220V-240V~/(50Hz)

2100

1000

1800

IPX4

200

300

0.03ōpō1





3. Do not place heavy, heating source or wet articles

on the top of the washing machine.

4. Do not hot wash foam rubber or sponge-like

materials.

6. Do not open the detergent distribution drawer

during the wash cycle..



7. The door is fitted with a self-lock device and will not

open until 2~3 minutes after the washing machine

stops. Do not force the door open. Do not open the

door if water level can reach the porthole.

8. After each wash program, turn off the tap to prevent

leakage; and unplug the washing machine and

wipe clean the lower part of the porthole.

Steel wires in bras will pop

out during washing; never

wash bras containing steel

wires.

5. Before washing, do up zippers, buttons and clothes

straps and put small articles, such as socks, laces

or bras, into a washing bag or a pillow.

Matters Needing Attention Troubleshooting

The following circumstances do not constitute problems. Do not contact the maintenance service

until the problem has been confirmed.

Problem Possible cause

The washing machine fails to operate

Poor connection to power supply

Power failure

Door is not properly closed (It will show E1)

Machine has not been switched on

Washing machine cannot be filled

with water

Water tap is not turned on (It will show E4)

Water pressure is less than 0.03Mpa

The inlet hose is kinked

Water supply failure

The program dial is not properly set

The door is not properly closed

The inlet hose filter is blocked

The machine is draining while is

being filled

The height of the drainage hose is below 80cm (it

should be within 80-100cm)

Thedrainagehoseendisinwater

Drainage failure

Drainage hose is blocked (It will show E2)

Drainage hose end is exceed 100cm above the floor

level

The filter is blocked

Strong vibration during spin drying

Not all packing bolts have been removed

Washing machine is located on an uneven surface

Machine load is over 5kg.

Operation stops before completion

of a wash cycle

Water or electricity failure

Washing machine is in soak cycle

Operation stops for a period of time

Washing machine is in soak cycle

Washing machine gives an error message.

Excessive foam in the drum, which

is spilled to the distribution drawer

The detergent is not a low-foaming type or for manual

wash

Excessive use of detergent

Remove all the packing materials (including the

EPE base)to prevent vibration during use, as

shown in the right picture.Upon opening of the

package, water drops may be seen on the plastic

bag and the porthole. This is normal phenomenon

resulting from water test in the factory.

Fig.1

Check attachments and materials with reference to the following

Dismantle the packing bolts as shown in Fig. 2.

The packing bolts are designed for clamping anti-vibration components

inside of the washing machine during the transportation process.

Before use:

1. Remove the back plate;

2. Remove the three packing bolts on the back plate and take out the

rubber hose;

3. Replace the back plate;

4. Fill the holes left by the packing bolts with plastic plugs.

(Attention: The packing bolts and rubber hose should be kept in a safe

place for later use)

Fig.3

Adjusting the washing machine

There are adjustable feet under the bottom of the washing machine. Before

use, the washing machine should be adjusted, as shown in Fig. 3, so that it

is level.

Fig.2

Model

Slim 5

HVS1000

Qty Name Operation

manual

Operation

manual

Quality

certificate Quality certificate

Water

hose

Water hose

Drainage

holder

Drainage holder

Plastic

plugs

Plastic plugs

Installation

11 11

4. Clean the filter Cleaning methods (once a month)

1) Pick up the bottom cover lightly (Fig. 1);

2) Screw out filter by turning counterclockwise (Fig. 2);

3) Flash clean with running water;

4) Replace the filter by turning clockwise and remount the

cover.

Caution: The filter must be in place, or it may lead to

leakage. (

Fig3

)

Fig1

Fig2

Fig3

Warrantly

card

Warrantly card

Hints for Saving Energy

5. Function selecting button

Select functions as required (refer to the "Operational Functions" section).

