Hager 34K1 series User manual

I-LS02110

Hager Companies

139 Victor Street

St. Louis, MO 63104

(800) 325-9995

(800) 782-0145 (FAX)

www.hagerco.com Rev 2, 8/16

34K1 & 34K2 SERIES

GRADE 1 CYLINDRICAL ELECTRONIC LOCK

INSTALLATION INSTRUCTIONS

I-LS02110

www.hagerco.com i Rev 2, 8/16

Table of Contents

A. CHECK LIST 1

-LOCK COMPONENTS 2

B. DOOR PREPARATION 3

C. FRAME PREPARATION 4

D. ADJUST FOR DOOR THICKNESS 5

E. LOCK HANDING 6

F. INSTALL LOCK HOUSING 8

I-LS02110

www.hagerco.com 1 Rev 2, 8/16

A. CHECKLIST (4 each AA Batteries Not Included)

Tools

Drill

Drill Bits: Ø1” (Ø31/32” for drive in latch), Ø13/16”, Ø3/8”, Ø5/16”

Hole Saw: Ø2-1/8”

Phillips Screwdriver, #2

Hammer

Chisel

Parts List: Each 34K1 & 34K2 Series lockset includes

•Exterior lock assembly (includes housing, lever and cylinder drive unit)

•Interior lock assembly

•Installation Instructions, I-LS02110

•Programming Manual, (I-LS02111 for 34K1, I-LS02139 for 34K2)

•Door Preparation Template, T-LS02112

•Hardware box includes:

-Electrified lock chassis assembly

-Interior lever + Steel ring

-Exterior rose/chassis mounting plate

-Interior rose/chassis mounting plate

-Latch bolt with deadlock

-2 Keys

-ASA Strike

-Screw Pack includes:

(SB1) Phillips mounting screws M5 x 38mm x4pcs

(SB2) Flat head tapping screws #8x3/4" x2pcs

(SB3) Flat head tapping screws #12-24 x 1” x2pcs

(SB4) Lever release tool

(SB5) Phillips mounting screws M6 x 10mm x2pcs

(optional)

(SB6) Phillips mounting screws M5 x 25mm x2pcs

(SB1)

(SB2)

(SB3)

(SB4)

(SB5)

(SB6)

I-LS02110

www.hagerco.com 2 Rev 2, 8/16

LOCK COMPONENTS:

A. Battery Cover

B. Interior Housing Assembly

C. Interior Mounting Plate

D. Rubber Gasket

E. Electrified Lock Chassis Assembly

F. Exterior Housing Assembly

G. Cylinder Retainer

H. Exterior Lever

I. Interior Lever

J. Interior Rose Assembly

K. Interior Rose/Chassis Mntg Plate

L. Latch Bolt

M. Screw Post

N. Exterior Rose/Chassis Mntg Plate

O. Lock Cylinder

B. DOOR PREPARATION

1. Doors: Steel or Wood

2. Door thickness range: 1-3⁄8" (35mm) ~ 2" (51mm).

3. Match the Backset of your lockset to the corresponding installation (either 2-3⁄8" [60 mm] or 2-

3⁄4" [70 mm] Backset).

4. Place the installation template onto door and mark holes. Drill the Ø2 1⁄8" (54 mm) first, then

drill the two Ø5/16" (8mm) holes for lock chassis mounting followed by two Ø3/8" (9.5mm) holes

(A)

(B)

(C)

(D)

(E)

(F)

(G)

(H)

(I)

(J)

(L)

(K)

(M)

(N)

(O)

I-LS02110

www.hagerco.com 3 Rev 2, 8/16

for exterior Housing Assembly mounting. Drill the Ø13⁄16" (20 mm) hole for through wiring. Drill

the Ø1" (25 mm) cross bore hole for the latch last.

5. Insert latch into Ø1" hole and hold it parallel to door face, mark outline and remove latch. Chisel

11⁄64" (4.3mm) deep or until faceplate is flush with the edge of the door. Insert latch into the

Ø1" hole again, making certain that the latch bolt bevel faces direction of closing door (see

section E for Lock Handing).

6. Secure the latch to the door using two #8x3/4" screws (SB2).

C. FRAME PREPARATION

1. Close the door and mark the horizontal line aligned to the strike.

2. Measure one half of door thickness from door stop to mark vertical center line of strike. Drill Ø1"

(25 mm) hole, 1/2" (12.7 mm) deep at intersection of horizontal and vertical center lines.

3. Chisel out the jamb 3/32" (2.4mm) deep or until strike is flushed with jamb and then secure the

strike to the jamb using two #12-24 x 1” screws (SB3).

I-LS02110

www.hagerco.com 4 Rev 2, 8/16

D. ADJUST FOR DOOR THICKNESS

Install exterior rose mounting plate onto the lock body by rotating it clockwise. Pay attention to the

installation direction of mounting plate’s anti-rotation tabs, they should be pointed toward the door.

