Haier HA1000 User manual

HA1000\HM1000

Automatic Drum Washing Machine

Table of Contents

Before using

Names of Parts--------------inside front cover

Matters Needing Attention--------------------1-3

Installation----------------------------------------4-5

Control Panel---------------------------------------6

Operational Functions------------------------6-7

During using

Program Selection--------------------------------8

Preparation-----------------------------------------9

Washing Methods---------------------------10-11

Maintenance

Maintenance -------------------------------------12

Trouble Shooting--------------------------------13

Technical Specification-------------------------14

Names of Parts

Drainage hose clip

Back plate

Earth terminal

Power supply cable

Back plate screw (3) Packing bolt (3)

Caution and Warning symbols

For your safety and to prevent damages to the washing machine,

any instructions in this manual with this “Stop” sign shall be

strictly followed.

For your safety, any instructions in this manual with this “Warning”

sign shall be strictly followed.

This diagram may vary slightly with the layout of the washing machine you have just purchased due

to technical improvements.

Drainage hose

Detergent distributor Top

program knob

Operation button

Door

Porthole

Temperature knob

Matters Needing Attention

1. A separate earthed socket is required for the

power supply. After installation of the washing

machine,the power plug should be accessible

during the normal wash.

3. Fuses in the power circuit should be rated

for 15A. Refer to a washing machine techni-

cian or a Haier designated service point for

power cable replacement.

5. Do not use flammable detergent or dry clean-

ing agent; do not use flammable spray in close

vicinity to the washing machine; do not remove

or insert the plug in the presence of flammable

gas.

2. Hold the plug and not the electric cable when

unplugging the washing machine.

4. For your safety, dry hands before touching

the washing machine and wear appropriate

footwear .

6. The door of the washing machine will be-

come hot during the water heating process.

Avoid contact with the door during the heating

process. For safety, keep children away from

the washing machine.

7. Do not allow children play with the packing materials after unpacking.

•Safety

Matters Needing Attention

9. The washing machine should be place in

a well ventilated area maintaing a space

between walls or furniture.

10. Keep away from heat sources and direct

sunlight to prevent plastic and rubber com-

ponents from aging.

8. The washing machine must not be used in

the open or in area of high moisture as water

droplets may form on electrical components,

Air dry the appliance if the washing machine

components become wet.

1. Make sure that the washing machine is se-

curely connected to the water supply,take the

necessory precautions or con-tact the local

service center if the con-nection is poor or there

is a water leakage.

2. After turning the power off, turn the program

knob clockwise to set washing program.

11. During installation, ensure that the elec-

tric cable is not trapped by the washing ma-

chine and avoid damage to the electric

cable.

•Use

Matters Needing Attention

9. Keep the door slightly open when the washing machine is not being used. Never cover

the machine with a plastic sheet.

4. Do not wash foam rubber or similar

sponge materials.

5. Before washing, do up zippers, buttons ,laces

and repair damaged areas,underwear or small

articals should be placed in the laundry bag

or a pillowslip.

Do not wash clothes containing wire frames.

6. Do not open the detergent box during

the wash cycle.

7. The door is fitted with a self-lock device

and will not open until 2~3 minutes after

the washing machine stops. Do not force

the door open. Do not open the door when

water level reaches the port hole.

8. After washing, turn off the tap to prevent

leakage; unplug the washing machine and

wipe clean the lower part of the port hole.

3. Never place heavy objects ,a heating

applianceor a water container on the top

panel of the washing machine.

Installation

Fig 1

•As shown in figure1 remove all the packing materials

(including the foam base).

•Remove the packing screws as shown in figure 2.

The packing bolts protect the appliance from shock during

transportation The steps below should be followed before

using the appliance,

1. Remove the rear panel of the washing machine;

2. Remove the three packing bolts from the rear panel of the

washing machine,the rubber hose and then the shock ab-

sorption channel steel;

3. Reinstall the back plate;

4. Fill the holes left by the packing bolts with plastic plugs.

(Attention: the packing bolts and rubber hose should be kept

in a safe place for later use)

Fig 2

•Adjusting the position of the washing machine .There are

adjustable feet under the bottom of the washing machine. Be-

fore use, the washing machine should be adjusted, as shown in

figure 3, so that it is level.