Hints for saving energy

During operation

1. Collect clothes for one full wash load.

2. Do not overload the washing machine.

3. Pre-wash heavily soiled clothes.

4. Reduce the amount of detergent or choose standard or delicate wash

programs for slightly soiled clothes.

5. Choose a proper washing temperature. Only exceed 60

for heavily

soiled clothes.

6. Do not use more detergent than required.

7. Softening agent makes clothes feel softer and easier to iron.

7. Finish

The washing machine will stop operation automatically when a wash cycle ends. The "End" sign will

appear. Open the door and take out the laundry. Then turn off the tap and unplug the power cable.

4. Setting washing temperature

Press the temperature button until " -- " is displayed if heating is not needed; otherwise, select

an appropriate temperature as required (refer to the "Guide to Operational Program Selection").

6. Washing

Press Start/Pause key and the LCD will display

, which means the washer has started

operation. The LCD will display program remaining time.

he following functions cannot be re-selected.

1).

3).

Temperature Selection Key

Reserve Time Key

Power Clean Key

4). All the functions already completed.

Spin-dry

Pre- wash



Operational Functions



Display Information Introduction

A. Power On/Off Key

Press the key and the washer will be automatically energized, release the key and powe

is disconnected.

B. Program Selection Knob

Turn the knob clockwise/counterclockwise to select the desired program. (please refer to

Program Setting Guidance Table for details)

C. Detergent Distribution Box-See Figure a for the drawer- type Detergent Dispenser

Open the dispenser box and you will see four detergent compartment of 1, 2, 3:

Compartment 1: Pre-wash Detergent

Compartment 2: Washing Detergent

Compartment 3:Softener , Conditioner and Perfume

D. Reservation Selection Key

Press the key to select the desired time when the washing progress completes. When

setting this feature, the indicator lamp on the upper left corner of the key will illuminate.

Time reservation range is from 1 to 24 hours. The reserved time will increase by one

hour at each press of the key. When the feature is set, press Start/Pause key and th

reserve time will be displayed and countdown will start. At the same time, reservation

indicator lamp will start blinking and will go off after th e washer enters into normal

washing progress.

Figure a

Control Panel Function Description

Washing Procedure

Notes: 1) When first using the washing

machine,let it run unloaded for one program

to prevent the laundry from being tainted by

oil or dirty water from the washing machine.

2) Do not overload the washing

machine.

To get the best washing effect, an appropriate washing program should be selected

according to the laundry type.

Note: The above operations refer to conditions without power-off memory. Or the washing

machine will continue operation from where the program was broken. To clear memory,

press the Start/Pause button. Turn off the power for a few seconds and turn on again, all

the settings will be renewed.

1. Loading

Slide out the detergent drawer and put the required detergent and

softening agent into the corresponding boxes. Push back the drawer gently.

Caution:

1) For pre-washing program, detergent should be added to both

compartments 1 and 2. Compartment 2 allows only solid detergents.

For other programs, do not add detergent to compartment 1.

2) Do not overuse softener; otherwise, it will damage the artificial

fibers. Refer to the instructions during use.

2. Adding detergent

3. Selecting washing program

Load Reference

Overalls

(cotton appr 950g)

ƽBlended fabric

clothes

(appr 800g)

T-shirt

(cotton

appr 300g)

ƽJackets (cotton

appr 800g)

ƽWoolen

blankets

(appr 3000)

ƽSingle bed sheets

(cotton appr 800g)

ƽSocks (blended

fabrics appr 50g)

Underwear

(blended fabrics appr 70g)

ƽ

-HDQV

J

ƽPajamas

(appr 200g)

ƽShirts

(appr 300g)

Open the door, put in the laundry piece by piece.

Close the door tightly.