1. Please follow the steps below:

a. Rotate exterior rose mounting plate toward cylindrical chassis.

b. Put the lever release tool into the allocated position of exterior rose mounting plate per the

illustration below.

c. Rotate exterior rose mounting plate to door thickness by using the lever release tool.

Lever Release Tool

Anti-Rotation Tabs on

the rose mounting plate

I-LS02110

www.hagerco.com 5 Rev 2, 8/16

E. LOCK HANDING

1. Determine the hand of your door. The product is set up for Right Hand by default.

INFORMATIONAL PURPOSES ONLY! NO ACTION REQUIRED!

Right Hand Door

Left Hand Door

Right Hand

Reverse Door

TOP VIEW

Left Hand

Reverse Door

INTERIOR

EXTERIOR

INTERIOR

EXTERIOR

TOP VIEW

I-LS02110

www.hagerco.com 6 Rev 2, 8/16

2. To change the handing to a left handed door, rotate the exterior and interior rose assemblies 180

degrees. The interior rose is handled in Step 6 on page 10. For the exterior rose, follow the steps

below:

(b). Remove the gasket to access the

four screws shown. Remove the

screws below and take out the exterior

rose assembly, rotating it 180 degrees

for a left handed door.

Re-install the four screws followed by

the gasket & lever to complete the

outside handing change.

(a). Remove the exterior lever

by turning the key 90° and

using the lever removal tool to

push in the catch pin. The

exterior lever catch pin is

facing the left side by default.

EXTERIOR ASSEMBLY

Exterior Rose Assembly

I-LS02110

www.hagerco.com 7 Rev 2, 8/16

F. INSTALL LOCK HOUSING

1. The lock body should have been adjusted for proper door thickness as shown in section D on

page 5.

2. Install lock body (a) into exterior housing. Be sure the lever rotation grooves line up with the

spindle on the lock body and the tailpiece inserts into the cam. Please insure the body is fully

seated.

3. Carefully insert the main cable through the Ø13/16” [20] wiring hole while installing the exterior

housing assembly on the door

Wiring Hole

I-LS02110

www.hagerco.com 8 Rev 2, 8/16

5. Install interior mounting plate with rubber gasket

a. Install interior mounting plate with rubber gasket using the two (SB6) M5 x 25mm

screws, routing the wires as shown on the first image on the next page. Leave screws

loose to adjust the plate.

b. Install (a) interior rose mounting plate using two (SB1) M5 x 38mm screws as shown in

the image on the following page for wire routing and handing.

c. It is very important to make sure the rose mounting plate is installed on the (b)

vertical center line, adjusting the mounting plate as necessary.

d. Verify that the exterior lever is rotating smoothly, and then tighten down the two (SB6)

M5 x 25mm screws

(SB6)

(SB1)

(a)

(b)

4. Remove the battery compartment cover to gain access to

the screws as shown below. Remove the interior escutcheon

from the interior mounting plate by removing the uncovered

screws as shown.

Route Wire

INTERIOR ASSEMBLY

Other manuals for 34K1 series

This manual suits for next models

Table of contents

Other hager Door Lock manuals

hager

hager 2958 Delayed Egress MagLock User manual

hager

hager 4500 Series User manual

hager

hager 3500 Series User manual

hager

hager 3400 Series User manual

hager

hager 4200 SVR Exit Device User manual

hager

hager EQ45 User manual

hager

hager 4500 Series User manual

hager

hager 34K1 series User manual

hager

hager 3221 User manual

hager

hager 46CE User manual

hager

hager 3300 Series User manual

hager

hager 4200 User manual

hager

hager 47PN User manual

Popular Door Lock manuals by other brands

Assa Abloy

Assa Abloy effeff 827A-IP Mounting instructions

We.lock

We.lock SECBNEBL51 instructions

Iseo

Iseo MA1A installation guide

ID Lock

ID Lock 150 user manual

Lockly

Lockly ACCESS TOUCH PRO user manual

iLoq

iLoq G50S user guide

SDC

SDC Z7835 installation instructions

ilco

ilco 452 Installation

Samsung

Samsung shs-h705 user guide

TRU-BOLT

TRU-BOLT 08102017 user manual

CDVI

CDVI 500-LADJ quick start guide

Igloohome

Igloohome Deadbolt 2S Metal Grey Installer/user guide

eSSL

eSSL FL-300 user manual

JAKO

JAKO JKBTNX4 installation guide

Dorma

Dorma MUNDUS PREMIUM GK 50 Mounting instruction

SCOOP

SCOOP Pullbloc 4.1 FS Panik Assembly instruction

Yale

Yale MORTISE 8800 SERIES installation instructions

Siegenia

Siegenia KFV AS3500 Assembly instructions