Fig 3

Installation

Connection of water inlet hose and washing machine

1. Place the water inlet hose nut on the connector

of the water inlet valve.And rotate it clockwise to

screw onto the connector

2. slightly shake the water inlet hose nut to see if

it is tightly and properly fixed.

connector of water inlet valve

water inlet hose nut

Water drainage hose

•The height of the terminal of the water drainage hose should

be between 80cm-100cm, the water drainage hose must be

securely placed on the clip on the back of the washing machine.

•Use the water drainage support supplied as an accessory

for proper installation of the water drainage hose .fix the water

drainage hose support with waterproof sring.Do not use an

excessively long water drainage hose and contact the autho-

rized technician if the water drainage hose needs to be

extended.the water drainage hose should not be extended

more than250cm.(longer extension will result in concurrent

water inflow and outflow).The diameter of the extension hose

should be the same as the original hose.

caution:water drainage hose must not be immersed in water.

the original and extension hoses should be tightly connected .

Connection of power supply

Check the following items before connection to the power supply.

•The socket conforms to the maximun power load(The maximum current load of the

socket and power supply cable should not be less than 15A).

•Power supply voltage conforms to the required value.

•

The power supply socket and the plug of the washing machine are compatible,if they are not

compatible ,Refer to a washing machine technician or a Haier designated service point

for power cable replacement.The washing machine should be connected to an earth

before use.

•Supplementary earth cable should not be necessary if the socket is connected to the

earth.

•Supplementary earth cable should be installed on the upper back of the washing

machine andconnected to an earth if the power supply socket has no earth connection.

80cm

100cm

•

••

Control Panel

A Washing program

Turn the knob clockwise to set the desired wash program .

Caution: Turn off the power and turn the program knob clockwise

for setting desired wash program.

B Washing temperature

Turn the knob clockwise to set the desired temperature.

Temperatures between 30OC-90OC can be setted , Cold wash is se-

lected when the knob is set at *.

HA\HM1000

C Detergent Dispenser.

The detergent dispenser is divided into 3 compartments marked 2,A,C

2 Wash detergent⧊Except liquid detergent⧋

A Softeners, conditioners, perfumes

C Bleach

Operational Functions

G Power light

The light will illuminate when the power supply is connected.

F Power button

Press the button ,washing machine will start working;release the button,

the washing machine will stop.

OFF

E No spin button

When this button is pressed, the spin cycle will be spared but water

drain is still available. This function is useful for hard ironing fabrics,

such as chemical fiber and wool fabrics.

D Cold Wash BUtton.

Press it you need a cold wash.

Release it you need a heating wash.

For cotton, water. can be heated to 90 •.

For synthetic, to 60•and for wool, to 40•.

H Door Lock Light

Remember that only when the washer doesn’t work, we can open the

door. After the washing program finish,after 3 minutes, when the self-lock

meter turn off, we can open the door.

Program Selection

This manual suits for next models

Table of contents

Other Haier Washer manuals

Popular Washer manuals by other brands

Tricity Bendix

Tricity Bendix AW 1000 W Operating & installation instructions

Panasonic

Panasonic NA-F60L5WRB operating instructions

GE WSLP1500 Dimensions and installation information

Electrolux

Electrolux EWF1284EDW Service manual

Bosch

Bosch WAN2829BSN User manual and installation instructions

LG TV2516DV3B owner's manual

LG TH2517DSAV owner's manual

VESTEL

VESTEL CMH-XL 7510 TE user manual

AEG

AEG 74335 User information

Johnson

Johnson JWF721A user manual

Beko

Beko WTE7604XLW0 owner's manual

Danby

Danby DTT100A1WDB Owner's use and care guide

Amica

Amica WA 14 Ex operating instructions

Daewoo

Daewoo DWD-F1222 instruction manual

Bosch

Bosch WAS28461AU instruction manual

Miele

Miele PW 6080 Vario manual

Finlux

Finlux FLX108CF220 user manual

Whirlpool

Whirlpool 3LBR5132AN0 Use and care guide