Baby care

ⳳ㑪

Slik

Quickwash

Singlewash

Rinse

Drain

Spin

Power

Slim5

HVS1000

Cottonprewash

Cotton

Synthetic

Wool

Cashmere

㕞㑪

㕞↯

࣪㑪

ẝ咏

ẝ㑪⋫

䗳⋫

ⓖ

ᥦ∈㒛

㑪∈

㑪㑪

Time

Delay time

Rinse hold Temp. Speed

Start/Pause



Functions



Preparation

1.Power supply

Plug in the power supply 220-240V~/50HZ

2.Water supply

Turn on the tap ensure that the water in clear.

Caution:Before staring the washing machine turn on the water

faucet to ensure the water faucet and the water inlet hose are

connected correctly and do not leak

4.Detergent selection

Only special low foam detergent should

be used in automatic drum washing

mashine,form blended or wool fabrics

special deter-gent should ne used.dry

clearning solvent should not be used

such as trichhloroethy-lene or alike

(caution :load the required amount of

detergent only).

3.Laundry treatment

Sort out clothes according to type and extent of dirt.There are

three types of clothes:cotton,synthetical and woolen (silk) fabrics.

Separate white clothes from colored.If whites and coloreds

are combimed for one load,make sure the coloreds are colorfast

-Clothing with frayed edges or yams should be put in a wash

bag or special bag before washing

-repair damged clothing,lose buttons or damaged zips

and hooks before washing.

-Bed sheets and table ware should be loosely loaded and not

folded.

This washing mashine is for househould use and designed

for mechanically washable clothes.When washing,separate

unwashable clothes with reference to clothes labels.

Note.

If Program key is turned after reservation time is set and before program starts, the

reservation will be automatically cancelled.

When reservation feature is activated, the washing start time is fixed. There will be some

difference between the reserved time and the actual program completion time due to differen

water inlet time and load distribution condition during spin

dry process.

E. LCD

LCD is a window to display information including washing status, washing progress,

reservation time, remaining time, heating temperature, spin

dry speed, load selection and error etc.

as well as to display additional features such as power clean, super clean rinse and foaming

auto

check etc.

F. Start/Pause Key

When the washer is energized, select the desired washing program and press the Start/Pau

key. The indicator lamp on the upper left corner of the key will illuminate to indicate that the

washer has started operation. If it needs to pause the washing process, simply press the Start/

Pause key and the indicator lamp and remining time display will blink and the washer enters into

condition. Press the Start/Pause key again to resume washing process.

(Note: Press the Start/Pause key only after the desired program and feature are set.

G. Rinse Hold Key

Press the key lightly,the screen displays the symbol.The washing machine does not drain the

water after the last rinse,but the laundry remains in a soak.To spin the laundry ,press this key

again .The symbol disappears from the screen and the program continues to the end .The

function is used to prevent the laundry creasing when left in the drum for a long time .

H. Temperature Selection Key

Press the key and LCD will display the selected heating temperature, which is adjustable as

needed. Note: 20

oC means cold water washing and no heating is involved.

I. Spin Speed Selection Key

Press the key and LCD will display the selected spin

dry revolution speed, which is adjustable

as needed. (When No Spin

dry feature is selected, the time will decrease correspondingly

J. Load Selection key

Turn the Program Knob to select the desired program (see Program Setting Guidance Table)

Press the key and manually select different programs and power-saving and water-seaving fea-

ture based on the volume of load. LCD will display L-1(2,3,4,5), indicating the washing load is 1

(2,3,4,5) kg and program time will change accordingly. (The feature is not

available in Wool,

Cashmere, Silk, Speedy, Drainage Only and Spin Only Program. Only L

–

1, 2, 3 are available for

Chemical Fiber program. )



Default Program Detergent Usage MethodProgram

Setting

Mode

Recommended

Laundry Capacity Temperature Total

Time

Temperature

Adjustment

Range

Rinse

Hold

Load

Selection

Super

Clean

Rinse

Reserve Compartment

Compartment

Cotton

Pre-wash

Heavily-soiled

Cotton Fabrics 560

1000 3:12

-40-50-

60-90

-40-50-

60-90

-40-50-

-40

-40-50-

YES YES YES YES

ƾƾ

嗟

Cotton Cotton Fabrics 5 60 1000 2:58 YES YES YES YES X

嗟

Synthetic Fsat-colour-

Fiber 3 60 800 1:42 YES YES YES YES X

嗟

Cashmere Cashmere

/40 600 1:10 YES NO YES YES X

嗟

/40 400 1:10 YES NO YES YES X

嗟

Slik Silk /40 400 1:05 YES NO YES YES X

/_ _ 800 0:29 YES NO NO YES X

嗟

Rinse

54001:33 NO YES NO YES X

58000:25/YES YES YES YES XX

嗟

Drain ////0:03 /NO NO NO YES XXX

Spin ///

1000 0:09 /NO NO NO YES XXX

Note:

嗟

means that it needs to add perfume such as softener

meansthatitneedstoadd

detergent otherwise the

desired washing result will not be achieved. X means it must not add

detergent. The data in Speed column is default spin speed of corresponding model (whe

speed is not selected.)

Note: 1.

Washing temperature refers to the highest temperature allowable during the whole

washing process. The washing time varies according to the type of clothes, selected

temperature and feature. The total operation time provid ed in the above table is for

referenceonly(Therewillbeaslightdifferenceduetodifferentwatertemperature.)

Pro

ram Settin

Guidance Table

Power-off Memory Function:Thewasher has power-off memory function.In case of

abrupt power failure or the power must be cut off during a program cycle, the present

settings will be saved and the preset operation will resume when the power is rezum-

ed.If it needs to cancel this feature, press Start/Pause key so that the washer will

will stop temporarily. Turn off the power key and restart the washer after a few

seconds and the feature will be cancelled.

Safety Child Lock Function: During the operation of the program, press down

Temperature key and Load Selection key concurrently and hold for 3 seconds." "

will be displayed indicating that the program is locked. Repeat the above

procedures to unlock.

Foaming Auto

check Function: The washer offers foaming auto- check function, which is

is a solution to incomplete rinse due to over

dispensing of detergent. The washer can

sense the volume of foam formed automatically. When foaming is detected, the

Introduction of Other Functions

2. For clothes made of special materials such as woolens, cashmere and wool, please check if the

clothes has a machine

washing tag and the requests to the temperature.



K. Super-clean Rinse Key

Press the key and super -clean icon in the LCD will illuminate. When the program comes to

softening process, the washer will add an extra rinse process. ( This feature is not available in some

programs. Please see Program Setting Guidance Table for details.)

Functions

Foaming icon

in the LCD will illuminate and an extra rinse cycle will be

added before the program completes. Program time duration will increase automatically.

Quick wash Slightly-soiled

Textiles

Slightly-soiled

Textiles

Slightly-soiled

Textiles

Single

wash

Wool Wool

D. Auto-shower function:

Other manuals for HVS1000

This manual suits for next models

Table of contents

Popular Washer manuals by other brands

Tricity Bendix

Tricity Bendix AW 1000 W Operating & installation instructions

Panasonic

Panasonic NA-F60L5WRB operating instructions

GE WSLP1500 Dimensions and installation information

Electrolux

Electrolux EWF1284EDW Service manual

Bosch

Bosch WAN2829BSN User manual and installation instructions

LG TV2516DV3B owner's manual

LG TH2517DSAV owner's manual

VESTEL

VESTEL CMH-XL 7510 TE user manual

AEG

AEG 74335 User information

Johnson

Johnson JWF721A user manual

Beko

Beko WTE7604XLW0 owner's manual

Danby

Danby DTT100A1WDB Owner's use and care guide

Amica

Amica WA 14 Ex operating instructions

Daewoo

Daewoo DWD-F1222 instruction manual

Bosch

Bosch WAS28461AU instruction manual

Miele

Miele PW 6080 Vario manual

Finlux

Finlux FLX108CF220 user manual

Whirlpool

Whirlpool 3LBR5132AN0 Use and care guide